Circutor CVM-D41 DC User manual

INSTRUCTION MANUAL
Power analyzer
CVM-D41 DC
(M337B01-03-21A)

2
CVM-D41 DC
Instruction Manual

3
Instruction Manual
CVM-D41 DC
SAFETY PRECAUTIONS
DANGER
Warns of a risk, which could result in personal injury or material damage.
ATTENTION
Indicates that special attention should be paid to a specific point.
Follow the warnings described in this manual with the symbols shown below.
If you must handle the unit for its installation, start-up or maintenance, the following should be
taken into consideration:
Incorrect handling or installation of the unit may result in injury to personnel as well as damage to the
unit. In particular, handling with voltages applied may result in electric shock, which may cause death
or serious injury to personnel. Defective installation or maintenance may also lead to the risk of fire.
Read the manual carefully prior to connecting the unit. Follow all installation and maintenance in-
structions throughout the unit’s working life. Pay special attention to the installation standards of the
National Electrical Code.
Refer to the instruction manual before using the unit
In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can result
in injury or damage to the unit and/or installations.
CIRCUTOR, SA reserves the right to modify features or the product manual without prior notification.
DISCLAIMER
CIRCUTOR, SA reserves the right to make modifications to the device or the unit specifications set
out in this instruction manual without prior notice.
CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device specifica-
tions and the most updated manuals.
www.circutor.com
CIRCUTOR, recommends using the original cables and accessories that are supplied
with the device.

4
CVM-D41 DC
Instruction Manual
CONTENTS
SAFETY PRECAUTIONS .........................................................................................................................................................3
DISCLAIMER ..........................................................................................................................................................................3
CONTENTS.............................................................................................................................................................................4
REVISION LOG .......................................................................................................................................................................6
SYMBOLS...............................................................................................................................................................................6
1. VERIFICATION UPON RECEPTION ....................................................................................................................................7
2. PRODUCT DESCRIPTION .................................................................................................................................................7
3. DEVICE INSTALLATION................................................................................................................................................... 8
3.1.- PRIOR RECOMMENDATIONS ................................................................................................................................... 8
3.2.- INSTALLATION ....................................................................................................................................................... 8
3.3.- DEVICE TERMINALS.................................................................................................................................................9
3.4.- CONNECTION DIAGRAM.........................................................................................................................................10
3.4.1.- SIMULTANEOUS VOLTAGE AND CURRENT MEASUREMENT...........................................................................10
3.4.2.- VOLTAGE MEASUREMENT ...............................................................................................................................11
3.4.3.- CURRENT MEASUREMENT ............................................................................................................................ 12
4. OPERATION.................................................................................................................................................................... 13
4.1.- DISPLAY ................................................................................................................................................................. 13
4.2.- KEYBOARD FUNCTIONS ......................................................................................................................................... 13
4.3.- LEDs ...................................................................................................................................................................... 14
4.4.- RELAY OUTPUTS ................................................................................................................................................... 14
4.5.- ANALOG OUTPUT ..................................................................................................................................................15
4.6.- DIGITAL INPUTS ...................................................................................................................................................15
4.7.- DISPLAY .................................................................................................................................................................15
4.7.1.- MAXIMUM & MINIMUM VALUES......................................................................................................................16
4.7.2.- TOTALISERS..................................................................................................................................................... 17
5. CONFIGURATION ...........................................................................................................................................................18
5.1.- CONFIGURATION OF THE INPUT ........................................................................................................................... 20
5.1.1.- VOLTAGE DISPLAY VALUE................................................................................................................................ 20
5.1.2.- VOLTAGE MEASUREMENT RANGE ................................................................................................................... 21
5.1.3.- CURRENT DISPLAY VALUE.............................................................................................................................. 21
5.1.4.- CURRENT INPUT..............................................................................................................................................22
5.1.5.- DECIMAL POINT FOR DISPLAYING VOLTAGE ...................................................................................................22
5.1.6.- SAVE CONFIGURATION ....................................................................................................................................23
5.2.- RS-485 COMMUNICATIONS...................................................................................................................................23
5.2.1.- MODBUS ADDRESS .........................................................................................................................................24
5.2.2.- BAUD RATE .....................................................................................................................................................24
5.2.3.- DATA FORMAT.................................................................................................................................................24
5.2.4.- SAVE CONFIGURATION....................................................................................................................................25
5.3.- ANALOG OUTPUT ..................................................................................................................................................25
5.3.1.- TYPE OF OUTPUT........................................................................................................................................... 26
5.3.2.- ANALOG OUTPUT PARAMETER..................................................................................................................... 26
5.3.3.- READING FOR THE START OF THE ANALOG OUTPUT .....................................................................................27
5.3.4.-READING FOR THE END OF THE ANALOG OUTPUT .........................................................................................27
5.3.5.- SAVE CONFIGURATION................................................................................................................................... 28
5.4.- RELAY OUTPUT 1 .................................................................................................................................................. 29
5.4.1.- RELAY MODE.................................................................................................................................................. 29
5.4.2.- RELAY PULSE DURATION ............................................................................................................................... 30
5.4.3.- ALARM PARAMETER ..................................................................................................................................... 30
5.4.4.- CONNECTION DELAY ....................................................................................................................................... 31
5.4.5.- ALARM VALUE................................................................................................................................................. 31
5.4.6.- HYSTERESIS....................................................................................................................................................32
5.4.7.- SAVE CONFIGURATION ...................................................................................................................................32
5.5.- RELAY OUTPUT 2 .................................................................................................................................................32
5.6.- CONFIGURATION OF THE DISPLAY ........................................................................................................................33
5.6.1.- LOGIN PASSWORD ...........................................................................................................................................34
5.6.2.- CYCLIC DISPLAY .............................................................................................................................................34
5.6.3.- BACKLIGHT OF THE DISPLAY .........................................................................................................................34
5.6.4.- LIGHT ALARM ................................................................................................................................................ 35
5.6.5.-DISPLAY HOME SCREEN................................................................................................................................. 35

5
Instruction Manual
CVM-D41 DC
5.6.6.- REFRESH TIME ...............................................................................................................................................36
5.6.7.- DELETING THE MAXIMUM & MINIMUM VALUES .............................................................................................36
5.6.8.- DELETING THE ELECTRICAL CHARGE TOTALISERS ........................................................................................36
5.6.9.- DELETING THE ENERGY TOTALISERS..............................................................................................................37
5.6.10.- SAVE CONFIGURATION .................................................................................................................................37
5.7.- SOFTWARE VERSION .............................................................................................................................................37
6. RS485 COMMUNICATIONS ......................................................................................................................................... 38
6.1.- CONNECTIONS ...................................................................................................................................................... 38
6.2.- MODBUS PROTOCOL..............................................................................................................................................39
6.2.1. READING EXAMPLE: FUNCTION 0x01...............................................................................................................39
6.2.2. EXAMPLE OF OPERATION OF THE REMOTE CONTROL: FUNCTION 0x05. ......................................................39
6.3.- MODBUS COMMANDS .......................................................................................................................................... 40
6.3.1.- MEASUREMENT VARIABLES AND DEVICE STATUS ........................................................................................ 40
6.3.2.- RELAY OUTPUTS ............................................................................................................................................. 41
6.3.3.- DIGITAL INPUTS .............................................................................................................................................. 41
6.3.4.- REMOTE CONTROL OUTPUT (Relay output)...................................................................................................42
6.3.5.- DELETING VALUES..........................................................................................................................................42
6.3.6.- DEVICE CONFIGURATION VARIABLES .............................................................................................................43
7. TECHNICAL FEATURES ..................................................................................................................................................46
8. MAINTENANCE AND TECHNICAL SERVICE ...................................................................................................................49
9. GUARANTEE ..................................................................................................................................................................49
10. CE CERTIFICATE.......................................................................................................................................................... 50
ANNEX A. CONFIGURATION MENU....................................................................................................................................53

6
CVM-D41 DC
Instruction Manual
REVISION LOG
Table 1: Revision log.
Date Revision Description
04/22 M337B01-03-21A Initial version
Note: Devices images are for illustrative purposes only and may differ from the actual device.
SYMBOLS
Table 2: Symbols.
Symbol Description
In compliance with the relevant European directive.
Device covered by European directive 2012/19/EC. At the end of its useful life, do not leave the
unit in a household waste container. Follow local regulations on electronic equipment recycling.
DC current
~AC current

7
Instruction Manual
CVM-D41 DC
1. VERIFICATION UPON RECEPTION
Check the following points when you receive the device:
a) The device meets the specifications described in your order.
b) The device has not suffered any damage during transport.
c) Perform an external visual inspection of the device prior to switching it on.
d) Check that it has been delivered with the following:
- An installation guide,
If any problem is noticed upon reception, immediately contact the transport com-
pany and/or CIRCUTOR’s after-sales service.
2. PRODUCT DESCRIPTION
The CVM-D41 DC is designed to measure and display the DC voltage, DC current, power, energy and
electric charge.
The device features:
- 4 keys that allow you to browse between the various screens and program the device.
- LED display, displays all parameters.
- 2 fully programmable relay outputs
- 2 digital inputs.
- 1 programmable analog output, voltage or current.
- Communications RS-485.
CIRCUTOR has different models, see Table 3.
Table 3: CVM-D41 DC Models.
Model Power Supply Analog output
100 ... 270 V ~ 100 ... 270 V 20 ... 60 V V A
CVM-D41 DC
M56638   - - 
M566380040000 - - -
M5663A   --
M5663A0040000 - -   -

8
CVM-D41 DC
Instruction Manual
3. DEVICE INSTALLATION
3.1.- PRIOR RECOMMENDATIONS
In order to use the device safely, it is critical that individuals who handle it follow the
safety measures set out in the standards of the country where it is being used, use the
necessary personal protective equipment, and pay attention to the various warnings
indicated in this instruction manual.
The CVM-D41 DC device must be installed by authorised and qualified staff.
The power supply plug must be disconnected and measuring systems switched off before handling, al-
tering the connections or replacing the device. It is dangerous to handle the device while it is powered.
Also, it is critical to keep the cables in perfect condition in order to avoid accidents, personal injury and
damage to installations.
The device’s functionality is limited to the category of measuring voltage or specific current values.
The manufacturer of the device is not responsible for any damage resulting from failure by the user
or installer to heed the warnings and/or recommendations set out in this manual, nor for damage
resulting from the use of non-original products or accessories or those made by other manufacturers.
If an anomaly or malfunction is detected in the device, do not use it to take any measurements.
Disconnect the device from the power supply (device and measuring system power
supply) before maintaining, repairing or handling the device’s connections.
Please contact the after-sales service if you suspect that there is an operational fault
in the device.
3.2.- INSTALLATION
Terminals, opening covers or removing elements can expose parts that are hazard-
ous to the touch while the device is powered. Do not use the device until it is fully
installed.
The device should be installed inside an electric panel or enclosure, attached to a DIN rail (IEC 60715).
The device should be connected to a power circuit protected by a fuse with a maximum nominal cur-
rent of 0.25 A.

9
Instruction Manual
CVM-D41 DC
3.3.- DEVICE TERMINALS
1 2 11 5 4
Figure 1: CVM-D41 DC terminals (Upper).
Table 4: CVM-D41 DC terminals (Upper).
Device terminals
1: L, Power supply 5: IU-, Current measurement input/
Voltage measurement input
2: N, Power supply 4: I +, Current measurement input
11: U+, Voltage measurement input
28 29 31 32
15 16 58 59 70 71 72
Figure 2: CVM-D41 DC terminals (down).
Table 5: CVM-D41 DC terminals (down).
Device terminals
28: R01, Relay output 1 (Common) 58: A, RS-485
29: R01, Relay output 1 (NO) 59: B, RS-485
31: R02, Relay output 2 (Common) 70: DIC, Common digital inputs
32: R02, Relay output 2 (NO) 71: 1, Digital input 1
15: +AO, Analog output 72: 2, Digital input 2
16:-A0, Analog output

10
CVM-D41 DC
Instruction Manual
3.4.- CONNECTION DIAGRAM
3.4.1.- SIMULTANEOUS VOLTAGE AND CURRENT MEASUREMENT
1
2
U+
595828 29 31 32 1615
-+
BA
RS-485
DIC 12
RO1 R02
+
-
Digital inputs
Entradas Digitales
Analog output
Salida Analógica
Alimentación Auxiliar
Power Supply
Relay output
Salida de relés
Load
Carga
I
Shunt
-
+
45
11
70 71 72
IU
L
N
A0
Figure 3: Voltage and current measurement.
Make sure that the positive and negative voltage terminals are as shown in the connection diagram.

11
Instruction Manual
CVM-D41 DC
3.4.2.- VOLTAGE MEASUREMENT
1
2
U+
595828 29 31 32 1615
-+
BA
RS-485
DIC 12
RO1 R02
+
-
Digital inputs
Entradas Digitales
Analog output
Salida Analógica
Alimentación Auxiliar
Power Supply
Relay output
Salida de relés
Load
Carga
-
45
11
70 71 72
L
N
A0
I+IU
Figure 4: Voltage measurement.
Note: To keep noise from appearing on the current screen, we recommend installing a jumper between
terminals 4 and 5.

12
CVM-D41 DC
Instruction Manual
3.4.3.- CURRENT MEASUREMENT
1
2
595828 29 31 32 1615
-+
BA
RS-485
DIC 12
RO1 R02
+
-
Digital inputs
Entradas Digitales
Analog output
Salida Analógica
Alimentación Auxiliar
Power Supply
Relay output
Salida de relés
Load
Carga
I
Shunt
-
+
45
70 71 72
IU
L
N
A0
Figure 5: Current measurement.

13
Instruction Manual
CVM-D41 DC
4. OPERATION
4.1.- DISPLAY
The device features a 5-digit LED display, which is used to display the measured parameters and to
configure these parameters
Status
Digital inputs
Status
Relay outputs
Units
Configuration
RS-485
Communications
00000
DI
1
1
2
2
D0
k W h
Figure 6: CVM-D41 DC display.
The display also shows:
The status of the digital inputs, if an input is connected, its corresponding number flashes.
The status of the relay outputs, if a relay is closed, its corresponding number flashes.
4.2.- KEYBOARD FUNCTIONS
The CVM-D41 DC features 4 keys to display and configure the device, Figure 7 and Table 6.
AL1 AL2
LEDs
Keyboard
Figure 7:CVM-D41 DC Keyboard and LEDs.
Table 6: Keyboard functions.
Key Keystroke
Previous screen
In the configuration menu:
Scroll through the digits
Next screen
In the configuration menu:
Increase the value of the digit

14
CVM-D41 DC
Instruction Manual
Table 6 (Continuation): Keyboard functions.
Key Keystroke
Long keystroke (> 3s):
Enter in configuration menu
In the configuration menu:
Jump to the next level/Confirm an operation
4.3.- LEDs
The device has 2 LEDs, AL1 and AL2 (Figure 7) that are activated when Alarm 1 (AL1) is activated and
Alarm 2 (AL2). The alarms on the device are configured in the settings menu: “5.4 - RELAY OUTPUT 1”
and “5.5 - RELAY OUTPUT 2”.
4.4.- RELAY OUTPUTS
The device features two programmable relay outputs (terminals 28, 29, 31 and 32, as shown in Figure 8)
that can be programmed as remote control signals or alarms in the setup menu (“5.4.- RELAY OUTPUT
1” and “5.5.- RELAY OUTPUT 2”).
1
2
U+
595828 29 31 32 1615
-+
BA
RS-485
DIC 12
RO1 R02
+
-
Digital inputs
Entradas Digitales
Analog output
Salida Analógica
Alimentación Auxiliar
Power Supply
Relay output
Salida de relés
Load
Carga
I
Shunt
-
+
45
11
70 71 72
IU
L
N
A0
Figure 8: Relay outputs, digital inputs and Analog output.

15
Instruction Manual
CVM-D41 DC
4.5.- ANALOG OUTPUT
The device has an analog output (terminals 15 and 16 of Figure 8) programmable through the config-
uration menu (“5.3.- ANALOG OUTPUT”)
The analog output can be voltage or current, depending on the device model, Table 7:
Table 7:Device model depending on the analog output..
Model Analog output
Voltage Current
CVM-D41 DC
M56638 -
M566380040000 -
M5663A -
M5663A0040000 -
4.6.- DIGITAL INPUTS
The device has two digital inputs (terminals 70, 71 and 72 of Figure 8).The relay outputs can be activat-
ed depending on the value of the digital inputs (See “5.4.- RELAY OUTPUT 1” and “5.5.- RELAY OUTPUT 2”)
4.7.- DISPLAY
The CVM-D41 DC features 7 display screens, Table 8. Use keys and to browse through the
different screens.
The display screens can change automatically depending on the time programmed in section "5.6.2.-
CYCLIC DISPLAY".
Table 8: Display menu.
Display menu
1000
DI
1
1
2
2
D0
V
Voltage
500
DI
1
1
2
2
D0
A
.
Current
5003
DI
1
1
2
2
D0
k W
.
Power

16
CVM-D41 DC
Instruction Manual
Table 8: (Continued): Display menu.
Display menu
28347
DI
1
1
2
2
D0
k W h
.
Positive energy
03607
DI
1
1
2
2
D0
k W h
.
-
Negative energy
00047
DI
1
1
2
2
D0
A h
.
Positive electric charge
00007
DI
1
1
2
2
D0
A h
.
-
Negative electric charge
The home screen, meaning the first screen displayed when powering up the device or when exiting the
settings menu, can be programmed in section "5.6.5.- DISPLAY HOME SCREEN".
If the value of voltage, current or power measured by the device is % higher than the nominal value,
the device can make the digits on the display start flashing to provide a visual alarm. See “5.6.4.- LIGHT
ALARM”
4.7.1.- MAXIMUM & MINIMUM VALUES
The maximum and minimum values for the voltage, current and power parameters can be displayed
by pressing the key while the corresponding parameter is being displayed.
When the key is first pressed the minimum value is displayed and the word MIN is shown at the
top right of the display.
When the key is pressed for the second time , the maximum value is displayed and the word MAX
is shown at the top right of the display.
Press the key again to return to the instantaneous value.
The maximum and minimum values can be deleted in the settings menu ("5.6.6.- DELETING THE MAXI-
MUM AND MINIMUM VALUES") or through the communications options ("6.3.5.- DELETING VALUES").

17
Instruction Manual
CVM-D41 DC
4.7.2.- TOTALISERS
For the Positive Energy, Negative Energy, Positive Electric Charge and Negative Electric Charge pa-
rameters, the value of Energy or Electric Charge since the device was started can be viewed by pressing
the key while the corresponding parameter is being displayed.
The total value is displayed in 3 totalisers, A, Band C. When the key is first pressed, totaliser A
is displayed and the letter A is shown at the top left of the display.
Press key to view the different totalisers.
Table 9: Display range of the Totalisers.
Totaliser Display range
C0... 9.999 k W/Ah
B10 k W/Ah ... 99.99 M W/Ah
A100 M W/Ah ... 999.9 G W/Ah
The totalisers can be cleared in the settings menu ("5.6.8.- DELETING THE ELECTRIC CHARGE TOTALISERS"
and "5.6.9.- DELETING THE ENERGY TOTALISERS") or through the communications options ("6.3.5.- DE-
LETING VALUES").

18
CVM-D41 DC
Instruction Manual
5. CONFIGURATION
Press and hold the key for more than 3 seconds to enter the configuration menu of the device.
The configuration of the device is organized in different menus, Figure 9.
do-1
>3s
ñ-ñ-
Conguration of
the input
Relay output 1
Relay output 2
Conguration of
the display
Software version
Communications
Analog output
Ao-1
1000
DI
1
1
2
2
D0
V
rEAd ProG
inpt
Conn
do-2
SEt
uEr
Figure 9: CVM-D41 DC configuration menu.
From any screen of the configuration menus, if no key is pressed for 4 minutes, the device leaves the
configuration menu and returns to the display screen.
Note: In “ANNEX A. CONFIGURATION MENU”you can see the complete configuration menu.

19
Instruction Manual
CVM-D41 DC
On the REAd screen, press the ,key to access the configuration menu in the display mode, i.e.,
the configuration parameters cannot be modified.
On the REAd screen, press the or keys to access the configuration menu in the program-
ming mode, i.e., the configuration parameters can be modified.
ProG CodE 0000
inPt
rEAd
Figure 10: Access the configuration menu in the programming mode.
Before accessing the configuration menu, it is necessary to enter the login password.
CodE 0000
Figure 11: Login password.
Use the , key to modify the value of the flashing digit
When the desired value is shown on the screen, press the key to skip the digit.
Default password: 0001
Note: The password can be modified, see "5.6.1 .- LOGIN PASSWORD" .
To validate the data, press the key.
If the password entered is incorrect, the Err message will appear for a few seconds and the device
will return to the password configuration screen, Figure 11.

20
CVM-D41 DC
Instruction Manual
5.1.- CONFIGURATION OF THE INPUT
Figure 12 shows the main screen of the input configuration menu, where the input measurement range
and the display value are configured.
inPt
Figure 12: Input configuration menu, main screen.
Press the key to open the configuration menu.
75.00
75.00
A
000.0
inPt
Pt-1
Pt-2
Ct-1
Ct-2
1000
150.0
V
V
mV
Poin
Figure 13: Input configuration menu.
5.1.1.- VOLTAGE DISPLAY VALUE
This screen is used to configure the voltage value to display when the maximum value of the voltage
measurement range is input to the device.
Pt-1 1000V
Use the , key to modify the value of the flashing digit