Chroma Space Force 650-9070 User manual

Space ForceTM octo LumenRadio Card QSG V2.0 QSG P/N: 650-0902
Quick Start Guide
Chroma-Q®
Space Force™octo
LumenRadio Card
For a full product manual please visit www.chroma-q.com
Part Number: CHFPFLR
Model: 650-9070
For use with
Part Number: CHSPF[XXXX], CQ647-XXXX, CQ1512-XXXX
Model: 650-XXXX, 647-XXXX, 1512-XXXX

Space ForceTM octo LumenRadio Card QSG V2.0 QSG P/N: 650-0902
1. Overview
The Chroma-Q®Space Force™ octo LumneRadio Card Kit allows addition of RF connectivity to
the Space Force™ octo light fixture. For a complete list of accessories please visit www.chroma-
q.com.
2. Kit Contents
Items
Part Number
Quantity
Radio Printed Circuit Board
650-0325
1
Round Spacer 5/16”
900-1321
2
Screw M3X20 Machine Screw
430-1220-0
2
Grommet for Antenna
430-1220-0
1
3. Tools Required
Torx T8 x 70mm Screwdriver (maximum torque: 0.62 N-m/ 5.5 in ‐ lb)
#1 Phillips Screwdriver or bit (Torque 5.5 in-lb)
4. Procedure
1. Place Space Force™unit acrylic side down on a surface
that will not scratch the lens, or damage the unit.
2. Carefully remove the 4 Torx screws that secure the ABS
plastic back cover. These screws have a T8 Torx head. If
using a power driver, set torque to 5.5 in-lb. Set aside the
screws.
3. Carefully lift the back cover from the unit. The adjusting
knobs will slide off with the cover. Remove the 5-pin
overlay connector from the PCB board before completely
removing the cover. Do not bend the pins. Set back cover
aside.
4. Remove the 4 x M3 screws from the PCB bracket
assembly using a Philip’s #1 screwdriver. If using a power
driver, set torque to 5.5lb-in. Set screws aside. On the
grounding side, there is a star washer- be sure this does
not fall into the unit. Set aside the hardware.
5. Unplug the engine connectors (white and
orange wires) from the PCB bracket
assembly to turn the assembly over and
expose the internal components. The order
of these connectors is not critical when
replacing them later.

Space ForceTM octo LumenRadio Card QSG V2.0 QSG P/N: 650-0902
6. Remove the jumper from the PCB
addressing card inside of the assembly. This
will not be required after you install the
wireless card.
7. Remove the 2 x M3 screws from the PCB addressing card. These will not be required after
you install the wireless card.
8. Included in the kit are two #4 Nylon 5/16” spacers. They
must be positioned as shown in the photograph.
9. Install the wireless card on top of these spacers and
into the jumper port as shown in the diagram. Use a #1
Phillips screwdriver to install the 2 - M3x20 screws
included in the kit to secure the wireless card. If using a
power driver, set torque to 5.5lb-in.
10. Insert the grommet attached to the antenna into the
holes on the engine. Ensure that the antenna does not
come out of grommet.
11. Reassemble the unit in the reverse order. Please remember
- Do not over-torque the screws. If possible, use the recommended torques in this guide.
- Reassemble the ground to the PCB bracket assembly using the M3 star washer.
- When re-assembling the back cover, be sure to carefully plug the overlay 5 pin connector
back into the addressing card. Ensure all 5 pins are connected and carefully adjust the
harness so it does not interfere with the display or closing of the unit.
- Be sure the placement of the back cover is even before replacing the screws. Check all
corners before proceeding.
- Test for operation of unit prior to returning to service.
5. Further Information
Please refer to the Chroma-Q®Space ForceTM manual for more detailed information. A copy of
the manual can be found at the Chroma-Q®website –www.chroma-q.com/support/downloads
Spacer
Spacer
M3X20 Screw
Grommet

Space ForceTM octo LumenRadio Card QSG V2.0 QSG P/N: 650-0902
Approvals & Disclaimer
The information contained herein is offered in good faith and is believed to be accurate.
However, because conditions and methods of use of our products are beyond our
control, this information should not be usedinsubstitution for customer's tests to ensure
that Chroma-Q®products are safe, effective, and fully satisfactory for the intended end
use. Suggestions of use shall not be taken as inducements to infringe any patent.
Chroma-Q®sole warranty is that the product will meet the Chroma-Q®sales
specifications in effect at the time of shipment. Your exclusive remedy for breach of
such warranty is limited to refund of purchase price or replacement of any product
shown to be other than as warranted.
Chroma-Q®reserves the right to change or make alteration to devices and their
functionality without notice due to on-going research and development.
The Chroma-Q®Space ForceTM has been designed specifically for the lighting industry.
Regular maintenance should be performed to ensure that the products perform well in
the entertainment environment.
If you experience any difficulties with any Chroma-Q®products please contact your
selling dealer. If your selling dealer is unable to help, please contact
[email protected]. If the selling dealer is unable to satisfy your servicing needs,
please contact the following for full factory service:
Outside North America:
Tel: [phone]
Fax: [phone]
[email protected]
North America:
Tel: [phone]
Fax: [phone]
[email protected]
For further information please visit the Chroma-Q®website at www.chroma-q.com.
Chroma-Q®is a trademark, for more information on this visit
www.chroma-q.com/trademarks.
The rights and ownership of all trademarks are recognized