Clarke DEVIL 2000PTC-B Instruction Manual

.
OPERATION & MAINTENANCE
INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC03/23ORIGINAL INSTRUCTIONS GC03/23
2KW ELECTRIC FAN HEATER
MODEL NO: DEVIL 2000PTC-B
PART NO: 6925591

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE product. Please read this manual
carefully, in doing so you guarantee the safety of yourself and that of others
around you, and you can look forward to your purchase giving you long and
satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt as proof of
purchase.
This guarantee is invalid if the product is found to have been abused,
tampered with, or not used for the purpose for which it was intended. Faulty
goods must be returned to their place of purchase, no product can be
returned to us without prior permission.
This guarantee does not effect your statutory rights.
PRODUCT SPECIFICATIONS
Product: Depth x Width x Height 210 x 160 x 217 mm
Product weight 1.6 kg
Operating Voltage and Frequency: (V / Hz) 230 V / 50Hz
Required power; Fan only
Fan& heat setting 1
Fan& heat setting 2
0.11 A
4.94 A
8.89 A
Operating Temperature: (Min/Max) (°C): -15 to 25°C
Heat Output: (kW): Fan only
Fan& heat setting 1
Fan& heat setting 2
0.025 W
1 kW
2 kW
Max Air Output: (m3/h) 197m3/h
Safety Device: Thermal cut-out
Duty Cycle Classification: S1 Continuous duty
Electrical Insulation Class I
Ingress Protection rating IP20

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
THE FOLLOWING TABLE ADDRESSES THE
INFORMATION REQUIREMENTS OF REG.2015/1188
Item Symbol Value Unit
Heat output
Measured seasonal space heating energy efficiency 36%
Nominal heat output Pnom 2.0 kW
Minimum heat output (indicative) P min 1.0 kW
Maximum continuous heat output P max 2.0 kW
Auxiliary electricity consumption
At nominal heat output elmax n/a kW
At minimum heat output el min n/a kW
In standby mode elSB n/a kW
Type of heat input for electric storage local heaters only
Manual heat charge control with integrated thermostat No
Manual heat charge control with room and/or outdoor temperature
feedback
No
Electronic heat charge control with room and/or outdoor temperature
feedback
No
Fan assisted output No
Type of heat output/room temperature control (select one)
Single stage heat output, no temperature control No
Two or more manual stages, no temperature control No
With mechanical thermostat temp control Yes
With electronic temperature control No
Electronic temperature control with day timer No
Electronic temperature control with week timer No
Other control options (multiple selections possible)
Room temperature control with presence detection No
Room temperature control with open window detection No
Room temperature control with distance control option No
Room temperature control with adaptive start control No
Room temperature control with working time limitation No
Room temperature control with black bulb sensor No

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
SAFETY
Make sure that you read, understand and comply with the following
guidance. These safety symbols should appear on the heater.
GENERAL
•DO NOT operate the heater when you are tired or under the influence of
alcohol, drugs or intoxicating medication.
•DO NOT stand on the heater.
•DO NOT use the heater with wet hands or when there is water on the
power cable.
• Turn the heater off when not in use and keep it in a safe, dry, childproof
location.
• The heater is designed to heat enclosed areas such as workshops and
other industrial areas. DO NOT use the heater for any other function. It is
not suitable for drying clothes or laundry.
ELECTRICAL SAFETY
• Regularly inspect the power cable / plugs for damage/looseness. DO
NOT use the heater it the power cable is damaged.
• Minimise the risk of electric shock by installing a RCCB (Residual Current
Circuit Breaker) and a suitable isolator into the main distribution board.
• Make sure that the voltage on the rating label is the same as the voltage
of the power supply. If in doubt, consult a qualified electrician.
•DO NOT abuse the electrical cable. DO NOT use the cable for pulling or
unplugging the heater.
• Keep the cable away from sources of heat, oil, sharp edges or moving
parts. Damaged or tangled cables increase the risk of electric shock.
•DO NOT use extension cables with this heater.
Hot Surface,
Do Not Touch
Read the
manual
Do Not Cover

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
POSITIONING
• This heater is designed for indoor use only.
•DO NOT place the heater close to a bath, wash basin, shower, swimming
pool or any other water-filled area or wet surface. DO NOT place the
heater against any surface such as a wall, door or furniture etc.
•DO NOT place the heater immediately below any electrical outlet.
•NEVER place the heater near combustible materials etc. Allow 2 metres
clearance all round this heater.
•DO NOT place the heater on a raised surface or anywhere it could
topple over.
• Take care to ensure that the grille cannot be blocked.
•DO NOT operate fan heater in explosive atmospheres such as in the
presence of flammable liquids, gasses or dust such as in a paint spray
booth, or any explosive environment. Electric motors create sparks
which may ignite dust or fumes.
OPERATION
• The heater must only be used by people who have read these
instructions and have been trained in its use.
•DO NOT obstruct the air inlet and outlet sections of the heater.
•DO NOT cover the heater.
•DO NOT touch the heater casing or grille when first switched off, as these
will be very hot and will take time to cool.
•DO NOT get the heater wet or use in areas of high condensation.
•DO NOT allow the power lead to touch hot surfaces.
•DO NOT connect other appliances to the same mains socket as the
heater.
• Only use the heater in a level position.
•DO NOT use this heater with a programmable timer used to switch it on
automatically.
WARNING: DO NOT USE THE HEATER NEAR FLAMMABLE MATERIAL,
LIQUIDS, SOLIDS, GASSES OR COMPRESSED GAS CYLINDERS ETC.

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
ELECTRICAL CONNECTIONS
Before switching the product on, make sure that the voltage of your electricity
supply is the same as that indicated on the rating plate. Connecting it to any
other power source may cause damage.
If it is necessary to change the fuse in the plug, the fuse cover must be refitted.
If the fuse cover becomes lost or damaged, the plug must not be used until a
suitable replacement is obtained.
If the plug has to be changed due to damage, a replacement should be
fitted, following the wiring instructions shown below. The old plug must be
disposed of as insertion into a mains socket could cause an electrical hazard.
If the colors of the wires in the power cable of this product do not correspond
with the markings on the terminals of your plug, proceed as follows.
•TheBlue wire must be
connected to the
terminal which is
marked Nor coloured
Black.
•TheBrown wire must
be connected to the
terminal which is
marked Lor coloured
Red.
•TheYellow/Green wire
must be connected to
the terminal which is marked Eor coloured Green.
We strongly recommend that this machine is connected to the mains supply
via a Residual Current Device (RCD)
If in any doubt, consult a qualified electrician. DO NOT attempt any repairs
yourself.
WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY
BEFORE CONNECTING THE HEATER TO THE MAINS SUPPLY.

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
OPERATION
1. Place the heater in a level position
on a flat surface and at a safe
distance from flammable
materials. Keep 2m clearance all
round.
2. Connect the heater to a suitable
power supply.
3. Set the thermostat control to the
maximum setting (fully clockwise).
4. Set the mode selector to one of
the following settings:
• The heater will take up to three minutes to reach optimum temperature.
5. Once the room reaches the required temperature, turn the thermostat
control slowly counter-clockwise until the thermostat clicks, leave the
control in this position.
• The room temperature will be maintained at this setting. The heater will
continue to operate until the power switch is turned to the OFF position.
WARNING: DO NOT USE THIS HEATER IN SMALL ROOMS WHEN THEY ARE
OCCUPIED BY PERSONS NOT CAPABLE OF LEAVING THE ROOM ON THEIR
OWN, UNLESS CONSTANT SUPERVISION IS PROVIDED.
CAUTION: PARTS OF THIS HEATER CAN BECOME VERY HOT AND CAUSE
BURNS. PARTICULAR ATTENTION HAS TO BE GIVEN WHERE CHILDREN
AND VULNERABLE PEOPLE ARE PRESENT.
Off
Fan Only
Fan + Heat Setting 1
Fan + Heat Setting 2

8
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
6. For fan only operation, turn the power switch to the fan only setting and set
the thermostat to its minimum setting.
7. When not in use, disconnect the heater from the mains supply. Store it in a
safe, dry, childproof location.
ADJUSTING THE ANGLE
1. Loosen both adjusting knobs.
2. Adjust to the required angle.
3. Retighten the adjusting knobs.
THERMOSTATIC PROTECTION
The Devil 2000PTC has a thermal cut
out to prevent it from overheating.
If the temperature of the front grille
gets too high the thermal cutout will
turn off the heating elements. When
the fan has cooled the unit sufficiently, normal operation will resume.
FAULTFINDING
Problem Possible Cause Remedy
Heater does not
operate,
although
plugged in with
the switch and
thermostat
switched on.
Plug is loose/bad
connection.
Pull the plug out & check the
connection of the plug and socket.
Fuse blown or
circuit breaker trips.
Replace if necessary and investigate
cause. If fuse blows repeatedly, consult
your Clarke dealer.
No power at socket Insert the plug in a functioning socket
Heating element
glowing hot.
Input voltage too
high.
Use a power supply in accordance
with the rating on the label.
Air inlet grille is
blocked
Ensure the heater is kept away from
any objects which could cover the air
inlet or be drawn into it.
Heater has
failed to heat up
so only the air
fan has
operated.
Control switch not
set at a "HEATING"
level.
Turn switch to a heating level.
Thermostat has
tripped.
Turn the thermostat and listen. If there is
no CLICK and the thermostat is not
damaged, the heater will
automatically switch ON when it has
cooled down.
Abnormal noise Heater is not level. Stand heater on a level surface

9
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
MAINTENANCE.
• Check that the heater is in good working order. Take immediate action
to repair or replace damaged parts.
•DO NOT allow the heating elements to become covered with dust
which could become a fire hazard. If used in a dusty workplace it should
be cleaned after every use with a dust extractor.
• ONLY recommended parts should be used. Unapproved parts may be
dangerous and will invalidate the warranty.
•DO NOT attempt to repair a damaged heater, contact the CLARKE
service department.
• Clean the heater with a soft damp cloth once cold. DO NOT use
solvents or abrasives
• No other maintenance is required, should you discover any problem
with the heater, return it to the CLARKE service department for repair.
SERVICE & REPAIRS
Have your heater repaired by a qualified person using identical replacement
parts. This will ensure that the safety of the heater is maintained.
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the obligation to
deal with the WEEE in accordance with the WEEE regulations in relation to the
treatment, recycling & recovery and environmentally sound disposal of the
WEEE.
• In effect, this means that this product must not be discarded with
general household waste. It must be discarded according to the laws
governing Waste Electrical and Electronic Equipment (WEEE) at a
recognized disposal facility.
WARNING: SERVICING OR INTERNAL MAINTENANCE MUST ONLY BE
CARRIED OUT BY THE CLARKE SERVICE DEPARTMENT.
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY AND ALLOW
THE HEATER IT TO COOL DOWN BEFORE PERFORMING ANY
MAINTENANCE TASKS.

10
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
COMPONENT PARTS
NO DESCRIPTION NO DESCRIPTION
1 Front Grille 12 Control Box
2 Air Outlet 13 Outer Casing
3 PTC Heating Element 14 Cable Fastener
4 Air Flue 15 Back Grill
5 Motor 16 Power Cable
6Fan 17Screw
7 Adjustable Thermostat 18 Rubber Gasket
8 Rotary Switch 19 Steel Pipe
9 Control Knob 20 Feet
10 Indicator Lamp Cover 21 Self-Setting Thermostat
11 Thermostat Knob 22 Thermal Protection

11
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATIONS OF CONFORMITY