Cisco ASR 9001 Manual

Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation
Guide
First Published: 2013-08-25
Last Modified: 2016-10-04
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version
of the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://
www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
©2016 Cisco Systems, Inc. All rights reserved.

CONTENTS
Preface Preface ix
Changes to This Document ix
Audience x
Purpose x
Document Organization x
Documentation Conventions xi
Obtaining Documentation and Submitting a Service Request xii
CHAPTER 1 Preparing for Installation 1
Safety Guidelines 2
General Safety Guidelines 3
Compliance and Safety Information 3
Laser Safety 3
Energy Hazard 4
Preventing Electrostatic Discharge Damage 4
Lifting Guidelines 5
Site Requirement Guidelines 5
Site Layout and Equipment Dimensions 5
Site Wiring Guidelines 7
Chassis Air Flow Guidelines 8
Rack-Mounting and Air Flow Clearance Guidelines 9
Telco 2-Post Rack 10
Open 4-Post Rack 11
Enclosed Rack with Perforated Sides 12
Air Flow Guidelines for Enclosed Rack Installation 12
Temperature and Humidity Guidelines 13
Power Connection Guidelines 13
Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide
iii

AC Powered Routers 14
AC Power Cord Illustrations 16
DC Powered Router 19
NEBS Supplemental Unit Bonding and Grounding Guidelines 22
Cisco ASR 9001 Router Port Connection Guidelines 23
Console Port and Auxiliary Port Connection Guidelines 25
Console Port Signals 26
Auxiliary Port Signals 26
Management LAN Ports Connection Guidelines 27
Management LAN Port LED Indicators 28
Management LAN RJ-45 Cabling 28
Sync Ports Connection Guidelines 29
SYNC Port LED Indicators 30
RP External USB Port 31
CHAPTER 2 Unpacking and Installing the Chassis 33
Pre-Installation Considerations and Requirements 33
Unpacking the Cisco ASR 9001 Router 34
Positioning the Router 36
Installing the Cisco ASR 9001 Chassis 36
Before you Begin 36
Rack-Mounting the Chassis 36
Verifying Rack Dimensions 37
Installing the Chassis in a Two-Post Rack 37
Installing the Chassis in a Four-Post Rack 39
Supplemental Bonding and Grounding Connections 42
Installing the Optional Air Plenum Kit 43
Air Plenum Kit Contents 43
Supported Rack Types and Adapter Plates 44
Installing the Air Plenum Kit 44
Installing the Air Plenum Kit in a 19-inch Rack 45
Installing the Air Plenum Kit in an ETSI Two-Post to Four-Post Rack 51
CHAPTER 3 Installing Modules and Cables in the Chassis 57
Fixed 4x10-Gigabit Ethernet Ports 57
Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide
iv
Contents

Modular Port Adapters 58
20-Port Gigabit Ethernet Modular Port Adapter 59
4-Port 10 Gigabit Ethernet Modular Port Adapter 60
2-Port 10 Gigabit Ethernet Modular Port Adapter 61
2-Port 40 Gigabit Ethernet Modular Port Adapter 63
1-Port 40 Gigabit Ethernet Modular Port Adapter 65
Installing and Removing Modular Port Adapters 67
Handling Modular Port Adapters (MPAs) 67
Online Insertion and Removal 68
Modular Port Adapter (MPA) Installation and Removal 69
Optical Device Installation and Removal 69
Cleaning Optical Devices 70
Checking the Installation 70
Verifying the Installation 70
Using show Commands to Verify Modular Port Adapter (MPA) Status 71
Using show Commands to Display Modular Port Adapter (MPA) Information 71
Using the ping Command to Verify Network Connectivity 72
Installing and Removing SFP and XFP Modules 73
Cable Management 73
Cable Management Tray 73
Installing a Cable Management Tray 74
Removing a Cable-Management Tray 74
Cable Management Bracket 75
Installing a Cable Management Bracket 76
Removing a Cable-Management Bracket 76
Connecting Route Processor Cables 77
Connecting to the RP Console Port 79
Connecting to the RP Auxiliary Port 79
Connecting to the RP Ethernet Management Ports 80
Connecting Power to the Router 80
Connecting Power to an AC-Powered Router 80
Connecting Power to a DC-Powered Router 82
Powering on the Router 83
CHAPTER 4 Troubleshooting the Installation 85
Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide
v
Contents

Troubleshooting Overview 85
Troubleshooting Using a Subsystem Approach 86
Normal Router Startup Sequence 86
Identifying Startup Issues 86
Troubleshooting the Power Subsystem 87
Troubleshooting the AC-Input Power Subsystem 87
Troubleshooting the DC-Input Power Subsystem 89
Troubleshooting a DC Power Module 89
Additional Power Subsystem Troubleshooting Information 90
Hardware and Software Identification 90
Obtaining Temperature and Environmental Information 90
Troubleshooting the Power Distribution System 94
Troubleshooting the Route Processor Subsystem 95
Route Processor Overview 95
RP Front Panel Indicators 96
Ethernet Ports and Status LEDs 98
Auxiliary and Console Ports 98
Monitoring Critical, Major, and Minor Alarm Status 98
Troubleshooting the Line Card 99
Initial Boot Process 99
Status LEDs 99
Configuring and Troubleshooting Line Card Interfaces 100
Configuration Parameters 100
Line Card Interface Address 101
Using Configuration Commands 101
Basic Line Card Configuration 101
Verifying the Transceiver Modules 103
Advanced Line Card Troubleshooting 104
Troubleshooting the Cooling Subsystem 104
Fan Tray Operation 105
Power Module Fans 105
Over-temperature Conditions 105
Isolating Cooling Subsystem Problems 106
CHAPTER 5 Replacing Cisco ASR 9001 Router Components 109
Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide
vi
Contents

Prerequisites and Preparation 109
Field Replaceable Units 109
Online Insertion and Removal 110
Powering Off the Router 110
Removing and Replacing the Fan Tray 111
Removing and Replacing a Fan Tray 112
Removing and Replacing the Air Filter 113
Removing and Replacing AC or DC Power System Components 115
Power Module Replacement Guidelines 115
Removing and Replacing an AC or DC Power Module 115
Removing an AC or DC Power Module 115
Installing an AC or DC Power Module 116
Removing a Chassis from the Equipment Rack 116
Installing a Replacement Chassis in the Equipment Rack 117
Packing a Chassis for Shipment 117
APPENDIX A Technical Specifications 119
Physical Specifications 120
Environmental Specifications 120
AC Electrical Specifications 121
DC Electrical Specifications 122
AC Input Voltage Range 122
DC Input Voltage Range 123
Power System DC Output Levels 123
RP Port Specifications 123
Power Consumption Specifications 124
Fast Ethernet and Gigabit Ethernet SFP Modules 125
10-Gigabit Ethernet SFP+ Transceiver Modules 126
SFP+ Transceiver Modules 131
DWDM SFP+ Transceiver Modules 133
DWDM XFP Transceiver Modules 133
CWDM SFP Transceiver Modules 136
10GBASE CWDM SFP+ 40km Transceiver Modules 136
DWDM SFP Transceiver Modules 137
DWDM SFP+ Transceiver Modules 141
Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide
vii
Contents

10-Gigabit Ethernet XFP and 40-Gigabit QSFP Modules 143
DWDM XFP Transceiver Modules 144
APPENDIX B Site Log 147
Site Log 147
Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide
viii
Contents

Preface
This Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide preface contains these
sections:
•Changes to This Document, page ix
•Audience, page x
•Purpose, page x
•Document Organization, page x
•Documentation Conventions, page xi
•Obtaining Documentation and Submitting a Service Request, page xii
Changes to This Document
This table lists the technical changes made to this document since it was first developed.
Table 1: Changes to This Document
SummaryDate
Updated rear mounting installing sections and fan
tray sections to meet NEBS compliance requirements.
Added new section on installing and removing the
air filter.
March 2015
Added new optics supported in IOS XR Release 5.2.2.October 2014
Added new optics supported in IOS XR Release 5.1.2.September 2014
Added new optics supported in IOS XR Release 5.2.0.June 2014
Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide
ix

SummaryDate
Added information about how to install optional air
baffle accessory kit on the Cisco ASR 9001 Router.
Added information about the new Fast Ethernet SFP
modules, 10-GE SFP+ transceivers, and DWDM
SFP+ transceivers.
January 2014
Added information about Cisco ASR 9001-S Router.May 2013
Initial release of this document.June 2012
Audience
This guide is written for hardware installers and system administrators of Cisco routers.
These users must have a substantial background in installing and configuring router and switch-based hardware.
Also, they should be familiar with electronic circuitry and wiring practices, and have experience as an electronic
or electromechanical technician.
Purpose
This installation guide contains procedures for installing the router hardware, creating a basic startup
configuration file, and powering the router on for the first time.
Document Organization
This installation guide is organized into these chapters and appendixes:
•Preparing for Installation, on page 1, describes safety considerations, required tools and equipment,
an overview of the installation, and procedures to perform before installation.
•Unpacking and Installing the Chassis, on page 33, provides instructions for installing the chassis into
a rack.
•Installing Modules and Cables in the Chassis, on page 57, provides instructions for installing the cards
and modules into the chassis after it is mounted in a rack, and for connecting external network interface
cables.
•Troubleshooting the Installation, on page 85, provides guidelines for troubleshooting the router hardware
installation.
•Replacing Cisco ASR 9001 Router Components, on page 109, provides removal and replacement
procedures for primary router components and field-replaceable units (FRUs).
•Technical Specifications, on page 119, provides a summary of physical, electrical, and environmental
specifications for the router.
Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide
x
Preface
Audience