Circutor CVM-B150-ITF-HF User manual

INSTRUCTION MANUAL
(M210B01-03-23A)
Power analyzer
CVM-B150-ITF-HF
MEASURING EQUIPMENT
E237816

2
CVM-B150-ITF-HF
Instruction Manual

SAFETY PRECAUTIONS
DISCLAIMER
CIRCUTOR S.A.U. reserves the right to make modifications to the device or the unit specifications set
out in this instruction manual without prior notice.
CIRCUTOR S.A.U. on its web site, supplies its customers with the latest versions of the device specifi-
cations and the most updated manuals.
www.circutor.com
CIRCUTOR S.A.U. recommends using the original cables and accessories that are sup-
plied with the device.
DANGER
Warns of a risk, which could result in personal injury or material damage.
ATTENTION
Indicates that special attention should be paid to a specific point.
Follow the warnings described in this manual with the symbols shown below.
If you must handle the unit for its installation, start-up or maintenance, the following should be
taken into consideration:
Incorrect handling or installation of the device may result in injury to personnel as well as damage to
the device. In particular, handling with voltages applied may result in electric shock, which may cause
death or serious injury to personnel. Defective installation or maintenance may also lead to the risk of
fire.
Read the manual carefully prior to connecting the device. Follow all installation and maintenance in-
structions throughout the device’s working life. Pay special attention to the installation standards of
the National Electrical Code.
Refer to the instruction manual before using the device
In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can result
in injury or damage to the device and/or installations.
CIRCUTOR S.A.U. reserves the right to modify features or the product manual without prior notification.
3
Instruction Manual
CVM-B150-ITF-HF

CONTENTS
SAFETY PRECAUTIONS .........................................................................................................................................................3
DISCLAIMER ..........................................................................................................................................................................3
CONTENTS.............................................................................................................................................................................4
REVISION LOG .......................................................................................................................................................................7
1. VERIFICATION UPON RECEPTION....................................................................................................................................8
2. PRODUCT DESCRIPTION .................................................................................................................................................8
3. DEVICE INSTALLATION.................................................................................................................................................. 10
3.1.- PRIOR RECOMMENDATIONS ..................................................................................................................................10
3.2.- INSTALLATION .......................................................................................................................................................10
3.3.- DEVICE TERMINALS................................................................................................................................................11
3.3.1.- TERMINALS ON THE UPPER FACE ..................................................................................................................11
3.3.2. TERMINALS ON THE LOWER FACE ................................................................................................................. 12
3.4.- CONNECTION DIAGRAMS....................................................................................................................................... 13
3.4.1.- THREEPHASE NETWORK MEASUREMENT WITH A 4WIRE CONNECTION. ................................................. 13
3.4.2. THREEPHASE NETWORK MEASUREMENT WITH A 3WIRE CONNECTION. ................................................ 14
3.4.3. THREEPHASE NETWORK MEASUREMENT WITH A 3WIRE CONNECTION AND 3 VOLTAGE TRANSFORM
ERS ............................................................................................................................................................................. 15
3.4.4. THREEPHASE NETWORK MEASUREMENT WITH A 3WIRE CONNECTION AND TRANSFORMERS WITH AN
ARON CONNECTION. .................................................................................................................................................. 16
3.4.5.- TWOPHASE NETWORK MEASUREMENT WITH A 3WIRE CONNECTION. .................................................... 17
3.4.6. SINGLEPHASE NETWORK MEASUREMENT, PHASE TO PHASE, WITH A 2WIRE CONNECTION..................18
3.4.7. SINGLEPHASE NETWORK MEASUREMENT, PHASE TO NEUTRAL, WITH A 2WIRE CONNECTION.............. 19
3.5.- STARTING UP THE DEVICE ................................................................................................................................... 20
4. OPERATION ...................................................................................................................................................................26
4.1.- OPERATING PRINCIPLE ..........................................................................................................................................26
4.2.- MEASUREMENT PARAMETERS..............................................................................................................................27
4.3.- KEYPAD FUNCTIONS..............................................................................................................................................28
4.4.- DISPLAY.................................................................................................................................................................28
4.4.1.- UPPER AREA....................................................................................................................................................29
4.4.2.- LOWER AREA.................................................................................................................................................. 30
4.4.3.- CENTRAL AREA.............................................................................................................................................. 30
4.5.- LED INDICATORS....................................................................................................................................................32
4.6.- INPUTS ..................................................................................................................................................................33
4.7.- OUTPUTS ...............................................................................................................................................................33
5. DISPLAY AND CONFIGURATION ....................................................................................................................................34
5.1.-MEASUREMENT DISPLAY MENU ...........................................................................................................................35
5.1.1.- DISPLAY 1 PARAMETER. ..................................................................................................................................36
5.1.2. DISPLAY 3 PARAMETERS................................................................................................................................63
5.1.3. DISPLAY 4 PARAMETERS................................................................................................................................81
5.1.4. INTEGRATED FUNCTIONS.............................................................................................................................. 99
5.1.5. EXPANSION MODULES..................................................................................................................................100
5.2.- ENERGY CLOSES MENU ......................................................................................................................................102
5.2.1. ACTIVE ENERGY CLOSES III OF THE TOTAL TARIFF AND OF REACTIVE ENERGY III OF THE TOTAL TARIFF. 103
5.3.- ALARM MENU .....................................................................................................................................................105
5.4.- LOG MENU ......................................................................................................................................................... 107
5.4.1.- ALARM LOG...................................................................................................................................................108
5.4.2.EVENT LOG .................................................................................................................................................... 110
5.5.- INFORMATION MENU .......................................................................................................................................... 111
5.5.1.- SYSTEM INFORMATION. ................................................................................................................................112
5.5.2. INTEGRATED FUNCTIONS..............................................................................................................................113
5.5.3. EXPANSION MODULES. .................................................................................................................................114
5.5.4.- CIRCUTOR S.A.U............................................................................................................................................ 125
5.6.- SETUP MENU ...................................................................................................................................................... 126
5.6.1.- DATE AND TIME............................................................................................................................................. 129
5.6.2. TIME ZONE....................................................................................................................................................130
5.6.3. LANGUAGE.....................................................................................................................................................131
5.6.4. ACCESS KEY.................................................................................................................................................. 132
5.6.5. MEASUREMENT CONNECTION MODE.......................................................................................................... 133
5.6.6. RATIO OF VOLTAGE TRANSFORMERS........................................................................................................... 134
4
CVM-B150-ITF-HF
Instruction Manual

5.6.7.- RATIO OF CURRENT TRANSFORMERS.......................................................................................................... 135
5.6.8. INSTALLATION DATA. ................................................................................................................................... 137
5.6.9. DEMAND.......................................................................................................................................................138
5.6.10. ENERGY CONSUMPTION COSTS................................................................................................................. 139
5.6.11. ENERGY GENERATION COSTS.....................................................................................................................140
5.6.12. CO2CONSUMPTION EMISSIONS. .................................................................................................................141
5.6.13. CO2GENERATION EMISSIONS..................................................................................................................... 142
5.6.14. RELAY DIGITAL OUTPUTS........................................................................................................................... 144
5.6.15. TRANSISTOR DIGITAL OUTPUTS.................................................................................................................150
5.6.16. DIGITAL INPUTS..........................................................................................................................................155
5.6.17. INTEGRATED COMMUNICATIONS................................................................................................................159
5.6.18. PARAMETER RESET.................................................................................................................................... 162
5.6.19. USER INTERFACE........................................................................................................................................ 164
5.6.20. EXPANSION MODULES...............................................................................................................................165
6. INTEGRATED COMMUNICATIONS................................................................................................................................166
6.1.- CONNECTIONS .....................................................................................................................................................166
6.2.- MODBUS PROTOCOL............................................................................................................................................ 167
6.2.1.- EXAMPLE OF MODBUS QUERY .....................................................................................................................168
6.3.- MODBUS MEMORY MAP......................................................................................................................................168
6.3.1. MEASUREMENT VARIABLES.........................................................................................................................168
6.3.2.- CURRENT ENERGY VARIABLES .................................................................................................................... 170
6.3.3. MAXIMUM DEMAND VARIABLES ................................................................................................................. 174
6.3.4. COST VARIABLES.......................................................................................................................................... 175
6.3.5. ANGLE VARIABLES....................................................................................................................................... 175
6.3.6. DEVICE CONFIGURATION VARIABLES .......................................................................................................... 175
6.3.7. OTHER DEVICE VARIABLES .......................................................................................................................... 187
6.3.8. DELETING PARAMETERS ..............................................................................................................................191
6.4.- BACnet PROTOCOL ...............................................................................................................................................191
6.5.- PICS MAP............................................................................................................................................................. 192
7. EXPANSION MODULES.................................................................................................................................................195
7.1.- INSTALLATION ......................................................................................................................................................195
7.2.- RELAY DIGITAL INPUTS/OUTPUTS ......................................................................................................................198
7.2.1.- CONNECTION TERMINALS ............................................................................................................................198
7.2.2.- CONNECTION DIAGRAMS..............................................................................................................................199
7.2.3.- CONFIGURATION .......................................................................................................................................... 200
7.2.4.- MODBUS COMMUNICATIONS ....................................................................................................................... 204
7.3.- TRANSISTOR DIGITAL INPUTS/OUTPUTS.............................................................................................................211
7.3.1.- CONNECTION TERMINALS..............................................................................................................................211
7.3.2.- CONNECTION DIAGRAMS.............................................................................................................................. 212
7.3.3.- CONFIGURATION ........................................................................................................................................... 213
7.3.4.- COMUNICACIONES MODBUS......................................................................................................................... 215
7.4.- ANALOGUE INPUTS/OUTPUTS............................................................................................................................226
7.4.1.- CONNECTION TERMINALS.............................................................................................................................226
7.4.2.- CONNECTION DIAGRAMS............................................................................................................................. 228
7.4.3.- CONFIGURATION ...........................................................................................................................................229
7.4.4.- MODBUS COMMUNICATIONS ........................................................................................................................235
7.5.- MODBUS/TCP BRIDGE COMMUNICATIONS MODULE ......................................................................................... 240
7.5.1.- CONNECTION TERMINALS............................................................................................................................ 240
7.5.2.- LEDs ............................................................................................................................................................ 240
7.5.3.- CONNECTION DIAGRAM................................................................................................................................ 241
7.5.4.- CONFIGURATION ........................................................................................................................................... 241
7.5.5.- MODBUS COMMUNICATIONS........................................................................................................................246
7.6.- LONWORKS COMMUNICATIONS MODULE........................................................................................................... 248
7.6.1.- CONNECTION TERMINALS............................................................................................................................ 248
7.6.2.- CONNECTION DIAGRAM............................................................................................................................... 248
7.6.3.- CONFIGURATION ...........................................................................................................................................249
7.6.4.- MODBUS COMMUNICATIONS........................................................................................................................ 251
7.6.5.- LIST OF LONWORKS LOGS............................................................................................................................ 251
7.7.- PROFIBUS COMMUNICATIONS MODULE ............................................................................................................. 258
7.7.1.- CONNECTION TERMINALS ............................................................................................................................ 258
7.7.2.- LEDs ............................................................................................................................................................. 258
7.7.3.- CONNECTION DIAGRAM ............................................................................................................................... 259
5
Instruction Manual
CVM-B150-ITF-HF

7.7.4.- CONFIGURATION........................................................................................................................................... 260
7.7.5.- VARIABLES PROFIBUS GSD FILE .................................................................................................................. 261
7.8.- MBUS COMMUNICATIONS MODULE ....................................................................................................................265
7.8.1.- CONNECTION TERMINALS.............................................................................................................................265
7.8.2.- CONNECTION DIAGRAM................................................................................................................................265
7.8.3.- CONFIGURATION ...........................................................................................................................................266
7.8.4.- MODBUS COMMUNICATIONS........................................................................................................................268
7.8.5.- MBUS COMMUNICATIONS...........................................................................................................................268
7.9.- DATA STORAGE MODULE, DATALOGGER ..............................................................................................................270
7.9.1.- CONNECTION TERMINALS.............................................................................................................................270
7.9.2.- LEDs .............................................................................................................................................................270
7.9.3.- CONNECTION DIAGRAM................................................................................................................................ 271
7.9.4.- CONFIGURATION ...........................................................................................................................................272
7.9.5.- MODBUS COMMUNICATIONS........................................................................................................................276
7.10.- MODBUS/TCP Switch COMMUNICATIONS MODULE..........................................................................................277
7.10.1.- CONNECTION TERMINALS ........................................................................................................................... 277
7.10.2.- LEDs ............................................................................................................................................................ 277
7.10.3.- CONNECTION DIAGRAM ..............................................................................................................................278
7.10.4.- CONFIGURATION..........................................................................................................................................278
7.10.5.- MODBUS COMMUNICATIONS ......................................................................................................................282
8. SOFTWARE UPDATE....................................................................................................................................................283
8.1.- DEVICE SOFTWARE UPDATE................................................................................................................................284
8.2.- EXPANSION MODULES UPDATE...........................................................................................................................284
8.3.- UPGRADING THE FIRMWARE OF THE DATALOGGER MODULE ............................................................................285
9. TECHNICAL FEATURES................................................................................................................................................287
10. TECHNICAL FEATURES OF EXPANSION MODULES .................................................................................................. 290
10.1.- TRANSISTOR DIGITAL INPUTS/OUTPUTS ......................................................................................................... 290
10.2.- RELAY DIGITAL INPUTS/OUTPUTS.................................................................................................................... 291
10.3.- DIGITAL ANALOGUE INPUTS/OUTPUTS............................................................................................................292
10.4.- MODBUS TCP (Bridge) COMMUNICATIONS........................................................................................................293
10.5.- LONWORKS COMMUNICATIONS.........................................................................................................................294
10.6.- PROFIBUS COMMUNICATIONS...........................................................................................................................295
10.7.- MBUS COMMUNICATIONS ..................................................................................................................................296
10.8.- DATA STORAGE, DATALOGGER ...........................................................................................................................297
10.9.- MODBUS TCP (Switch) COMMUNICATIONS........................................................................................................298
11. MAINTENANCE AND TECHNICAL SERVICE ............................................................................................................... 300
12. GUARANTEE.............................................................................................................................................................. 300
13. EU DECLARATION OF CONFORMITY.......................................................................................................................... 301
6
CVM-B150-ITF-HF
Instruction Manual

REVISION LOG
Table 1: Revision log.
Date Revision Description
02/18 M210B01-03-18A Initial Version
12/19 M210B01-03-19A Changes in the following sections:
2.- 3.5.- 4.5.- 5.5.- 5.5.4.- 10.1
03/20 M210B01-03-20A Changes in the following sections:
10.1.- 10.2.- 10.3.
06/20 M210B01-03-20B Changes in the following sections:
9.
02/23 M210B01-03-23A Changes in the following sections:
7.4.3.2.
Note: Device images are for illustrative purposes only and may differ from the actual device.
7
Instruction Manual
CVM-B150-ITF-HF

1. VERIFICATION UPON RECEPTION
Check the following points upon receiving the device:
a) The device meets the specifications described in your order.
b) The device has not suffered any damage during transport.
c) Perform an external visual inspection of the device prior to switching it on.
d) Check that it has been delivered with the following:
- An installation guide,
- 4 Retainers used to attach the device,
- 5 plug-in connectors with screws,
- 1 seal,
If any problem is noticed upon reception, immediately contact the transport com-
pany and/or CIRCUTOR's after-sales service.
2. PRODUCT DESCRIPTION
The CVM-B150 device measures,calculates and displays the main electrical parameters in single-phase
networks, with and without neutral two-phase networks, balanced three-phase networks, with ARON
measurement or unbalanced networks. The measurement is taken in RMS, via four AC voltage inputs
and four current inputs.
The current measurement is taken indirectly with transformers/5 or/1.
It is a modular device that can be expanded using expansion modules with different functions.
The device features:
- 3 keys that allow you to browse between the various screens and program the device.
- 3 indicator LEDs: CPU, ALARM and on the navigation keys.
- LCD Display, for displaying all parameters.
- 2 digital inputs, to select the tariff, detect the logic state of external signals or as act as an
impulse input.
- 2 transistor digital outputs, fully programmable.
- 2 relay digital outputs, fully programmable.
- RS-485 communications, with two serial protocols: MODBUS RTU ® and BACnet.
8
CVM-B150-ITF-HF
Instruction Manual

The CVM-B150 can be expanded with the following expansion modules:
 M-CVM-AB-8I-8OTR, expansion module with 8 transistor digital inputs and 8 transistor
digital outputs.
M-CVM-AB-8I-8OR, expansion module with 8 relay digital inputs and 8 relay digital outputs.
M-CVM-AB-4AI-8AO, expansion module with 4 analogue inputs and 8 analogue out puts.
M-CVM-AB-Modbus/TCP(Bridge), expansion module for connecting the device to a Mod-
bus/TCP network and as an Ethernet to RS-485 gateway.
M-CVM-AB-LON, expansion module for connecting the device to a LonWorks network.
M-CVM-AB-Profibus, expansion module for connecting the device to a Profibus network.
M-CVM-AB-MBus, expansion module for connecting the device to a M-Bus network.
M-CVM-B-Datalogger, expansion module that can be used to store data in the embedded
PowerStudio platform integrated in the module.
M-CVM-AB-Modbus/TCP(Switch), expansion module for connecting the device to a Mod-
bus/TCP network and as an Ethernet to Ethernet gateway.
9
Instruction Manual
CVM-B150-ITF-HF

3. DEVICE INSTALLATION
3.1.- PRIOR RECOMMENDATIONS
In order to use the device safely, it is critical that individuals who handle it follow the
safety measures set out in the standards of the country where it is being used, use the
necessary personal protective equipment, and pay attention to the various warnings
indicated in this instruction manual.
The CVM-B150 device must be installed by authorised and qualified staff.
The power supply plug must be disconnected and measuring systems switched off before handling, al-
tering the connections or replacing the device. It is dangerous to handle the device while it is powered.
Also, it is critical to keep the cables in perfect condition in order to avoid accidents, personal injury and
damage to installations.
The manufacturer of the device is not responsible for any damage resulting from failure by the user
or installer to observe the warnings and/or recommendations set out in this manual, nor for damage
resulting from the use of non-original products or accessories or those made by other manufacturers.
If an anomaly or malfunction is detected in the device, do not use it to take any measurements.
Inspect the work area before taking any measurements. Do not take measurements in dangerous ar-
eas or where there is a risk of explosion.
Disconnect the device from the power supply (device and measuring system power
supply) before maintaining, repairing or handling the device's connections.
Please contact the after-sales service if you suspect that there is an operational fault
in the device.
3.2.- INSTALLATION
The device is installed on a panel. All connections are located inside the electric panel.
Table 2: Panel drill holes for installation.
Model Panel drill hole (according to DIN 43700)
CVM-B150 138+0.8 x 138+0.8 mm
Terminals, opening covers or removing elements can expose parts that are hazardous
to the touch while the device is powered. Do not use the device until it is fully installed.
The device must be connected to a power circuit that is protected with gL fuses (IEC 269) or M fuses,
with a rating of 1 to 2 A. It must be fitted with a circuit breaker or equivalent device for disconnecting
the device from the power supply mains.
The power and voltage measuring circuit must be connected with cables that have a minimum
10
CVM-B150-ITF-HF
Instruction Manual

cross-section of 1mm2 and the wires must to endure a temperature at least 77 degrees.
The secondary line of the current transformer will have a minimum cross-section of 2.5 mm2.
Current needs to be measured via external current transformers providing reinforced insulation.
3.3.- DEVICE TERMINALS
The CVM-B150 terminals are distributed between the upper and lower face of the device.
3.3.1. TERMINALS ON THE UPPER FACE
Table 3:List of terminals on the upper face of the CVM-B150.
Terminals of the top side of the device
1: VREF, Reference voltage input 10: T1, Digital output of transistor 1
2: NREF, Reference voltage neutral 11: T2, Digital output of transistor 2
3: N, Voltage input neutral 12: TC, Common digital output of transistor
4: VL3,Voltage input L3 13: A(+), RS485
5: VL2, Voltage input L2 14: B(-), RS485
6: VL1, Voltage input L1 15: S, GND for RS-485
7: I1, Digital input 1 16, 17: R1, Relay digital output 1
8: I2, Digital input 2 18, 19: R2, Relay digital output 2
9: Ic, for digital inputs
1234 5 6
7
10
9
12
11 13
14
15
8
16 17 18 19
Figure 1: CVM-B150 terminals, upper face.
11
Instruction Manual
CVM-B150-ITF-HF

3.3.2. TERMINALS ON THE LOWER FACE
Table 4:List of terminals on the lower face of the CVM-B150.
Device terminals
20 : ~ +, Auxiliary power supply. 25: S2, Current input L2
21: ~ -, Auxiliary power supply. 26: S1 , Current input L3
22: S1 , Current input L1 27: S2, Current input L3
23: S2, Current input L1 28: S1, Neutral current input, LN
24: S1 , Current input L2 29: S2, Neutral current input, LN
20 21
22 23 24 25 26 27 28 29
Figure 2:CVM-B150 terminals, lower face.
12
CVM-B150-ITF-HF
Instruction Manual

3.4.- CONNECTION DIAGRAMS
3.4.1. THREEPHASE NETWORK MEASUREMENT WITH A 4WIRE CONNECTION.
Measurement system:
Secondary winding of the current transformer:
Secondary winding of the neutral current transformer:
Power
Supply
VL1
L1
L2
L3
N V L3 L2 V L1 V
VL1 VL2 VL3
ab
A B
ab
AB
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
P1 P2 P1 P2
S1 S2
LN
P1 P2
NV REF REF
N
S1 S2
P1 P2
POWER SUPPLY
VL2 VL3 NVREF
NREF
ab
AB
VREF
NREF
S1 S2
P1 P2 S1 S2
P1 P2 S1 S2
P1 P2
LOAD
Figure 3: Three-phase measuring with a 4-wire connection (transformer secondary:/1A,/5A).
Note: The device can calculate the neutral current without having to measure it, option: Calculated
current .
13
Instruction Manual
CVM-B150-ITF-HF

3.4.2. THREEPHASE NETWORK MEASUREMENT WITH A 3WIRE CONNECTION.
Measurement system:
Secondary winding of the current transformer:
Power
Supply
VL1 VL2 VL3
L1
L2
L3
N V L3 L2 V L1 V
VL1 VL2 VL3
ab
A B
ab
A B
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
P1 P2 P1 P2
S1 S2
LN
P1 P2
NV REF REF
S1 S2
P1 P2 S1 S2
P1 P2 S1 S2
P1 P2
POWER SUPPLY
LOAD
Figure 4: Three-phase measuring with a 3-wire connection (transformer secondary:/1A,/5A).
14
CVM-B150-ITF-HF
Instruction Manual

3.4.3.- THREEPHASE NETWORK MEASUREMENT WITH A 3WIRE CONNECTION AND 3 VOLTAGE
TRANSFORMERS
Measurement system:
Secondary winding of the current transformer:
VL1 VL2 VL3
L1
L2
L3
N V L3 L2 V L1 V
VL1 VL2 VL3
ab
A
ab
A B
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
P1 P2 P1 P2
S1 S2
LN
P1 P2
NV REF REF
S1 S2
P1 P2 S1 S2
P1 P2 S1 S2
P1 P2
POWER SUPPLY
ab
AB
B
LOAD
Power
Supply
Figure 5: Three-phase measuring with a 3-wire connection and 3 voltage transformers (transformer secondary:/1A,/5A).
15
Instruction Manual
CVM-B150-ITF-HF

3.4.4. THREEPHASE NETWORK MEASUREMENT WITH A 3WIRE CONNECTION AND TRANSFORM
ERS WITH AN ARON CONNECTION.
Measurement system:
Secondary winding of the current transformer:
Power
Supply
VL1 VL2 VL3
L1
L2
L3
N V L3 L2 V L1 V
VL1 VL2 VL3
ab
A B
ab
A B
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
P1 P2P1 P2
S1 S2
LN
P1 P2
NV REF REF
S1 S2
P1 P2
S1 S2
P1 P2
POWER SUPPLY
LOAD
Figure 6: Three-phase measuring with a 3-wire connection and transformers in an ARON connection (transformer secondary:/1A,
/5A).
16
CVM-B150-ITF-HF
Instruction Manual

3.4.5. TWOPHASE NETWORK MEASUREMENT WITH A 3WIRE CONNECTION.
Measurement system:
Secondary winding of the current transformer:
Secondary winding of the neutral current transformer:
Power
Supply
VL1
L1
L2
N V L3 L2 V L1 V
VL1 VL2
ab
A B
ab
AB
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
P1 P2 P1 P2
S1 S2
LN
P1 P2
NV REF REF
N
S1 S2
P1 P2
POWER SUPPLY
VL2 NVREF
NREF
ab
AB
VREF
NREF
S1 S2
P1 P2 S1 S2
P1 P2
N
LOAD
Figure 7: Two-phase measuring with a 3-wire connection (transformer secondary:/1A,/5A ).
Note: The device can calculate the neutral current without having to measure it, option: Calculated
current .
17
Instruction Manual
CVM-B150-ITF-HF

3.4.6. SINGLEPHASE NETWORK MEASUREMENT, PHASE TO PHASE, WITH A 2WIRE CONNECTION.
Measurement system:
Secondary winding of the current transformer:
Power
Supply
L1
L2
N V L3 L2 V L1 V
VL1
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
P1 P2 P1 P2
S1 S2
LN
P1 P2
NV REF REF
S1 S2
P1 P2
POWER SUPPLY
VL2
LOAD
Figure 8: Phase to phase single-phase measuring with a 2-wire connection (transformer secondary:/1A,/5A).
18
CVM-B150-ITF-HF
Instruction Manual

3.4.7.- SINGLEPHASE NETWORK MEASUREMENT, PHASE TO NEUTRAL, WITH A 2WIRE CONNEC
TION.
Measurement system:
Secondary winding of the current transformer:
Power
Supply
VL1
L1
N V L3 L2 V L1 V
VL1
ab
AB
S1 S2 S1 S2 S1 S2
L1
P1 P2
L2 L3
P1 P2 P1 P2
S1 S2
LN
P1 P2
NV REF REF
N
POWER SUPPLY
NVREF
NREF
ab
AB
VREF
NREF
S1 S2
P1 P2
N
LOAD
Figure 9: Phase to neutral single-phase measuring with a 2-wire connection (transformer secondary:/1A,/5A).
19
Instruction Manual
CVM-B150-ITF-HF

3.5.- STARTING UP THE DEVICE
When the CVM-B150 has been powered up, the display will show the following screen , Figure 10, while
the device’s software is loading.
Figure 10:Loading screen.
If there has been an error in the start-up process, the device displays an error message. The possible
error messages are shown in Table 5.
Table 5:Error messages detected when starting up the device.
Error Description/Action
SD ERROR
Indicates that the microSD is not inserted or has not been detected.
Action
Disconnect the device’s power supply and check if the microSD is correctly inserted.
FILE NOT FOUND
Indicates that the graphic resource files were not found.
Action
Disconnect the device’s power supply and check if the graphic resource files have been
copied onto the microSD: resources_CVM_B1xx.pbr and resources_CVM_B1xx_cp.pbr
(see : “8.- SOFTWARE UPDATE” ).
If the files are there and the error persists, format the microSD and update the device by
following the steps indicated in section “8.- SOFTWARE UPDATE”.
FILE LOAD FAILED
Indicates that the graphic resource files are corrupted.
Action
Disconnect the device’s power supply, format the microSD and update the unit by follow-
ing the steps indicated in section “8.- SOFTWARE UPDATE”
Note: These errors only affect graphic resources, the device is still working correctly and you can access
your data via communications.
20
CVM-B150-ITF-HF
Instruction Manual