Citizen HIGH HAND CHRONOGRAPH Series User manual

<TIME STANDARD>
Type of quartz: Tuning fork type quartz crystal
Frequency : 32,768Hz
Accuracy : ±20 second / month worn under normal circumstances
< Balanceable weight of hand >
Minute hand Max. 0.4 μN.m
Second hand Max. 0.035 μN.m
Other small hands Max. 0.02 μN.m
< Function >
Chronograph 1/1 sec. Basis (Up to 59 min. 59 sec.)
Powercell Saving Reset Mechanism(PSRM)
Over-loading Compensation Device(OLCD)
Digital Frequency Control(DFC) for time adjustment
Overall diameter
FS23 / FS24FS13 / FS14
eye position is same as FS00/01
*based on 1 hour/day chronograph use
FS00 / FS01
Φ23.3mm×21.8mm
CENTER HANDS SMALL HANDSCENTER HANDS SMALL HANDS SMALL HANDSCENTER HANDS SMALL HANDS
FS03 / FS04
10 1/2'''
eye position is same as FS20/21
CENTER HANDS
Φ23.7mm×21.8mm
Φ23.3mm×21.8mm Φ23.3mm×22.0mm
Φ23.7mm×21.8mm
Ligne
SR626SW 2YEARS *
FS24
HIGH HAND
SLANTED PARALLEL
5.10mm 5.25mm
FS14
HIGH HAND
PARALLEL
FS03
HIGH HAND
5.25mm
CAL.
Push Buttons
Total height 5.10mm
Cal. FS13/14 FS23/24
HIGH HAND CHRONOGRAPH SERIES
FS13
HIGH HAND
SLANTED
FS23
HIGH HAND
FS04
HIGH HAND
SLANTED PARALLEL
4.13mm 4.28mm
Case fitting diameter
Date
Bateery & Life
○
eye position is same as FS10/11
Φ23.7mm×22.0mm Φ23.7mm×22.0mm
Φ23.3mm×22.0mm
Φ23.7mm×22.0mm
Φ23.3mm×22.0mm
Φ23.7mm×21.8mm
Φ23.3mm×21.8mm
1. Basic Specification
new new new new
300μ
400μ
1200μ
400μ
1750μ
350μ
750μ
400μ
300μ
1600μ
400μ
300μ
1600μ1200μ1300μ1200μ
normal hands

* Measurement of time rate
The unit(gate) time of measurement must be set at "10 sec." or integer fold value of 10 sec. owing to the
DFC system, and the measurement must be performed in the form of complete watch.
* Marking on movement
JAPAN
MIYOTA CO.
( CAL. NO.)
NO JEWELS
* Typical clearance
Mov't - Caseback minimum 200 microns
Top of hands - Glass 300 - 400 microns *
* subject to the glass, case structure, and the length of hand
* Note
Please use aluminum material hand for Chrono second hand
* TACHYMETER
The tachymeter is the device which measures the speed of an automobile. Knowing is how many seconds the car
covers a distance of 1km, the meter can measure the approximate average speed per hour during a jorney ( up to
the maxinum measurable range of tachymeter is 60 seconds.)
If the chronograph is started at the same time as measurement, and stopped after 1 km, the average speed per hour
can be determined according to the position of the second hand. If the car covers the distance of 1km in 45 seconds,
the average hourly speed during the journey will be about 80 km.
065- 549 ×1
Setting stem
L
engt
h
f
rom movement
center to far end of setting
stem
20.00mm
Thread Ф0.9mm×9.06mm
2. Separated Parts
3. Others

【
Displays and Buttons
】
A) SETTING THE TIME
1. Pull the crown out to the 2nd Click Position.
2. Turn the crown to set the hour and minute hands.
B) SETTING THE DATE
* If the date is set between the hours of around 9:00 PM and 1:00 AM, the date may not change on the
following day.
1. Pull the crown out to the 1st Click Position.
2. Turn the crown clockwise to set the date.
3. After the date has been set, push the crown back to the normanl position.
C) USING THE CHRONOGRAPH
This chronograph is able to measure and display time in 1/1 second united up to maximum of 1 hour.
【Measuring time with the chronograph】
1. The chronograph can be started and stopped each time button "PB1" is pressed.
2. To reset, press button "PB2" and the chronograph second & minute hands return to the zero positions.
E) CHRONOGRAPH RESET (INCL. AFTER REPLACING BATTERY
)
This procedure shoud be performed when the chronograph second hand do not return to the zero second
position after the chronograph has been reset, and including after the battery has been replaced.
1. Pull the crown to the 2nd Click Position.
2. Press the button "PB1" once to set the chronograph second hand ahead one scale, or keep pushing to
to set the chronograph second hands quickly.
3. Once the chronograph second hand has been zeroed, reset the time and return the crown to its normal
position.
* Do not return crown to normal position while chronograph second hand return to 12:00 ( ZERO ) position.
Hand stops on the way when crown are returned to normal position and these positions are recognized a
s
12:00 (ZERO) position.
These s
p
ecifications mi
g
ht be chan
g
ed without
p
rior notice.
4. Instruction Manual
PB 2
Reset Time
Measurement Stop
PB
PB
PB
PB
Normal Position
1st Click Position
2st Click Position
Chronograph
Second Hand
Chronograph
Minutes Hand
Small Second Hand
PB 1
24 Hour Hand