Cisco BWX360 WiMAX User manual

Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Cover_front.fm / 07.04.2010
Template 2006_02_28
Cisco BWX360 WiMAX Outdoor Modem
Installation Guide
This device works in a frequency band for which a general licence might have to be obtained.
Please contact your service provider or your National Authority for Frequency Management about
licensing before putting this device into service.

1
Contents
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / SE680WiMAXIVZ.fm / 07.04.2010
Schablone 2006_02_28
Contents
For your safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Notes on assembly instructions . . . . . . . . . . . . . . . . . . . . . . 3
The Cisco BWX360 WiMAX Outdoor Modem . . . . . . . . . . . . 4
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the Cisco BWX360 WiMAX Outdoor Modem . . . . 8
Choosing locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting up the antenna mast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Protecting the mast against lightning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Assembling the outdoor modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connecting the indoor unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Preparing to use the Cisco BWX360 WiMAX Outdoor Modem . . . . . . . . . . . . . . . 17
Launching the user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connecting to the WiMAX network and the Internet . . . . . . . . . . . . . . . . . . . . . . . . 19
Precisely aligning the antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Finishing off the assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Federal Communications Commission (FCC) Statements . . . . . . . . . . . . . . . . . . . 26
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

2
For your safety
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Safety.fm / 07.04.2010
Template 2006_02_28
For your safety
Please read the safety instructions carefully before assembly and before putting into
service.
Safety precautions
General safety instructions
◆Only pass on the Cisco BWX360 WiMAX Outdoor Modem to third parties with this
user guide and the assembly instructions.
◆TheCisco BWX360WiMAXOutdoorModemmustonlybeinstalledandputintouse
by a qualified electrician in accordance with the supplied installation instructions.
◆National laws and regulations must be considered before putting the device into
service.
◆These devices are professional IT equipment. Keep the devices beyond the reach
of children.
Safety instructions for connection
◆Only use undamaged original accessories.
◆The outdoor modem must only be installed by a qualified electrician in accordance
with the assembly instructions.
Safety precautions for the Cisco BWX360 WiMAX Outdoor Modem
◆The operation of medical appliances may be affected. Be aware of the technical
conditions in your particular environment, e.g. doctor's surgery.
◆The Cisco BWX360 WiMAX Outdoor Modem can interfere with the functioning of
medical devices such as pacemakers. Keep at least 20 cm between the devices
and the pacemaker. For more information consult your doctor.
◆Do not operate the indoor unit under the influence of direct heat sources (e.g.
directly in the sun).
◆The Cisco BWX360 WiMAX Outdoor Modem complies with the regulations on lim-
iting the effect of electromagnetic fields on the general population.
◆Do notuse the devices in environments witha potential explosion hazard, e.g. auto
paint shops or in a humid environment (bathroom etc.).
◆Only clean the Cisco BWX360 WiMAX Outdoor Modem with a soft anti-static cloth.

3
Notes on assembly instructions
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Safety.fm / 07.04.2010
Template 2006_02_28
Notes on assembly instructions
These assembly instructions describe the assembly and operation of the individual
components of the Cisco BWX360 WiMAX Outdoor Modem. The configuration of the
fully installed system is discussed in the user guide that you received with the
Cisco BWX360 WiMAX Outdoor Modem.
◆Please readtheassembly instructionscarefully beforeusingthedevicesforthefirst
time.

4
The Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Product_intro.fm / 07.04.2010
Template 2006_02_28
The Cisco BWX360 WiMAX Outdoor Modem
Scope of delivery
◆1 outdoor modem with integrated antennas
◆Assembly equipment:
– Distance piece for elevation setting
– Mast bracket with fastening clamps, fastening screws and brackets
◆Assembly accessories:
– 1 RJ45 plug (Phoenix connector VS-08-RJ45-5-Q/IP67 BK) to connect the
Ethernet cable to the outdoor modem
◆1 indoor unit
– 1 Ethernet cable for the internal connection to the PC, 1.8 m
– 1 power supply unit
◆1 assembly instructions
◆1 user guide
Tools and equipment required
You will require the following tools and equipment for assembly:
◆Antenna mast with assembly equipment (for mounting on a mast); the antenna
mast must have a diameter of 2–3 inches (50.8 mm–76.2 mm) and be designed for
assembling this kind of antenna.
◆Sealing material for the wall, window or roof duct
◆Ethernet cable (non-assembled) for the Ethernet connection to the indoor unit. For
the connection of the outdoor modem to the indoor unit only use a round Ethernet
cable (Ø 6.0-8.5 mm), which is approved for the outdoor use. We recommend to
contact one of the manufacturers which are mentioned in the chapter "Ethernet
cable" on page 24.
◆RJ45 plug (Phoenix) for the connections required indoors. Also a standard CAT5e
Ethernet cable for connecting indoor units to the PC or router.
◆LSA+ wall connection socket, feeder tool and standard CAT5e Ethernet cable, if
you wish to connect the Ethernet cable from outside to a wall connection socket.
◆Cable clamps and cable ties for attaching the Ethernet cable to the antenna mast,
the wall bracket and other outdoor and indoor areas
◆Ground cable for earthing (grounding) the metal casing of the outdoor modem
(wire: stranded, green, #6 AWG, ROHS; lug: CONN, one-hole #6, ROHS)
Depending on the installation conditionsand customer requirements, you
can also connect the Ethernet cable from the IN connector of the indoor
unitto a standard LAN socket, andRJ45 plug (e.g. Phoenix connector VS-
08-RJ45-5-Q/IP20 BK, see "Sources" on page 24) or a patch panel.

5
The Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Product_intro.fm / 07.04.2010
Template 2006_02_28
Product overview
The Cisco BWX360 WiMAX Outdoor Modem is the WiMAX solution that provides pri-
vate and business users with cost-effective last mile broadband wireless access. The
Cisco BWX360 WiMAX Outdoor Modem employs non-line-of-sight OFDM technology
according to the IEEE 802.16e standard. It provides astandard-based means for offer-
ing new forms of voice, video and data services. With the Cisco BWX360 WiMAX Out-
door Modem , you can enjoy high-speed Internet access, Voice-over-IP telephony
(VoIP), video streaming and a range of other services.
The Cisco BWX360 WiMAX Outdoor Modem works in the 2.6 and 3.5 GHz frequency
range respectively. Due to its architecture, interfaces and simple network integration,
the Cisco BWX360 WiMAX Outdoor Modem is designed to deliver high-speed Internet
access, including data streaming services. This solution represents a cost-effective,
wireless alternative to wired xDSL systems. It provides you with high performance
broadband services – with low costs for coverage and high spectral efficiency for
capacity – and advanced radio resource management.
The outdoor modem holds the integrated antennas and is intended for mounting on a
wall or a mast. The power is supplied via the Ethernet port (Power over Ethernet, PoE).
The indoor unit is only designed for indoor use and supplies the power to the outdoor
modem. It is also the connection point for the terminal (e.g. PC or router).

6
The Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Product_intro.fm / 07.04.2010
Template 2006_02_28
Connectors and LEDs
Outdoor modem
Ethernet socket
Outdoor antennas (integrated)

7
The Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Product_intro.fm / 07.04.2010
Template 2006_02_28
Indoor unit
You can check the status of the startup procedure on the LEDs, see
"Preparing to use the Cisco BWX360 WiMAX Outdoor Modem" on page 17.
1Connector for the power supply unit, see "Preparing the power
supply" on page 17.
2 CONNECT The LED shows whether or not the indoor unit is properly con-
nected to the outdoor modem.
◆Green: The indoor unit is properlyconnected to theoutdoor
modem.
3 FAULT The LED shows whether or not the indoor unit is properly con-
nected to the outdoor modem.
◆Red: The connection between the indoor unit and the out-
door modem is faulty.
4ON The LED shows that power is being supplied.
◆Green: The Cisco BWX360 WiMAX Outdoor Modem is
powered correctly.
5IN Ethernet socket for data exchange with a PC or network (RJ45,
10/100 Base T), see "Connecting the PCor laptop" on page 16.
6OUT Ethernet socket for connection with the outdoor modem (RJ45,
power supply and data transmission), see "Connecting the
indoor unit" on page 15.
7Clips for wall mounting
12
3
4
5
6
7

8
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
Installing the Cisco BWX360 WiMAX Outdoor
Modem
For installing the Cisco BWX360 WiMAX Outdoor Modem you have to perform the fol-
lowing steps:
1. Choosing locations (see page 9)
2. Setting up the antenna mast (see page 10).
3. Protecting the mast against lightning (see page 10)
4. Assembling the outdoor modem (see page 12)
5. Connecting the indoor unit (see page 15)
When the installation is completed you have to perform the following steps in order to
put your Cisco BWX360 WiMAX Outdoor Modem into operation:
1. Preparing to use the Cisco BWX360 WiMAX Outdoor Modem (see page 17)
2. Launching the user interface (see page 18)
3. Connecting to the WiMAX network and the Internet (see page 19)
4. Precisely aligning the antenna (see page 21)
5. Finishing off the assembly (see page 22)
The Cisco BWX360 WiMAX Outdoor Modem must beassembled and put
into service by a qualified electrician.
³Only commence the outdoor work once you have taken all the neces-
sary steps to make the location safe.
Be sure to observe the safety precautions.

9
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
Choosing locations
When choosing locations, please note the following:
1. First choose the location for the indoor unit:
– When choosing the location, note the specified temperature range of the indoor
unit (see "Specifications" on page 23).
– The indoor unit is only suitable for indoor use.
– The indoor unit can be operated either on a horizontal surface or mounted on a
wall. Always make sure the connections cannot become loose once the system
has been put into service and check that the LEDs are clearly visible.
–Power supply:
Power is supplied to the Cisco BWX360 WiMAX Outdoor Modem via the indoor
unit. Therefore, the location must be close to a suitable mains connection (cable
length of the supplied power supply unit).
–Wall duct:
To connectto the outdoor modem, the corresponding Ethernet cable mustbe fed
through the wall to the outside of the building. It must be possible to make a suit-
able wall duct at or close to the indoor unit.
Please note that the maximum permitted cable length is 50 m.
–PC or network:
Establishing a connection between the indoor unit and a PC or network-switch
should ideally be possible from the location via the Ethernet cable. If the PC is
moved from its original place, the indoor unit should still be able to be reached
simply by using standard cable lengths.
2. Please note the following when setting up the antenna mast/modem:
– There should not be any obstructions (walls, trees etc.) in front of the antenna.
The best results will be obtained if the outdoor modem is in sight of the WiMAX
base station. If necessary, you can also reflect the radio waves off neighbouring
buildings.
– The antenna mast must be structurally secure. Check how secure the various
attachments are.
– The antenna mast must be within reach of the cable. Ideally, the Ethernet cable
should be protected outside (from frost, sun, unauthorised and mechanical influ-
ences etc.).
– The antenna mast should be positioned near a lightning conductor. A suitable
lightning conductor must be installed where necessary.

10
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
Setting up the antenna mast
Information on how to install the antenna mast is not included in these installation
instructions. Please observe all the safety provisions and other notes contained in the
assembly instructions for the antenna mast. In particular, make sure the antenna mast
hassufficient load capacity. Ifyou areinstalling the maston theroof, makesure theroof
is fully sealed again afterwards.
If necessary, you can attach the mast brackets to the mast when you install it.
Protecting the mast against lightning
Preparation
◆The outdoor modem is not designed to withstand being struck directly by lightning
and must be protected accordingly. The antenna must therefore be installed in
areas that are protected against lightning (Lightning Protection Zone 0B). The cor-
responding separation distance (IEC 62305) must be complied with.
Earthing (grounding) and lightning protection work may only be carried out by elec-
tricians specifically qualified for such work.
◆The appropriate earthing (grounding) clamps must be used to create an equipoten-
tial bonding between a cable shield and an equipotential bonding bar that complies
with regulations (for sources see "Earthing (gounding) clamps" on page 25).

11
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
Connecting the earthing (grounding) cable to the outdoor modem
Make sure you ground the metal casing of the outdoor modem according to the instruc-
tions.
1. Undo or remove the M5 earthing (grounding) screw on the modem casing.
2. Attach the cable lug at the end of the earthing (grounding) cable.
Make sure when you do this that the cable lug cannot come loose. You can ensure
this, for example, by crimping it twice (once on the flex and again on the insulation)
or by applying an appropriately designed shrink tubing which covers the cable lug
and the insulation.
3. Attach the cable lug to the casing with the M5 earthing (grounding) screw.
Make sure that the screwed connection cannot come loose. To ensure this, use a
toothed contact disc (not supplied), which you fit between the cable lug and the
earthing (grounding) screw.
The cable lug is not provided. Only use tin-plated cable lugs with eyelet
(available from your retailer).
DO NOT screw the earthing (grounding) cable directly to the metal casing
of the device, as this could lead to corrosion between the cable and the
casing.

12
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
Assembling the outdoor modem
You basically have three options for installing the outdoor modem:
◆Vertically on a mast (see below), or
◆Tilted up or down on a mast with an angled bracket (see "Angled installation on a
mast" on page 13). Choose the type of installation that allows the best alignment of
modem to base station on your building.
◆Directly attached to a wall
Vertical installation on a mast
1. Take the four bolts with the welded-on
nuts and screw them into the housing
with the shorter end of the bolts, so that
the nuts are resting on the housing.
2. Attachthehousingtothemastusingthe
clamps and secure the clamps with the
nuts.

13
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
Angled installation on a mast
Installing the modem using the supplied bracket allows two possible directions of incli-
nation (up or down) and four different tilt angles each, dependingon how you attach the
bracket to the housing.
1. Fasten the bracket to the housing with the nuts welded onto the bolts:
– To have the modem facing up, fasten the bracket to thebottom edge of the hous-
ing; to have the modem facing down, fasten the bracket to the top edge of the
housing.
– Choose your preferred tilt angle: You get the largest tilt if you fit the bracket with
the smaller notch facing inward, and you get the smallest tilt if you fit it with the
larger notch facing outward.
2. Attach the housing to the mast using the
clamps and secure it with the nuts.

14
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
Preparing to connect to the indoor unit
To connect the indoor unit to the outdoor modem you perform the following steps:
1. Making a wall duct.
2. Provisionally laying the Ethernet cable.
3. Checking connection options in the house.
4. Connecting an Ethernet cable to the outdoor modem.
Making a wall duct
1. Note how close you are to the indoor unit.
2. Check what types of wall ducts are suitable (wall or window duct) and make one.
Provisionally laying the Ethernet cable
The cable must satisfy the following conditions:
◆For connecting the outdoor modem to the indoor unit, only use a round Ethernet
cable which is approved for outdoor use.
◆The outer diameter of the cable must correspond to the clamping area of the con-
nector plug. This permitted diameter range is 5 mm to 8.5 mm.
◆The cable must satisfy the requirements for cables used outdoors at the relevant
installation location.
The following influencing factors in particular must be taken into account:
– Ambient temperature
– Rain, water vapour or accumulation of water
– Presence of corrosive, contaminative or other chemical substances
– Mechanical stresses (e.g. compression stress, tensile loading, torsional load,
bending stress, alternating stress etc.)
– Animals (e.g. damage caused by rodents or insects)
– Plants (e.g. mildew)
– Radiation (e.g. UV radiation)
◆The maximum permitted cable length is 50 m.
◆To comply with regulations, it may be necessary to ground the cable shield.
◆To protect the connected IT installation from power surges, you may need to use a
surge protection box (see "Surge protection box" on page 24).
Proceede as follows:
1. Feed the non-assembled cable through the wall duct from inside to outside.
2. Lay the cable along the rough path it should take and, if possible, provisionally po-
sition fixings.
Local building codes must be followed when constructing a wall duct or
whatever method of wall penetration is used to pass the ethernet cable
into the building.

15
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
Checking connection options in the house
Choose one of the following options for connecting the Ethernet cable in the house:
1. Fix the wall connection socket (LSA+ technology) in place and connect the cable
from outside to it. For this you will require a corresponding connection socket and
possibly a feeder tool for the LSA+ terminal. Feed an Ethernet cable with RJ45
plugs from the wall connection socket to the indoor unit (standard CAT5e, available
from your retailer in various lengths).
2. Connect the cable from outside directly to the indoor unit. For indoor use, you need
anRJ45plug,see"Sources"onpage 24.FeedanEthernetcablewithanRJ45plug
from the indoor unit to a PC or router (standard CAT5e, available from your retailer
in various lengths).
Connecting an Ethernet cable to the outdoor modem
1. Slip the support sleeve over the unassembled cable to be screwed in later.
2. Attach a Phoenix connector to the end of the Ethernet cable that is outside. Please
read the instructions that come with the plug.
3. Insert the RJ45 plug of the assembled cableinto the Ethernet socket of the outdoor
modem.
4. Slide the sleeve over the connected RJ45 plug and screw this into the Ethernet
socket. Make sure the connection is water-tight.
5. Use cable clamps to attach the cable to the mast. Please note that the cable must
be long enough to turn the antenna at a later stage.
6. Lay and attach the cable from the antenna mast along a path on which its function-
ality is not affected by external influences.
Connecting the indoor unit
Wall mounting (optional)
The indoor unit is fittedwith two clips for wall mounting. Wallmounting is notabsolutely
necessary, but is recommended to make the cable connections mechanically secure.
◆Use screw fittings, anchor fittings and cable clamps to mount the indoor unit on a
wall.
◆Make sure the LEDs are easily visible.

16
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
Establishing the cable connections
Connecting the outdoor modem
1. Shorten the cable to the length required for connecting it to the indoor unit:
– If there is any surplus cable, pull this inside through the wall duct.
– Lay the inside section of the cable up to the location of the indoor unit or the wall
connection socket and attach the cable professionally.
– Fit an Ethernet plug to the cable end.
First shorten the cable to a length that allows the indoor unit or the wall connec-
tion socket to be easily reached.
2. Connect the RJ45 plug of the Ethernet cable from the outdoor modem to the OUT
connector of the indoor unit.
Or
1. Connect the RJ45 plug of the Ethernet cable of the outdoor modemto the wall con-
nection socket.
2. Connect the wall connection socket and the indoor unit using an Ethernet cable
(CAT5e).
Connecting the PC or laptop
1. Connect the supplied, pre-assembled Ethernet cable to the IN connector on the in-
door unit.
2. Then connecttheEthernetcableto theEthernetsocketon thePCorlaptopthatyou
are using for putting the system into service for the first time.
The PC or laptop with the special settings can be on and ready for use, but this is
not obligatory.
The indoor unit should not be considered as an Ethernet terminal. The full
length of the Ethernet cable from the outdoor modem to the Ethernet ter-
minal (e.g. a router or a PC) must not exceed 100 m. The maximum per-
mitted cable length between indoor unit and outdoor modem is 50 m. If
you utilise this completely the cable length between Ethernet terminal and
indoor unit must also not exceed 50 m.
When the Cisco BWX360 WiMAX Outdoor Modem has been assembled
and is put into service, itis connected to thePC or the customer'snetwork
via the IN connector of the indoor unit.
Whenyou first put the system into service, itis recommended that you first
connect a laptop that has the appropriate settings for this purpose. For
information on what settings to make on the laptop, please read the sup-
plied user guide.

17
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
Preparing the power supply
1. Check that all of the assembly steps and connections up to this point have been
made correctly and in full.
2. Connect the supplied power supply unit to the POWER connector of the indoor unit.
3. Begin putting the system into service.
As soon as you have connected the indoor unit to the mains power supply, the sys-
tem is started up.
Preparing to use the Cisco BWX360 WiMAX Outdoor Modem
1. Start up the connected PC or laptop and make any necessary settings. You will find
the preconditions for the PC in the user guide for the Cisco BWX360 WiMAX Out-
door Modem.
2. If you are sure you have connected everything up correctly, connect the indoor unit
to a power socket that is ready for use via the power supply unit.
The system starts up and performs a self-test.
After the self-test, theCisco BWX360 WiMAX Outdoor Modem continually attempts
to register with a base station. Registration with the base station may be successful
immediately. If not, registration will take place when the Cisco BWX360 WiMAX
Outdoor Modem is being configured (see "Connecting to the WiMAX network and
the Internet" on page 19)
Only use the Cisco BWX360 WiMAX Outdoor Modem with the supplied
power supply unit.
Part number: C39280-Z4-C584
Input: 100-240 V, 0.95 A AC
Output: 56 V, 0.55 A DC
The connection technology between the outdoor modem and the
indoor unit complies with the "PoE" standard. This means the DC
power is supplied via the Ethernet cable
(Pins 4/5 = Power +, Pins 7/8 = Power -)
The DC voltage supplied to the indoor unit is 56 V with a maximum
deviation of 4%.
As part of the standard, a self-test is performed to check the voltage
between the connected devices is correct. The indoor unit only
releases its supply voltage once the outdoor modem and the indoor
unit have accepted the correct voltage.
³If the activation is not successful, check whether the connections
have been correctly assembled.

18
Installing the Cisco BWX360 WiMAX Outdoor Modem
Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010
Template 2006_02_28
3. Duringthe startup procedure, check the LED displayon the indoor unit (see "Indoor
unit" on page 7). The following signify a successful system start:
–TheON power supply LED lights up green, and the Cisco BWX360 WiMAX Out-
door Modem starts a self-test.
–TheFAULT LED(red)andtheCONNECT LED(green)lightupforapproximately
1 second and then go out.
– If the connection to the outdoor modem is then found to be free from errors, the
CONNECT LED is continuously lit up green.
If an error occurs, the FAULT and CONNECT LEDs start to flash alternately at
regular intervals.
Launching the user interface
1. Open your Web browser.
2. Enter the IP address of the Cisco BWX360 WiMAX Outdoor Modem in the
browser's address field:
http://192.168.2.1
3. Press Enter (Return).
Login
If a system password has been set up on the Cisco BWX360 WiMAX Outdoor Modem,
the login screen will now open.
1. Enter the system password supplied by your provider in the text box and clickOk.
The start page of the user interface opens, in which you can change the language
if necessary.
If no system password has been set up on your Cisco BWX360 WiMAX Outdoor
Modem, a securitywarning will appear first. You should then assign a system pass-
word as soon as possible.
2. Confirm the security warning with Ok.
The user interface start page opens.
If the login screen does not open:
³Checkthe connections and the PC configuration. For details,refer to the user guide
for the Cisco BWX360 WiMAX Outdoor Modem.
³If you use a firewall it must allow connectionto the Cisco BWX360WiMAX Outdoor
Modem. For details, referto theuser guidefor yourfirewall.If necessary, deactivate
the firewall while you configure the Cisco BWX360 WiMAX Outdoor Modem.