Citizen FS03 User manual

MOVEMENT SPECIFICATIONS
CAL.FS03/04
10-1/2 LIGNE, 3 EYES CHRONOGRAPH WITH HIGH HAN
D
ANALOGUE QUARTZ, 0 JEWEL
MANUFACTURED IN JAPAN
1.BASIC SPECIFICATION
S
(1) CaL. No. *TO CONFIRM WITH MOV'T DRAWING ATTACHED
CALIBRE
PUSHER
Ligne
Size*mm
Date
Total height
Figure
(push button
placed angle)
Battery & Life SR626SW 2YEARS
*
* based on 1 hour/day chronograph us
e
(2) Time standard
Type of quartz : Tuning fork type quartz crysta
l
Frequency : 32,768H
z
A
ccuracy : +/-20 s/month worn under normal circumstances
(3) Balanceable weight of hand
Minute hand Max. 0.4 μN.m
Second hand Max. 0.035 μN.m
Other small hands Max. 0.02 μN.m
(4) Function
Chronograph 1/1 sec. Basis (Up to 59 min. 59 sec.)
Powercell Saving Reset Mechanism(PSRM)
Over-loading Compensation Device(OLCD)
Digital Frequency Control(DFC) for time adjustment
Φ23.7X22mm (3H-9H)
O
10-1/2
*Eye position is the same as FS00 *Eye position is the same as FS01
4.15mm 4.28mm
FS03 FS04
FS03 FS04
SLANTED PARALLE
L
Parallel
Slanted
FS00/01
FS00/01
Center Hands
Height
Small Hands
Height

2.SEPARATED PART
S
Setting stem x1
Code 065-549
Length from movement center to far end 20.00mm
of setting stem
Thread................................. Ф0.9mm x 9.06mm
3.OTHERS
* Measurement of time rate
The unit(gate) time of measurement must be set at "10 sec." or integer fold
value of 10 sec. owing to the DFC system, and the measurement must be
performed in the form of complete watch.
* Marking on movement
JAPAN
MIYOTA CO.
FS03/04
NO JEWELS
* Typical clearance
Mov't - Caseback minimum 200 microns
Top of hands - Glass 300 - 400 microns *
* subject to the glass, case structure, and the length of hand
* Note
Please use aluminum material hand for Chrono second hand
* TACHYMETER
The tachymeter is the device which measures the speed of an automobile. Knowing is how
many seconds the car covers a distance of 1km, the meter can measure the approximate
average speed per hour during a journey (up to the maxinum measurable range of
tachymeter is 60 seconds.)
If the chronograph is started at the same time as measurement, and stopped after 1 km,
the average speed per hour can be determined according to the position of the second
hand. If the car covers the distance of 1km in 45 seconds, the average hourly speed during
the journey will be about 80 km.

4 INSTRUCTION MANUAL
A
) DISPLAYS AND BUTTONS
B) SETTING THE TIME
1. Pull the crown to the 2nd Click Position.
2. Turn the crown to set the hour and minute hands.
C) SETTING THE DATE
* If the date is set between the hours of around 9:00 PM and 1:00 AM, the date may
not change on the following day.
1. Pull the crown to the 1st Click Position.
2. Turn the crown by clockwise to set the date.
3. After the date has been set, push the crown back to the normanl position.
D) USING THE CHRONOGRAPH
This chronograph is able to measure and display time in 1/1 second united up to
maxinum of 1 hour.
Measuring time with the chronograph
1. The chronograph can be started and stopped each time button "PB1" is pressed.
2. To reset, press button "PB2" and the chronograph second & minute hands return to the 0 positions.
RESET "PB1" TIME MEASUREMENT STOP
"PB2" "PB1"
"PB2"
Chronograph
Minute
Hand
Hour Hand
Small
second
h
a
n
d
Chronograph Second
Minute Hand
PB1
PB
24Hour
Normal Position
1st Click Position
2nd Click Position
Chronograph
Minute
Hand
Hour Hand
Small
second
h
a
n
d
Chronograph Second
Minute Hand
PB1
PB
24Hour
Normal Position
1st Click Position
2nd Click Position

E) CHRONOGRAPH RESET (INCL. AFTER REPLACING BATTERY)
This procedure shoud be performed when the chronograph second hand
do not return to the 0 second position after the chronograph has been reset,
and including after the battery has been replaced.
1. Pull the crown to the 2nd Click Position.
2. Press the button "PB1" once to set the chronograph second hand ahead one scale,
or keep pushing to set the chronograph second hands quickly.
3. Once the chronograph second hand has been zeroed, reset the time and return the crown to its
normal position.
* Do not return crown to normal position while chronograph second hand
return to 12:00 (ZERO) position.
Hand stops on the way when crown are returned to normal position and these
positions are recognized as 12:00 (ZERO) position.
These specifications might be changed without prior notice.
Chronograph
Minute
Hand
Hour Hand
Small
second
h
a
n
d
Chronograph Second
Minute Hand
PB1
PB
24Hour
Normal Position
1st Click Position
2nd Click Position