Circutor DCB-72 Aac User manual

INSTRUCTION MANUAL
(M206B01-03-20A)
AC Ammeter
DCB-72 Aac

2
DCB-72 Aac
Instruction Manual

SAFETY PRECAUTIONS
DISCLAIMER
CIRCUTOR, SA reserves the right to make modifications to the device or the unit specifications set
out in this instruction manual without prior notice.
CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device specifica-
tions and the most updated manuals.
www.circutor.com
CIRCUTOR, recommends using the original cables and accessories that are supplied
with the device.
DANGER
Warns of a risk, which could result in personal injury or material damage.
ATTENTION
Indicates that special attention should be paid to a specific point.
Follow the warnings described in this manual with the symbols shown below.
If you must handle the unit for its installation, start-up or maintenance, the following should be
taken into consideration:
Incorrect handling or installation of the unit may result in injury to personnel as well as damage to the
unit. In particular, handling with voltages applied may result in electric shock, which may cause death
or serious injury to personnel. Defective installation or maintenance may also lead to the risk of fire.
Read the manual carefully prior to connecting the unit. Follow all installation and maintenance in-
structions throughout the unit’s working life. Pay special attention to the installation standards of the
National Electrical Code.
Refer to the instruction manual before using the unit
In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can result
in injury or damage to the unit and/or installations.
CIRCUTOR, SA reserves the right to modify features or the product manual without prior notification.
3
Instruction Manual
DCB-72 Aac

CONTENTS
SAFETY PRECAUTIONS .........................................................................................................................................................3
DISCLAIMER ..........................................................................................................................................................................3
CONTENTS.............................................................................................................................................................................4
REVISION LOG .......................................................................................................................................................................5
SYMBOLS...............................................................................................................................................................................5
1. VERIFICATION UPON RECEPTION....................................................................................................................................6
2. PRODUCT DESCRIPTION .................................................................................................................................................6
3. DEVICE INSTALLATION.................................................................................................................................................... 7
3.1.- PRIOR RECOMMENDATIONS ....................................................................................................................................7
3.2.- INSTALLATION .........................................................................................................................................................8
3.3.- DEVICE TERMINALS.................................................................................................................................................9
3.4.- CONNECTION DIAGRAM......................................................................................................................................... 10
4. OPERATION.....................................................................................................................................................................11
4.1.- DISPLAY ..................................................................................................................................................................11
4.2.- KEYBOARD FUNCTIONS ..........................................................................................................................................11
4.3.- RELAY OUTPUTS .................................................................................................................................................. 12
4.4.- DISPLAY................................................................................................................................................................. 12
5. CONFIGURATION ........................................................................................................................................................... 13
5.1.- CONFIGURATION OF THE INPUT ............................................................................................................................ 15
5.1.1.- PRIMARY CURRENT....................................................................................................................................... 16
5.1.2.- UNITS OF THE PRIMARY CURRENT .............................................................................................................. 16
5.1.3.- SECONDARY CURRENT ................................................................................................................................. 17
5.1.4.- UNITS OF THE SECONDARY CURRENT ......................................................................................................... 17
5.1.5.- SAVE CONFIGURATION .................................................................................................................................. 17
5.2.- RELAY OUTPUT 1 ................................................................................................................................................... 18
5.2.1.- RELAY MODE................................................................................................................................................. 19
5.2.2.- RELAY PULSE DURATION.............................................................................................................................. 19
5.2.3.- ALARM PARAMETER ....................................................................................................................................20
5.2.4.- CONNECTION DELAY.....................................................................................................................................20
5.2.5.- ALARM VALUE .............................................................................................................................................. 21
5.2.6.- HYSTERESIS.................................................................................................................................................. 21
5.2.7.- SAVE CONFIGURATION ..................................................................................................................................22
5.3.- RELAY OUTPUT 2 ..................................................................................................................................................22
5.4.- CONFIGURATION OF THE DISPLAY.........................................................................................................................23
5.4.1.- PASSWORD OFF ACCESS ...............................................................................................................................23
5.4.2.- BRIGHTNESS OF THE DISPLAY.....................................................................................................................24
5.4.3.- LIGHT ALARM ..............................................................................................................................................24
5.4.4.- SAVE CONFIGURATION..................................................................................................................................25
5.5.- SOFTWARE VERSION.............................................................................................................................................25
6. TECHNICAL FEATURES..................................................................................................................................................26
7. MAINTENANCE AND TECHNICAL SERVICE....................................................................................................................28
8. GUARANTEE ..................................................................................................................................................................28
9. CE CERTIFICATE ............................................................................................................................................................29
ANNEX A. CONFIGURATION MENU....................................................................................................................................32
A.1.- DCB-72 Aac ...........................................................................................................................................................32
A.2.- DCB-72 Aac WITH RELAYS....................................................................................................................................33
4
DCB-72 Aac
Instruction Manual

REVISION LOG
Table 1: Revision log.
Date Revision Description
06/18 M206B01-03-18A Initial Version
12/18 M206B01-03-18B Changes in the following sections:
3.3.- 3.4.- 4.3.- 9.- Annex A
04/19 M206B01-03-19A Changes in the following sections:
2.- 5.1.3.- Annex A
11/20 M206B01-03-20A Changes in the following sections:
3.3.- 4.3.- 5.2.5.- 5.2.6.
Note: Devices images are for illustrative purposes only and may differ from the actual device.
SYMBOLS
Table 2: Symbols.
Symbol Description
In compliance with the relevant European directive.
Device covered by European directive 2012/19/EC. At the end of its useful life,
do not leave the unit in a household waste container. Follow local regulations on
electronic equipment recycling.
DC current
~AC current
5
Instruction Manual
DCB-72 Aac

1. VERIFICATION UPON RECEPTION
Check the following points when you receive the device:
a) The device meets the specifications described in your order.
b) The device has not suffered any damage during transport.
c) Perform an external visual inspection of the device prior to switching it on.
d) Check that it has been delivered with the following:
- An installation guide,
If any problem is noticed upon reception, immediately contact the transport com-
pany and/or CIRCUTOR's after-sales service.
2. PRODUCT DESCRIPTION
The DCB-72 Aac is a device designed to measure and display the current and frequency AC sin-
gle-phase. The device has 2 programmable current scales: 1 A and 5 A.
The device features:
- 4 keys that allow you to browse between the various screens and program the device.
- LED display, displays all parameters.
- 2 fully programmable relay outputs (depending on the model).
Table 3:DCB-72 Aac list of models.
Model Power Supply Relays
80 ... 270 V ~ 80 ... 270 V 18 .. 36 V
M22250   - -
M22252   -
M222500030000 - - -
M222520030000 - -  
6
DCB-72 Aac
Instruction Manual

3. DEVICE INSTALLATION
3.1.- PRIOR RECOMMENDATIONS
In order to use the device safely, it is critical that individuals who handle it follow the
safety measures set out in the standards of the country where it is being used, use the
necessary personal protective equipment, and pay attention to the various warnings
indicated in this instruction manual.
The DCB-72 Aac device must be installed by authorised and qualified staff.
The power supply plug must be disconnected and measuring systems switched off before handling, al-
tering the connections or replacing the device. It is dangerous to handle the device while it is powered.
Also, it is critical to keep the cables in perfect condition in order to avoid accidents, personal injury and
damage to installations.
The device’s functionality is limited to the category of measuring voltage or specific current values.
The manufacturer of the device is not responsible for any damage resulting from failure by the user
or installer to heed the warnings and/or recommendations set out in this manual, nor for damage
resulting from the use of non-original products or accessories or those made by other manufacturers.
If an anomaly or malfunction is detected in the device, do not use it to take any measurements.
Disconnect the device from the power supply (device and measuring system power
supply) before maintaining, repairing or handling the device's connections.
Please contact the after-sales service if you suspect that there is an operational fault
in the device.
7
Instruction Manual
DCB-72 Aac

3.2.- INSTALLATION
Terminals, opening covers or removing elements can expose parts that are hazard-
ous to the touch while the device is powered. Do not use the device until it is fully
installed.
The device should be installed inside an electric panel or enclosure, and panel-mounted.
To install it, take the following steps:
1.- Make a cut in the panel, according to the dimensions in Figure 1.
67
67
Figure 1: Cut in the panel.
2.- Remove the device’s fixing clips (Figure 2).
Clip de jación / Fixing clip
Figure 2: Installation.
3.- Insert the device into the cut in the panel.
4.- Fit the fixing clips until the device is fixed to the panel.
The device should be connected to a power circuit protected by a fuse with a maximum nominal cur-
rent of 0.25 A.
8
DCB-72 Aac
Instruction Manual

3.3.- DEVICE TERMINALS
Version 1.0:
Table 4:List of terminals of the DCB-72 Aac (Version 1.0).
Device terminals
1: L, Power supply. 28 (1):Alarm output 1, relay (Common)
2: N, Power supply. 29 (1): Alarm output 1, relay (NO)
4: Current measurement input 31 (1): Alarm output 2, relay (Common)
5: Current measurement input 32 (1): Alarm output 2, relay (NO)
Version 2.0:
Table 5:List of terminals of the DCB-72 Aac (Version 2.0).
Device terminals
1 : L, Power supply. 28 (1): Alarm output 1, relay (NO)
2: N, Power supply. 31 (1): Alarm output 1 and 2, relay (Common)
4: Current measurement input
5: Current measurement input 32 (1): Alarm output 2, relay (NO)
(1) Available for models: M22252 y M222520030000.
54
28 29 31 32
1 2
54
28 29 31 32
12
54
28 31 32
1 2
54
28 31 32
12
Version 1.0 Version 2.0
Figure 3:Terminals of the DCB-72 Aac.
Note: Before disconnecting the current measurement connection cables, make sure that you disconnect
the transformer’s primary cable and bridge the secondary.
9
Instruction Manual
DCB-72 Aac

3.4.- CONNECTION DIAGRAM
54
28 31 32
1 2
Alimentación Auxiliar
Power Supply
I
S1S2
P1
P2
Figure 4: Current measurement DCB-72 Aac.
If the current being measured is higher than the nominal input current, 5A, a current transformer
should be connected to the device.
If more than one device is connected to the current transformer, it is necessary to connect them in
series.
10
DCB-72 Aac
Instruction Manual

4. OPERATION
4.1.- DISPLAY
The device features a 5-digit LED display, which is used to display the measured parameters and to
configure these parameters
1000.0
Keyboard
Display
Figure 5: Display DCB-72.
4.2.- KEYBOARD FUNCTIONS
The DCB-72 Aac features 4 keys to display and configure the device, Figure 5.
Table 6: Keyboard functions.
Key Keystroke
Previous screen
In the configuration menu:
Scroll through the digits
Next screen
In the configuration menu:
Increase the value of the digit
Long keystroke (> 3s):
Enter in configuration menu
In the configuration menu:
Jump to the next level/Confirm an operation
11
Instruction Manual
DCB-72 Aac

4.3.- RELAY OUTPUTS
Note: only available for models: M22252, and M222520030000.
The device features two programmable relay outputs (terminals 28, 29, 31 and 32 in Table 4,terminals
28, 31 and 32, as shown in Table 5) that can be programmed as remote control signals or alarms in the
setup menu (“5.2.- RELAY OUTPUT 1” and “5.3.- RELAY OUTPUT 2”).
4.4.- DISPLAY
The DCB-72 Aac features 2 or 3 display screens, Table 7.
Table 7: Display menu.
Display menu
5.000
Current
F
50.0
Frequency
Note: only available for models with relay outputs..
do
12
Status of the relay outputs:
1,status of the relay output 1: flashes when the relay is activated
2, status of the relay output 1: flashes when the relay is activated
If the current value measured by the device is higher than a % of the nominal value, the device can
make the digits on the display start flashing, in the form of a light alarm. See “5.4.3.- LIGHT ALARM”
12
DCB-72 Aac
Instruction Manual

5. CONFIGURATION
Press and hold the key for more than 3 seconds to enter the configuration menu of the device.
The configuration of the device is organized in different menus, Figure 6.
5.000
rEAd
inPt
do-1
do-2
SEt
uEr
>3s
ProG
Conguration
of the input
Relay output 1(2)
Relay output 2(2)
Conguration
of the display
Software version
Figure 6: Configuration menu of the DCB-72 Aac.
(2) Only available for models with relay outputs.
From any screen of the configuration menus, if no key is pressed for 4 minutes, the device leaves the
configuration menu and returns to the display screen.
Note: In “ANNEX A. CONFIGURATION MENU” you can see the complete configuration menu.
13
Instruction Manual
DCB-72 Aac

On the rEAd screen, press the ,key to access the configuration menu in the display mode, i.e.,
the configuration parameters cannot be modified.
On the rEAd screen, press the or , keys to access the configuration menu in the program-
ming mode, i.e., the configuration parameters can be modified.
rEAd ProG CodE 0000
inPt
Figure 7: Access the configuration menu in the programming mode.
Before accessing the configuration menu, it is necessary to enter the access password.
CodE 0000
Figure 8: Access password.
Use the , key to modify the value of the flashing digit
When the desired value is shown on the screen, press the key to skip the digit.
Default password: 0001
Note: The password can be modified, see “5.4.1.- PASSWORD OF ACCESS”.
To validate the data, press the key.
If the password entered is incorrect, the Err message will appear for a few seconds and the device
will return to the password configuration screen, Figure 8.
14
DCB-72 Aac
Instruction Manual

5.1.- CONFIGURATION OF THE INPUT
Figure 9, shows the main screen of the input configuration menu, from which the primary current and
secondary current are configured.
inPt
Figure 9: Input configuration menu, main screen.
Press the key to open the configuration menu.
inPt
in i
Unt. i
in 2
Unt.2
000.0
oFF
5.000
oFF
Figure 10:Input configuration menu.
15
Instruction Manual
DCB-72 Aac

5.1.1.- PRIMARY CURRENT
This screen is used to configure the value of the primary current.
in i 000.0
Use the , key to modify the value of the flashing digit
When the desired value is shown on the screen, press the key to skip the digit.
When you reach the last digit and press the key, you select the position of the decimal point. Use
the to modify the decimal point.
Minimum configuration value: 0.
Maximum configuration value: 9999.
To validate the data, press the key.
Use the and keys to browse the configuration screens of the menu.
5.1.2.- UNITS OF THE PRIMARY CURRENT
This screen is used to configure the units of the primary current.
Unt. i oFF
Use the ,key to browse the different options:
oFF, the unit of the primary current is A.
on, the unit of the primary current is kA.
To validate the data, press the key.
Use the and keys to browse the configuration screens of the menu.
16
DCB-72 Aac
Instruction Manual

5.1.3.- SECONDARY CURRENT
This screen is used to configure the value of the secondary current.
in 2 5.000
Use the and keys at the same time to configure the value.
Use the ,key to browse the different options.
5.000, for the current scale of 0 ... 5 A.
1.000, for the current scale of 0 ... 1 A.
To validate the data, press the key.
Use the and keys to browse the configuration screens of the menu.
5.1.4.- UNITS OF THE SECONDARY CURRENT
Note: This parameter cannot be modified.
Unt.2 oFF
Use the and keys to browse the configuration screens of the menu.
5.1.5.- SAVE CONFIGURATION
To save the configuration of the device, press the key, until the main screen of the input config-
uration menu is opened, Figure 9.
Press the key again to show the validation screen.
SAuE no
Use the ,key to browse the different options:
no, exit the configuration without saving the changed values.
YES, save the changed configuration values.
Press the key to validate the data and exit the configuration menu.
17
Instruction Manual
DCB-72 Aac

5.2.- RELAY OUTPUT 1
Note: Only available for models with relay outputs.
Figure 11, shows the main screen of the configuration menu of relay output 1.
do-1
Figure 11: Configuration menu of relay output 1, main screen.
Press the key to open the setup menu.
do-1
ñnodE
ñ-
tinE
itEn
dELy
HyS
uALE
ñ-
ñ-
000.0
0000
0010
oFF
000.5
i--H
Figure 12:Configuration menu of relay output 1.
18
DCB-72 Aac
Instruction Manual

5.2.1.- RELAY MODE
This screen is used to configure the operating mode of relay 1.
ñnodE oFF
ñ-
Use the key to browse the different options:
oFF, relay output 1 is disabled.
rEn, remote control output. Note: This option is only available in devices with communication.
ALr, alarm output.
To validate the data, press the key.
Use the and keys to browse the configuration screens of the menu.
5.2.2.- RELAY PULSE DURATION
The alarm relay can behave in 2 different ways:
1.- The relay is activated when the alarm is triggered and is deactivated when the alarm is de-
activated.
2.- The relay is activated when the alarm is triggered and is deactivated after a programmed
period of time, even though the alarm condition has not been cancelled.
This screen is used to configure the programmed time, i.e., the relay pulse duration.
To make the relay operate in mode no. 1, program the value to 0.
tinE 0000
ñ-
Use the , key to modify the value of the flashing digit
When the desired value is shown on the screen, press the key to skip the digit.
Minimum configuration value: 0 x 0.1 s
Maximum configuration value: 9999 x 0.1 s
Example: Use program 0050 to configure a value of 5 s.
To validate the data, press the key.
Use the and keys to browse the configuration screens of the menu.
-
19
Instruction Manual
DCB-72 Aac

5.2.3.- ALARM PARAMETER
This screen is used to configure the parameter that will be used to activate the alarm.
itEn i--H
ñ-
Use the key to browse the different options:
F--H, Active alarm when the frequency is higher than the alarm value.
I--H, Active alarm when the current is higher than the alarm value.
F--L, Active alarm when the frequency is less than the alarm value.
I--L, Active alarm when the current is less than the alarm value.
To validate the data, press the key.
Use the and keys to browse the configuration screens of the menu.
5.2.4.- CONNECTION DELAY
This screen is used to configure the alarm connection delay.
dELy 0010
Use the , key to modify the value of the flashing digit
When the desired value is shown on the screen, press the key to skip the digit.
Minimum configuration value: 0 x 0.1 s
Maximum configuration value: 9999 x 0.1 s
Example: Use program 0050 to configure a value of 5 s.
To validate the data, press the key.
Use the and keys to browse the configuration screens of the menu.
20
DCB-72 Aac
Instruction Manual