Classic Exhibits Perfect 10 User manual

www.classicexhibits.com
Step 1
Page 1 of 8
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL BLACK KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - P20 - Ben Jamin - General Layout

www.classicexhibits.com
Step 1
Page 1 of 8
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL BLACK KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - P20 - Ben Jamin - Backwall Assembly
Part Number
1
2
3A
3
4
Step 1:
NOTE: Can be assembled either face down on floor then lifted
upright or upright as shown in drawings.
A) Connect vertical leg assemblies [1 and 2] together by connecting horizontal extrusions
[4] between assemblies tightening BLACK knobs on backside of extrusion making sure Velcro
faces toward BACK and placing it about one inch up from bottom and tightening.
B) Connect vertical extrusions [3 and 3A] to leg assemblies [1 and 2] using vertical connection
bar as shown.
C) Connect upper horizontal extrusion [4] between verticals [3 and 3A] placing it about one
inch down from top.
NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully
engage, gently rock lock and extrusion while turning knob until lock fully opens.
Description
Left Leg Assembly w/ A10 Clamps Attached
Middle Leg Assembly
Upper Curved Vertical w/ A10 Clamps Attached
Upper Curved Vertical
23”w Horizontal
1
2
3A
3
4
4
Black
Knob
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of
knobs on BACKSIDE of unit.
Vertical
Connection Bar
NOTE:When assembling horizontals they should
be placed approximately one inch from TOP and BOTTOM.
Slide
horizontal into groove
Assure
that a good
connection is made
and tighten to secure.
Slide Connection Bar into lower
leg assembly. Slide upper vertical
over bar and secure both.
Rear View of Display
Step 1
Step stool may be required
for assembly.

www.classicexhibits.com
Step 2
Page 2 of 8
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL BLACK KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - P20 - Ben Jamin - Backwall Assembly cont’d
Step 2:
NOTE: Can be assembled either face down on floor then lifted
upright or upright as shown in drawings.
A) Connect vertical extrusion [6] to leg assembly [5] using vertical connection bar as shown.
B) Connect horizontal extrusions [7 and 8] between vertical assemblies by tightening
BLACK knobs on backside of extrusion making sure Velcro faces toward BACK.
NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully
engage, gently rock lock and extrusion while turning knob until lock fully opens.
1
2
3A
3
4
4
Black
Knob
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of
knobs on BACKSIDE of unit.
Hinge Extrusion
Top Horizontal Hinge faces down.
Bottom Horizontal Hinge faces up.
NOTE:When assembling horizontals they should
be placed approximately one inch from TOP and BOTTOM.
Slide
horizontal into groove
Assure
that a good
connection is made
and tighten to secure.
5
6
7
8
Slide Connection Bar into lower
leg assembly. Slide upper vertical
over bar and secure both.
Rear View of Display
Step 2
Part Number
5
6
7
8
Description
Right Leg Assembly
Upper Curved Vertical
69”w Horizontal w/ Hinge Facing UP
69”w Horizontal w/ Hinge Facing DOWN

www.classicexhibits.com
Step 3
Page 3 of 8
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL BLACK KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - P20 -
Part Number
9
10
11
12
Step 1:
NOTE: Can be assembled either face down on floor then lifted
upright or upright as shown in drawings.
A) Connect vertical extrusion [10] to leg assembly [9] using vertical connection bar as shown.
B) Connect horizontal extrusions [11 and 12] between vertical assemblies by tightening
BLACK knobs on backside of extrusion making sure Velcro faces toward BACK.
NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully
engage, gently rock lock and extrusion while turning knob until lock fully opens.
Description
Middle Leg Assembly
Upper Curved Vertical
69”w Horizontal w/ Hinge Facing UP
69”w Horizontal w/ Hinge Facing DOWN
5
9
6
10
11
12
Black
Knob
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of
knobs on BACKSIDE of unit.
Vertical
Connection Bar
NOTE:When assembling horizontals they should
be placed approximately one inch from TOP and BOTTOM.
Slide
horizontal into groove
Assure
that a good
connection is made
and tighten to secure.
Slide Connection Bar into lower
leg assembly. Slide upper vertical
over bar and secure both.
Rear View of Display
Step 3
Step stool may be required
for assembly.
Hinge Extrusion
Top Horizontal Hinge faces down.
Bottom Horizontal Hinge faces up.
Ben Jamin - Backwall Assembly (Cont’d)

www.classicexhibits.com
Step 4
Page 4 of 8
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL BLACK KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - P20 -
Step 2:
NOTE: Can be assembled either face down on floor then lifted
upright or upright as shown in drawings.
A) Connect vertical extrusion [14] to leg assembly [13] using vertical connection bar as shown.
B) Connect horizontal extrusions [15] between vertical assemblies by tightening
BLACK knobs on backside of extrusion making sure Velcro faces toward BACK.
NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully
engage, gently rock lock and extrusion while turning knob until lock fully opens.
5
9
6
10
11
12
Black
Knob
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of
knobs on BACKSIDE of unit.
NOTE:When assembling horizontals they should
be placed approximately one inch from TOP and BOTTOM.
Slide
horizontal into groove
Assure
that a good
connection is made
and tighten to secure.
15
14
13
15
Slide Connection Bar into lower
leg assembly. Slide upper vertical
over bar and secure both.
Rear View of Display
Step 4
Part Number
13
14
15
Description
Right Leg Assembly w/ A10 Clamps Attached
Upper Curved Vertical w/ A10 Clamps Attached
23”w Horizontal
Ben Jamin - Backwall Assembly (Cont’d)

www.classicexhibits.com
Step 5
Page 5 of 8
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL BLACK KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - P20 - Ben Jamin - Blade and Wing Assembly
Hex Key Tool Flathead
Screwdriver
(if necessary)
Slide A10 Clamp into groove
of square extrusion.
When desired location is
found, tighten set screw
to secure.
Set-
Screw
A10
Tighten black plastic set screw
to secure Wing in place.
Black Plastic
Set-screw
Decorative Blade Attachment
(if accidently removed)
Attach decorative wing and
blades to A10’s attached to
Backwall as shown.

www.classicexhibits.com
Step 6
Page 6 of 8
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL BLACK KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - P20 - Ben Jamin - Header, Shelf and Cubby Assembly
Light Connection
Attach Lights to
Backwall where
desired and tighten
in place.
Shelf attaches to section
5 by setting atop pins
located on right side
and securing into place
with thumbscrew on left.
Cubby Attachment
Slide onto back pin first.
When attaching counter you will need to first
slide shelf onto back pin then set down on front
pin.
Accessary Attachment
Accessary Attachment
Attach Header support to Backwall
then attach header to support by Velcroing it.
Header
Pins
Thumbscrew
Shelf attaches to back of
sections 1 and 2 by setting
atop pins located on back left
side.
Header
Header

www.classicexhibits.com
Step 7
Page 7 of 8
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL BLACK KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - P20 - Ben Jamin - Workstation Assembly - Qty. 2
Part Number
A
B
C
D
Step 1:
A) Connect lower horizontal extrusion [C] between bottom of leg assemblies [A and B] as shown.
B) Insert Laminated infill into grooves of leg assemblies [A and B].
C) Attach extrusion door between leg assemblies [A and B] and atop laminated infill.
D) Attach upper horizontal extrusion w/ door stopper [D] between leg assemblies [A and B],
and set flush with top of legs [A and B].
Description
Left Leg Assembly
Right Leg Assembly
Horizontal Extrusion
Horiontal Extrusion w/ Door Stopper
Black
Knob
Turn Knob Clockwise
to Tighten Lock
DOOR
Laminated Infill
A (left)
B (right)
C
D (w/ Door Stopper)
Knobs face INSIDE
of workstation
Knobs face INSIDE
of workstation
Knobs face FORWARD
Pins are
located on INSIDE
FRONT vertical
of Leg
Assemblies
NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully
engage, gently rock lock and extrusion while turning knob until lock fully opens.
Align with bottom of leg assemblies [A and B].

www.classicexhibits.com
Step 8
Page 8 of 8
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL BLACK KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - P20 - Ben Jamin - Workstation Assembly cont’d
Part Number
E
F
Step 2:
A) Attach horizontal extrusion [E] between vertical leg assemblies [A and B] as shown below.
B) Insert Laminated infill into grooves of vertical leg assemblies [A and B].
C) Attach upper horizontal extrusion [F] between vertical leg assemblies [A and B] atop infill.
D) Place internal shelf into assembled pedestal atop pins.
E) Set Counter atop assembled pedestal and secure with Velcro straps attached to underside of top.
Description
Horizontal Extrusion
Horizontal Extrusion
E
Laminated
Infill
Knobs facing FORWARD
Place internal shelf into
workstation then
place counter atop
assembled workstation.
Internal
Shelf
F
Knobs face INSIDE
of workstation

www.classicexhibits.com
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL BLACK KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - P20 -
Level 1
Level 2
Level 3
Level 4
Level 5
Top View of each Level
Blade Wing
Vertical Connection Bar
Horizontal Extrusions
Wing Attachment
Case #1 - Backwall Components
Leg Assembly
Leg Assembly
Leg Assembly
Vertical Connection Bar
Vertical Connection Bar
Horizontal Extrusion
Horizontal Extrusion
A10’s
Attached
Cutout
for A10 Clamp
Cutout
for A10 Clamp Cutout
for A10 Clamp
Header Supports
Header
Ben Jamin - Backwall Case Packing - 6 Total Cases