Circutor CVM-C10 User manual

INSTRUCTION MANUAL
(M001B01-03-21A)
Power analyzer
CVM-C10

2
CVM-C10
Instruction Manual

SAFETY PRECAUTIONS
DISCLAIMER
CIRCUTOR, SA reserves the right to make modifications to the device or the unit specifications set
out in this instruction manual without prior notice.
CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device specifica-
tions and the most updated manuals.
www.circutor.com
CIRCUTOR, recommends using the original cables and accessories that are supplied
with the device.
DANGER
Warns of a risk, which could result in personal injury or material damage.
ATTENTION
Indicates that special attention should be paid to a specific point.
Follow the warnings described in this manual with the symbols shown below.
If you must handle the unit for its installation, start-up or maintenance, the following should be
taken into consideration:
Incorrect handling or installation of the unit may result in injury to personnel as well as damage to the
unit. In particular, handling with voltages applied may result in electric shock, which may cause death
or serious injury to personnel. Defective installation or maintenance may also lead to the risk of fire.
Read the manual carefully prior to connecting the unit. Follow all installation and maintenance in-
structions throughout the unit’s working life. Pay special attention to the installation standards of the
National Electrical Code.
Refer to the instruction manual before using the unit
In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can result
in injury or damage to the unit and/or installations.
CIRCUTOR, SA reserves the right to modify features or the product manual without prior notification.
3
Instruction Manual
CVM-C10

CONTENTS
SAFETY PRECAUTIONS .........................................................................................................................................................3
DISCLAIMER ..........................................................................................................................................................................3
CONTENTS.............................................................................................................................................................................4
REVISION LOG .......................................................................................................................................................................6
1. VERIFICATION UPON RECEPTION....................................................................................................................................7
2. PRODUCT DESCRIPTION .................................................................................................................................................7
3. DEVICE INSTALLATION....................................................................................................................................................9
3.1.- PRIOR RECOMMENDATIONS ....................................................................................................................................9
3.2.- INSTALLATION .......................................................................................................................................................10
3.3.- CVM-C10-FLEX: ROGOWSKI SENSORS ..................................................................................................................10
3.4.- DEVICE TERMINALS............................................................................................................................................... 12
3.4.1.- LIST OF TERMINALS, CVM-C10-ITF, CVM-C10-MC AND CVM-C10-mV MODELS ......................................... 12
3.4.2.- LIST OF TERMINALS, CVMC10ITFIN AND CVMC10MCIN MODELS..................................................... 13
3.4.3.- LIST OF TERMINALS, CVM-C10-FLEX MODEL.............................................................................................. 14
3.5.- CONNECTION DIAGRAM......................................................................................................................................... 15
3.5.1.- MEASURING THREEPHASE NETWORKS WITH A 4WIRE CONNECTION, CVMC10ITF AND CVM-C10-mV
MODEL...................................................................................................................................................................... 15
3.5.2.- MEASURING THREEPHASE NETWORKS WITH A 4WIRE CONNECTION, CVMC10ITFIN MODEL.......... 16
3.5.3.- MEASURING THREEPHASE NETWORKS WITH A 4WIRE CONNECTION CVM-C10-MC MODEL................ 17
3.5.4.- MEASURING THREEPHASE NETWORKS WITH A 4WIRE CONNECTION CVM-C10-MC-IN MODEL...........18
3.5.5.- MEASURING THREEPHASE NETWORKS WITH A 4WIRE CONNECTION, CVM-C10-FLEX MODEL ............ 19
3.5.6.- MEASURING THREEPHASE NETWORKS WITH A 3WIRE CONNECTION, CVMC10ITF AND CVM-C10-mV
MODEL. ................................................................................................................................................................... 20
3.5.7.- MEASURING THREEPHASE NETWORKS WITH A 3WIRE CONNECTION, CVMC10MC MODEL. ............. 21
3.5.8.- MEASURING THREEPHASE NETWORKS WITH A 3WIRE CONNECTION, CVMC10FLEX MODEL........... 22
3.5.9.- MEASURING THREEPHASE NETWORKS WITH A 3WIRE CONNECTION AND TRANSFORMERS WITH AN
ARON CONNECTION, CVMC10ITF AND CVMC10MC MODELS. ..........................................................................23
3.5.10.- MEASURING TWOPHASE NETWORKS WITH A 3WIRE CONNECTION, CVMC10ITF, CVMC10MC AND
CVM-C10-mV MODELS............................................................................................................................................24
3.5.11.- MEASURING TWOPHASE NETWORKS WITH A 3WIRE CONNECTION, CVMC10ITFIN AND
CVMC10MCIN MODELS........................................................................................................................................25
3.5.12.- MEASURING TWOPHASE NETWORKS WITH A 3WIRE CONNECTION, CVMC10FLEX MODEL..............26
3.5.13. MEASURING SINGLEPHASE NETWORKS, PHASE TO PHASE, WITH A 2WIRE CONNECTION,
CVMC10ITF, CVMC10MC AND CVMC10mV MODELS. ....................................................................................27
3.5.14.- MEASURING SINGLEPHASE NETWORKS, PHASE TO PHASE, WITH A 2WIRE CONNECTION,
CVM-C10-FLEX MODEL. ..........................................................................................................................................28
3.5.15.- MEASURING SINGLEPHASE NETWORKS, PHASE TO NEUTRAL, WITH A 2WIRE CONNECTION,
CVMC10ITF, CVMC10MC AND CVMC10mV MODELS. ....................................................................................29
3.5.16.- MEASURING SINGLEPHASE NETWORKS, PHASE TO NEUTRAL, WITH A 2WIRE CONNECTION,
CVM-C10-FLEX MODEL. .......................................................................................................................................... 30
4. OPERATION.................................................................................................................................................................... 31
4.1.- MEASURING PARAMETERS....................................................................................................................................32
4.2.- KEYBOARD FUNCTIONS .........................................................................................................................................33
4.3.- DISPLAY.................................................................................................................................................................35
4.3.1. cos φ- PF (POWER FACTOR BAR ..................................................................................................................35
4.3.2. ANALOGUE BAR .............................................................................................................................................36
4.3.3. OTHER SYMBOLS ON THE DISPLAY ...............................................................................................................36
4.4.- LED INDICATORS....................................................................................................................................................37
4.5.- OPERATION PROFILES...........................................................................................................................................37
4.5.1. ANALYZER PROFILE........................................................................................................................................37
4.5.2. e3PROFILE ....................................................................................................................................................42
4.5.3. USER ..............................................................................................................................................................44
4.6.- HARMONICS...........................................................................................................................................................44
4.7.- INPUTS...................................................................................................................................................................45
4.8.- OUTPUTS...............................................................................................................................................................45
4.9.- PROGRAMMING .....................................................................................................................................................46
4.9.1. PRIMARY VOLTAGE .........................................................................................................................................47
4.9.2. SECONDARY VOLTAGE....................................................................................................................................48
4.9.3. PRIMARY CURRENT .......................................................................................................................................48
4
CVM-C10
Instruction Manual

4.9.4. SECONDARY CURRENT  MODEL CVM-C10-ITF) ...........................................................................................49
4.9.5. PRIMARY NEUTRAL CURRENT  MODELS: CVM-C10-ITF-IN AND CVM-C10-MC-IN) ..................................49
4.9.6. SECUNDARY NEUTRAL CURRENT MODEL CVM-C10-ITF-IN) ..................................................................... 50
4.9.7. NUMBER OF QUADRANTS............................................................................................................................. 50
4.9.8. MEASUREMENT CONVENTION ..................................................................................................................... 50
4.9.9. TYPE OF INSTALLATION................................................................................................................................. 51
4.9.10. MAXIMUM DEMAND INTEGRATION PERIOD................................................................................................ 51
4.9.11. DELETING MAXIMUM DEMAND....................................................................................................................52
4.9.12. SELECTING THE OPERATION PROFILE.........................................................................................................52
4.9.13. BACKLIGHT, TURNING ON THE BACKLIT DISPLAY .......................................................................................53
4.9.14. SELECTING THE Cos φ- PF BAR ON THE DISPLAY ......................................................................................54
4.9.15. DELETING MAXIMUM AND MINIMUM VALUES............................................................................................54
4.9.16. DELETING ENERGY VALUES.........................................................................................................................54
4.9.17. SELECTING THE RANGE OF ENERGIES.........................................................................................................55
4.9.18. ACTIVATING THE HARMONICS DISPLAY SCREEN.........................................................................................55
4.9.19. kgC02CARBON EMISSION RATIO OF GENERATED ENERGY.........................................................................56
4.9.20. kgC02CARBON EMISSION RATIO OF CONSUMED ENERGY.........................................................................56
4.9.21. COST RATIO OF GENERATED ENERGY..........................................................................................................57
4.9.22. COST RATIO OF CONSUMED ENERGY......................................................................................................... 58
4.9.23. PROGRAMMING ALARM 1 RELAY 1)........................................................................................................... 58
4.9.24. PROGRAMMING ALARM 2 RELAY 2...........................................................................................................63
4.9.25. PROGRAMMING ALARM 3 DIGITAL OUTPUT T1........................................................................................63
4.9.26. PROGRAMMING ALARM 4 DIGITAL OUTPUT T2 ...................................................................................... 66
4.9.27. OPERATING MODE OF DIGITAL INPUT 1...................................................................................................... 66
4.9.28. OPERATING MODE OF DIGITAL INPUT 2..................................................................................................... 66
4.9.29. RS-485 COMMUNICATIONS: PROTOCOL......................................................................................................67
4.9.30. LOCKING THE PROGRAMMING ....................................................................................................................70
4.10.- COMMUNICATIONS ..............................................................................................................................................72
4.10.1. CONNECTIONS...............................................................................................................................................72
4.10.2. PROTOCOL ....................................................................................................................................................73
4.10.3. MODBUS COMMANDS...................................................................................................................................74
4.10.4. BACnet PROTOCOL........................................................................................................................................84
4.10.5. MAPA PICS ................................................................................................................................................... 85
5. TECHNICAL FEATURES................................................................................................................................................. 88
6. MAINTENANCE AND TECHNICAL SERVICE ...................................................................................................................92
7. GUARANTEE...................................................................................................................................................................92
8. CE CERTIFICATE ............................................................................................................................................................93
5
Instruction Manual
CVM-C10

REVISION LOG
Table 1: Revision log.
Date Revision Description
04/14 M001B01-03-14A Initial Version
06/14 M001B01-03-14B Changes in the following sections:
3.4 - 4.9 - 4.10 - 5
06/14 M001B01-03-14C Changes in the following sections:
4.9.5 - 4.9.6 - 4.10.2.1
11/14 M001B01-03-14D Changes in the following sections:
4.9.21 - 4.9.23 - 4.10.2 - 4.10.3 - 5
11/14 M001B01-03-14E Changes in the following sections:
3.3.2 - 3.4.2 - 3.4.8 - 4.5 - 4.9 - 4.10.3.1
01/15 M001B01-03-15A Changes in the following sections:
2 - 3.3.- 3.4- 4.1- 4.9.4 -4.9.28 - 4.10 - 4.10.3.2 - 5
10/15 M001B01-03-15B
Changes in the following sections:
4.2 - 4.5.1 - 4.5.3 - 4.6 - 4.7 - 4.9 - 4.9.1 - 4.9.9 - 4.9.12 - 4.9.22.-
4.9.24 - 4.10.5
12/15 M001B01-03-15C Changes in the following sections:
3.2.- 4.- 4.3.1.- 4.9.- 4.10.3.6.- 4.10.4.- 4.10.5.- 5.
07/16 M001B01-03-16A Changes in the following sections:
4.9.23
02/17 M001B01-03-17A Changes in the following sections:
2.- 3.3.- 3.4.- 3.5.- 4.7.- 4.8.- 4.9.- 4.10.3.6.- 4.10.3.7 - 5
07/17 M001B01-03-17B Changes in the following sections:
5. - 8.
10/17 M001B01-03-17C Changes in the following sections:
3.3 - 5.
06/18 M001B01-03-18A
Changes in the following sections:
2.- 3.4.2.- 3.5.- 4.1.- 4.5.1.- 4.5.3.- 4.8.- 4.9.5.- 4.9.23.- 4.10.3.1.
- 4.10.3.7.2.- 4.9.25.- 4.9.26.- 4.10.3.7.13.- 5.
01/19 M001B01-03-19A Changes in the following sections:
3.3.
02/19 M001B01-03-19B Changes in the following sections:
5.
05/19 M001B01-03-19C Changes in the following sections:
4.5.1.- 4.10.3.7.
10/19 M001B01-03-19D Changes in the following sections:
2.- 4.3.- 4.4.
04/20 M001B01-03-20A Changes in the following sections:
4.10.3.3.- 5.
05/21 M001B01-03-21A Changes in the following sections:
5.
Note: Devices images are for illustrative purposes only and may differ from the actual device.
6
CVM-C10
Instruction Manual

1. VERIFICATION UPON RECEPTION
Check the following points when you receive the device:
a) The device meets the specifications described in your order.
b) The device has not suffered any damage during transport.
c) Perform an external visual inspection of the device prior to switching it on.
d) Check that it has been delivered with the following:
- An installation guide,
- 2 Retainers used to attach the device,
- 5 connectors.
If any problem is noticed upon reception, immediately contact the transport com-
pany and/or CIRCUTOR's after-sales service.
2. PRODUCT DESCRIPTION
The CVM-C10 device measures, calculates and displays the main electrical parameters of the follow-
ing networks: single-phase, two-phase, with and without neutral, balanced three-phase, with ARON
measurements or unbalanced.The measurement will be taken in RMS with the three AC voltage inputs
and three current inputs.
There are 6 versions of the device, depending on the type of current input:
CVM-C10-ITF, indirect current measurement with/5A or/1A transformers.
CVM-C10-ITF-IN, indirect current measurement with/5A or/1A transformers and an input to
measure the neutral current.
CVM-C10-MC, indirect current measurement with efficient transformers of the MC1 and MC3
series.
CVM-C10-MC-IN, indirect current measurement with efficient transformers of the MC1 and
MC3 series and an input to measure the neutral current.
CVM-C10-mV indirect current measurement with/0.333V transformers.
CVM-C10-FLEX current measurement through Rogowski sensors.
The device features:
- 3 keys that allow you to browse between the various screens and program the device.
- 3 indicator LEDs: CPU, ALARM and KEY.
- LCD display, displays all parameters,
7
Instruction Manual
CVM-C10

- 2 digital inputs, used to select the tariff or detect the logic state of external signals.
- 2 digital outputs, fully programmable.
(Not available in the CVM-C10-ITF-IN, CVM-C10-MC-IN and CVM-C10-FLEX models)
- 2 alarm relays, fully programmable (Not available in the CVM-C10-FLEX model)
- RS-485 Communications, with two serial protocols: MODBUS RTU© and BACnet.
8
CVM-C10
Instruction Manual

3. DEVICE INSTALLATION
3.1.- PRIOR RECOMMENDATIONS
In order to use the device safely, it is critical that individuals who handle it follow the
safety measures set out in the standards of the country where it is being used, use the
necessary personal protective equipment, and pay attention to the various warnings
indicated in this instruction manual.
The CVM-C10 device must be installed by authorised and qualified staff.
The power supply plug must be disconnected and measuring systems switched off before handling, al-
tering the connections or replacing the device. It is dangerous to handle the device while it is powered.
Also, it is critical to keep the cables in perfect condition in order to avoid accidents, personal injury and
damage to installations.
The manufacturer of the device is not responsible for any damage resulting from failure by the user
or installer to heed the warnings and/or recommendations set out in this manual, nor for damage
resulting from the use of non-original products or accessories or those made by other manufacturers.
If an anomaly or malfunction is detected in the device, do not use it to take any measurements.
Inspect the work area before taking any measurements. Do not take measurements in dangerous ar-
eas or where there is a risk of explosion.
Disconnect the device from the power supply (device and measuring system power
supply) before maintaining, repairing or handling the device's connections.
Please contact the after-sales service if you suspect that there is an operational fault
in the device.
9
Instruction Manual
CVM-C10

3.2.- INSTALLATION
The device will be installed on a panel (92+0.8 x 92+0.8 mm panel drill hole, in compliance with DIN
43700). All connections are located inside the electric panel.
Terminals, opening covers or removing elements can expose parts that are hazardous
to the touch while the device is powered. Do not use the device until it is fully installed.
The device must be connected to a power circuit that is protected with gl (IEC 269) or M type fuses with
a rating of 0.5 to 2 A. It must be fitted with a circuit breaker or equivalent device, in order to be able to
disconnect the device from the power supply network.
The power and voltage measuring circuit must be connected with cables that have a minimum
cross-section of 1mm2.
The secondary line of the current transformer will have a minimum cross-section of 2.5 mm2.
The temperature rating of insulation of wires connected to the device will be at minimum 62ºC.
3.3.- CVM-C10-FLEX: ROGOWSKI SENSORS
The CVM-C10-FLEX model measures currents using flexible sensors, based on the Rogowski coil prin-
ciple.
The flexibility of the sensor allows it to measure an alternating current irrespective of the position of
the conductor.
CIRCUTOR has a Rogowski sensor model that can be used with the CVM-C10-FLEX: FLEX-MAG.
Table 3 shows the connection of the sensors and Table 2 the maximum position error.
Note: For more information, consult the corresponding sensor guide.
Table 2: Position error.
Position Error
A
B
A± 1%
BA ± 3%
10
CVM-C10
Instruction Manual

Table 3: Probe cable terminal connections
Probe cable terminal connections
FLEX-MAG
Canal de medida / Measuring channel
Común / Common
Shield
Black : Shield (SHLD)
Blue: Common (C)
Green: Measuring channel (L1, L2, L3, N)
11
Instruction Manual
CVM-C10

3.4.- DEVICE TERMINALS
3.4.1.- LIST OF TERMINALS, CVM-C10-ITF, CVM-C10-MC AND CVM-C10-mV MODELS
Table 4: List of terminals of the CVM-C10-ITF, CVM-C10-MC and CVM-C10-mV.
Device terminals
1 : A1 Auxiliary power supply. 13: I2, digital input 2/tariff selection
2: A2 Auxiliary power supply. 14: VL1, Voltage input L1
3: Rc, Common relay output 15: VL2, Voltage input L2
4: R2, Relay output 2 16: VL3,Voltage input L3
5: R1, Relay output 1 17: N, Neutral
6: CT, Common digital output. 18: S1 , Current input L1
7: T2, Digital output 2 19: S2, Current input L1
8: T1, Digital output 1 20: S1, Current input L2
9: A(+), RS485 21: S2, Current input L2
10: B(-), RS485 22: S1, Current input L3
11: GND, for RS485 and digital inputs 23: S2, Current input L3
12: I1, digital input 1/tariff selection
1
23 4 5 6 7 8910 11 12
13
14 15 16 17 18 19 20 21 22 23
POWER SUPPLY
INPUTS
A(+) B(-)
GND
RS485
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
300V
~
Ph-NPh-Ph
520V ~
NV
L3L2 V L1 V
P1 P2 P1 P2
I1 I2
OUTPUTS
Rc R2 R1 Tc T2 T1
S0- S0+ S0+
Figure 1: Terminals of the CVM-C10-ITF, CVM-C10-MC and CVM-C10-mV.
12
CVM-C10
Instruction Manual

3.4.2.- LIST OF TERMINALS, CVMC10ITFIN AND CVMC10MCIN MODELS.
Table 5: List of terminals of the CVM-C10-ITF-IN and CVM-C10-MC-IN.
Device terminals
1 : A1 Auxiliary power supply. 12: I2, digital input 2/tariff selection
2: A2 Auxiliary power supply. 13: VL1, Voltage input L1
3: Rc, Common relay output 14: VL2, Voltage input L2
4: R2, Relay output 2 15: VL3,Voltage input L3
5: R1, Relay output 1 16: N, Neutral
6: S2, Neutral current input 17: S1 , Current input L1
7: S1, Neutral current input 18: S2, Current input L1
8: A(+), RS485 19: S1, Current input L2
9: B(-), RS485 20: S2, Current input L2
10: GND, for RS485 and digital inputs 21: S1, Current input L3
11: I1, digital input 1/tariff selection 22: S2, Current input L3
1
23 4 5 6 7 89 10 11
12
13 14 15 16 17 18 19 20 21 22
POWER SUPPLY
INPUTS
A(+) B(-)
GND
RS485
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
300V
~
Ph-NPh-Ph
520V ~
NV
L3L2 V L1 V
P1 P2 P1 P2
I1 I2
OUTPUTS
Rc R2 R1
S1
S2
LN
P1
P2
Figure 2: Terminals of the CVM-C10-ITF-IN and CVM-C10-MC-IN.
13
Instruction Manual
CVM-C10

3.4.3.- LIST OF TERMINALS, CVM-C10-FLEX MODEL
Table 6: List of terminals of the CVM-C10-FLEX.
Device terminals
1 : A1 Auxiliary power supply. 10: VL3,Voltage input L3
2: A2 Auxiliary power supply. 11: N, Neutral
3: A(+), RS485 12: L1, Current input L1
4: B(-), RS485 13: L2, Current input L2
5: GND, for RS485 and digital inputs. 14: L3, Current input L3
6: I1, digital input 1/selection rate. 15: LN, Current input LN
7: I2, digital input 2/selection rate. 16: C, Common for current inputs
8: VL1, Voltage input L1 17: SHLD, GND for current inputs
9: VL2, Voltage input L2
1
23 4 56
7
8 9 10 11 12 13 14 15 16 17
POWER SUPPLY
INPUTS
A(+) B(-)
GND
RS485
L1 L2 L3
300V
~
Ph-NPh-Ph
520V ~
NV
L3L2 V L1 V
I1 I2
LN C SHLD
FLEX-MAG (100mV~ )
Figure 3:Terminals of the CVM-C10-FLEX.
14
CVM-C10
Instruction Manual

3.5.- CONNECTION DIAGRAM
3.5.1.- MEASURING THREEPHASE NETWORKS WITH A 4WIRE CONNECTION, CVMC10ITF AND
CVM-C10-mV MODEL.
Measurement system:
Power
Supply
VL1 VL2 VL3 N
L1
L2
L3
N
POWER SUPPLY
INPUTS
A(+) B(-)
GND
RS485
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
300V
~
Ph-NPh-Ph
520V ~
NV
L3L2 V L1 V
P1 P2 P1 P2
I1 I2
OUTPUTS
Rc R2 R1 Tc T2 T1
S0- S0+ S0+
VL1 VL2 VL3
ab
A B
ab
A B
S1 S2
P1 P2 S1 S2
P1 P2 S1 S2
P1 P2
LOAD
Figure 4: Three-Phase measuring with a 4-wire connection, CVM-C10-ITF and CVM-C10-mV model.
15
Instruction Manual
CVM-C10

3.5.2.- MEASURING THREEPHASE NETWORKS WITH A 4WIRE CONNECTION, CVMC10ITFIN
MODEL.
Measurement system:
VL1 VL2 VL3 N
L1
L2
L3
N
POWER SUPPLY
INPUTS
A(+) B(-)
GND
RS485
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
300V
~
Ph-NPh-Ph
520V ~
NVL3L2VL1V
P1 P2 P1 P2
I1 I2
OUTPUTS
Rc R2 R1
VL1 VL2 VL3
ab
A B
ab
A B
S1 S2
P1 P2 S1 S2
P1 P2 S1 S2
P1 P2 S1 S2
P1 P2
A
S1
S2
LN
P1
P2
Power
Supply
LOAD
Figure 5: Three-Phase Measuring with a 4-wire connection, CVM-C10-ITF-IN model.
16
CVM-C10
Instruction Manual

3.5.3.- MEASURING THREEPHASE NETWORKS WITH A 4WIRE CONNECTION CVM-C10-MC MODEL.
Measurement system:
Power
Supply
VL1 VL2 VL3 N
L1
L2
L3
N
POWER SUPPLY
INPUTS
A(+) B(-)
GND
RS485
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
300V
~
Ph-NPh-Ph
520V ~
NV
L3L2 V L1 V
P1 P2 P1 P2
I1 I2
OUTPUTS
Rc R2 R1 Tc T2 T1
S0- S0+ S0+
VL1 VL2 VL3
ab
A B
ab
A B
3P1 2P1 1P1
3P2 2P2 1P2 Brown/Green
Grey/Pink
Green/White
Red/Blue
LOAD
Figure 6: Three-Phase measuring with a 4-wire connection, CVM-C10-MC model.
Note: Do not connect MC current transformers to ground.
The MC transformer secondary value is set to 0.250 A (fixed value)
17
Instruction Manual
CVM-C10

3.5.4.- MEASURING THREEPHASE NETWORKS WITH A 4WIRE CONNECTION CVM-C10-MC-IN
MODEL.
Measurement system:
VL1 VL2 VL3 N
L1
L2
L3
N
POWER SUPPLY
INPUTS
A(+) B(-)
GND
RS485
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
300V
~
Ph-NPh-Ph
520V ~
NV
L3L2 V L1 V
P1 P2 P1 P2
I1 I2
VL1 VL2 VL3
ab
A B
ab
A B
3P1 2P1 1P1
3P2 2P2 1P2
S1 S2
P1 P2
OUTPUTS
Rc R2 R1
S1
S2
LN
P1
P2
LOAD
Brown/Green
Grey/Pink
Green/White
Red/Blue
Power
Supply
Figure 7: Three-Phase measuring with a 4-wire connection, CVM-C10-MC-IN model.
Note: Do not connect MC current transformers to ground.
The MC transformer secondary value is set to 0.250 A (fixed value)
18
CVM-C10
Instruction Manual

3.5.5.- MEASURING THREEPHASE NETWORKS WITH A 4WIRE CONNECTION, CVM-C10-FLEX MO-
DEL
Measurement system:
Power
Supply
LOAD
VL1 VL2 VL3 N
L1
L2
L3
N
POWER SUPPLY
INPUTS
A(+) B(-)
GND
RS485
300V
~
Ph-NPh-Ph
520V ~
NV
L3L2 V L1 V
I1 I2
VL1 VL2 VL3
ab
A B
ab
A B
L1 L2 L3 LN C SHLD
FLEX-MAG (100mV~ )
L1 L2
L3 LN
C
SHLD
Figure 8: Three-Phase measuring with a 4-wire connection, CVM-C10-FLEX model.
It is mandatory connect the SHLD terminal of the probe.
19
Instruction Manual
CVM-C10

3.5.6.- MEASURING THREEPHASE NETWORKS WITH A 3WIRE CONNECTION, CVMC10ITF AND
CVM-C10-mV MODEL.
Measurement system:
Power
Supply
VL1 VL2 VL3
L1
L2
L3
POWER SUPPLY
INPUTS
A(+) B(-)
GND
RS485
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
300V
~
Ph-NPh-Ph
520V ~
NV
L3L2 V L1 V
P1 P2 P1 P2
I1 I2
OUTPUTS
Rc R2 R1 Tc T2 T1
S0- S0+ S0+
VL1 VL2 VL3
ab
AB
ab
A B
S1 S2
P1 P2 S1 S2
P1 P2 S1 S2
P1 P2
LOAD
Figure 9: Three-Phase measuring with a 3-wire connection, CVM-C10-ITF and CVM-C10-mV model.
20
CVM-C10
Instruction Manual