Classic Exhibits visionary DESIGNS VK-1131 Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
10’
VK-1131 - 10’ x 10’ Display
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Order #XXXXX
Straight Connection
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Straight Connector
Straight Connector
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
CEI110 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
CEI110 Frame Assembly

© 2023
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation

© 2023
Crate 1 of 5
Order #XXXXX
Locked layer contains
placeholder marks.
CRATE PACKING
Crate Packing

© 2023
Step 1 of 5
Order #XXXXX
Locked layer contains
placeholder marks.
12
3
68
13
5
FRONT VIEW
Item
1
2
3
4
5
6
10
13
Qty.
1
1
1
1
1
1
1
2
Description
87”h CEI110 Vertical Extrusion
87”h CEI110 Vertical Extrusion
28”w CEI110 Horizontal Extrusion
74”w CEI110 Horizontal Extrusion
28”w CEI110 Horizontal Extrusion
28”w CEI110 Horizontal Extrusion
86.252”h GS300 Vertical Extrusion
6” x 22” Base Plate
10
13
Steps:
Refer to the CEI-110 Frame Assembly general information page.
1) Assemble horizontals [3-5] & [6-8] together.
2) Connect verticals [1,2] between horizontal assemblies [3/5] & [6/8].
3) Connect vertical [10] between horizontal assemblies [3/5] &
[6/8]. See GS300 Attachment detail.
4) Install Base Plates [13] to bottom horizontals, using bolts & wing nuts.
When assembled
TOP VIEW
5.7”
CEI-110
GS300
GS300 Attachment
Attach GS300 vertical to front
groove of CEI-110 horizontal.
*
FRONT VIEW
Middle Frame Assembly

© 2023
Step 2 of 5
Order #XXXXX
Locked layer contains
placeholder marks.
FRONT VIEW
Steps:
1) Connect power cords to Supernova lights, as shown.
Transformer Transformers
Power
Break
Power
Break
++
--
Lights Male
Light to Light Attachment
Maximum of 7 lights per chain,
11 lights per Transformer
Light to Transformer Attachment
+
-
Power
Female
Transformer
144W / 6 Amp / 24V
Lightbox Wiring

© 2023
Step 3 of 5
Order #XXXXX
Locked layer contains
placeholder marks.
Item
1
2
3
4
5
6
7
8
Qty.
1
1
1
1
1
2
1
1
Description
90”h CEI110 Vertical Extrusion
51.962” CEI110 angled Extrusion
51.962” CEI110 angled Extrusion
73.019”w CEI110 Horizontal Extrusion
73.019”w CEI110 Horizontal Extrusion
86.353”h Z45 Vertical Extrusion
86.353”h Z45 Vertical Extrusion
Corner Base Plate
bolt
wing
nut
bolt
bolt
key hole
Corner Base Plate Attachment
*Place key hole over bolt
on vertical extrusion and
slide down; secure with
bolts & wing nuts.
FRONT VIEW
1
2
3
4
5
66
8
7
*
***
***
Assemble frame flat on ground.
Steps:
Refer to the CEI-110 Frame Assembly general information page.
1) Assemble angled extrusions [2-3] together using custom angle
corner connector.
2) Attach verticals [1], [2/3] between horizontals [4,5].
3) Connect verticals [6,7] between horizontals [4,5].
See Z45 Attachment detail.
4) Attach Corner Base Plate to extrusions [1,4] as shown.
See Corner Base Plate Attachment detail.
CEI-110
Z45
Z45 Attachment
Attach Z45 vertical to back
groove of CEI-110 horizontal.
*
FRONT VIEW
When assembled
Left Frame Assembly

© 2023
Step 4 of 5
Order #XXXXX
Locked layer contains
placeholder marks.
Item
--
--
Qty.
2
4
Description
1” Standoff Barrel w/ V20
3.5” Standoff Barrel
When assembled
Standoff Barrel Attachment
*
Standoff
Barrel
Slide connector on back of standoff barrel
into groove of extrusion. Twist to secure
in place.
Note: Standoff Barrel attaches through SEG Graphic.
S
E
G
Gra
p
h
i
c
Note: Monitor mount installs over SEG graphic.
Bolts
Monitor Mount
Z45
Z45
Monitor Mount Attachment
*
Attach Standoff Barrels to verticals using
bolts from back side of extrusions. Then
attach Monitor Mount to front of Standoff
Barrels, using bolts.
3.5”
Stand-Off
Barrels
Bolts
7
66
10
13
SEG Grap
h
ic
SEG
B
lo
c
k
e
r
SEG Grap
h
ic
*
*
**
Steps:
Refer to the SEG Installation general information page.
1) Apply SEG Graphic to front of Lightbox assembly.
2) Attach 1” Standoff Barrels to vertical [10] of Lightbox assembly.
See Standoff Barrel Attachment detail.
3) Connect Front Frame vertical [7] to Standoff Barrels, using bolts.
4) Attach Front Frame horizontal [4] to base plate [13] using bolts & wing nuts.
5) Apply SEG Graphic to Front Frame assembly.
6) Install Monitor Mount to verticals [6] of Front Frame assembly,
using 3.5” Standoff Barrels. See Monitor Mount Attachment detail.
7) Apply SEG Blocker to back of Lightbox assembly.
4
Frames Connection