Childcare Change Centre Animals User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
Childcare
Change Centre “Animals”
Model # 057664-403

2
This product has been manufactured for a child with a maximum age of 12 months or a maximum weight
of 11kgs.
Be aware of the risk of open res and other sources of heat,such as electric bar res,gas res,etc.in the near
vicinity of the changing unit.
Use original accessories and manufacturer approved parts only.
DO NOT use this change pad if any part is torn,broken or missing.
ENSURE that the change centre is completely assembled and check that all parts are securely tightened
before use.
Regularly check all parts for tightness - tighten or replace if required.
Promptly replace worn or broken parts.
Read all instructions before assembly and use of the change centre.
Keep instructions for future use.
FOLLOWTHE MANUFACTURER’S INSTRUCTIONS.
DO NOT LEAVEYOUR CHILD UNATTENDED.
CHILDREN HAVE DROWNED WHILE USING BATH AIDS.
THIS IS NOT A SAFETY DEVICE.
ALWAYS KEEPYOUR BABY WITHIN ARM’S REACH.
NEVER LEAVEYOUR BABY INTHE CARE OF CHILDREN.
ALL BRAKES ON CASTORS / WHEELS MUST BE APPLIED BEFORE PLACINGYOUR CHILD
ONTHE CHANGE PAD OR INTHE BATH.
DO NOT ALLOW OLDER CHILDRENTO CLIMB OR PLAY ON THE CHANGE CENTRE.
SAFETY PRECAUTIONS
WARNING

3
Due to variations in the style and design of our products, the photographs and illustrations shown in this
instruction manual are generic,therefore product fabrics,colour and design may vary from images shown.
CNP Brands reserves the right to alter product specications without notice as a result of our ongoing
policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Childcare Change Centre
Congratulations on your purchase of the Childcare
Change Centre “Animals”.
This product has been designed and developed with safety,
comfort and functionality in mind. Please take the time to read
this manual carefully before using this product and keep it in a
safe place for future reference.
CONGRATULATIONS

4
ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the
box against the list below. If anything is missing, please contact
Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
x2
x2
x1
x1
x1
x1
x4
x12
End panel
Side frame
Change Pad
Bottom shelf
Top frame
Drainage hose
Castors
Bolts

5
Supplied loose in box continued:
ASSEMBLY CONTENTS
There are no accessories recommended for use with this Change Centre.
x1
x3
x1
x1
x1
Bathtub
Storage
containers
Side tray with
towel rail (L+R)
Bath plug
Plastic
assembly tool
Assembly Arm
Fixings x 2
x 4
Screw 10mm

6
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Frame...
1
2
3
Insert side frame into one side of one end panel.
Insert two bolts and secure using plastic assembly tool.
Do not tighten completely.
Insert second side frame into end panel and secure
with bolts,using plastic assembly tool.Do not tighten
bolts completely.
1a.
2a.
2b.
3a.
4Repeat to attach second end panel.4a.

7
6
5
Lay Change Pad face down on a at surface.
Lay Change Pad Assembly Arm onto the
Change Pad.
6a.
6b.
5a.
5b.
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Frame continued...
8
7Attach one Assembly Arm Fixing over the
horizontal bar of the Change Pad Assembly Arm.
Secure with 2 x 10mm Screws.
Repeat for other side
7a.
7b.
8a.
Lay Change Centre at on the oor.
Slide Castors onto end panels.Ensure Castors are
pointing down.
NOTE: Ensure the metal loops are facing up and that the horizontal bar
sits between the pre-drilled holes on the Change Pad.

8
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Frame continued...
Stand Change Centre upright.
Connect press studs on Change Pad webbing
with press studs on Side Panel.
Tighten all bolts until rm.
11a.
11b.
11c.
11
10 Insert one Assembly Bolt into the front side hole
and secure using the Assembly Tool.
Insert one Assembly Bolt into the back side hole
and secure using the Assembly Tool.
Repeat for other side.
10a.
10b.
10c.
99a.
9b.
With Change Centre still lying on its side, insert
Change Pad Assembly between the two Side
Panels and into the top holes.
Ensure the‘U’ bar on the front of the assembly
is pointing down toward the ground to ensure
Change Pad can be operated correctly.

9
1Place bottom shelf in position as shown.
Fold up sides and attach end aps around
vertical bars of side panels,using press studs to
secure as shown.
1a.
1b.
To attach Bottom Shelf...
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Plastic Components...
11a. Place the three storage containers into position on
the upper rails of the side frames,creating a shelf in
the centre of the unit.

10
ASSEMBLY / OPERATING INSTRUCTIONS
To lower Change Pad...
Change Pad Operation...
1Disengage change pad press studs.
1a.
2
3
4
Place the left component of the side tray into
position,then place the right component ensuring
it clips into the left component as shown.Ensure the
side tray rests against the bar on the top frame.
Place bathtub into position as shown
Insert plug into bath drain hole.
2a.
3a.
4a.
To assemble Plastic Components...