Classic Exhibits visionary DESIGNS MOD-1180 User manual

www.classicexhibits.com
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1180 - Workstation Assembly
Item
1
2
3
4
Description
Tapered Panel w/ Door
Side Panel
Tapered Panel
Side Panel
Qty.
1
1
1
1
Item
1
2
3
4
Description
Base Plate
Right Leg Extrusion
Left Leg Extrusion
Vertical Extrusion for Monitor Mount Attachment
Qty.
1
2
2
1
1
2
3
4
1
22
3
3
Steps:
1) Attach left leg extrusions [3] to panel [2] and right leg
extrusions [2] to panel [4] using supplied screws,
see detail illustration below.
2) Assemble panels [1and 3] to panels
[2and 3] as shown.
Steps (Cont’d):
3) Attach leg assemblies to base plate [1]
using bolts as shown.
4) Attach pins to back of panels [1and 3],
then set floor atop pins.
5) Velcro shelf supports to inside of
assembled base, then set shelf atop
supports.
6) Attach plate to underside of counter, and
secure with provided screws.
7) Attach vertical extrusion [4] to counter
using supplied bolt.
8) Set counter atop assembled
base.
9) Attach monitor mount to vertical extrusion
where indicated, see monitor mount
attachment detail.
4
Modul Extrusion: Part List
EURO LT System: Part List
Monitor Mount Attachment
Attach monitor mount to vertical
extrusions after assembly.
Slide Mount
into Groove of
Vertical Extrusion.
Tighten
Setscrew Attach top
Plate and
tighten screws
*
*
Screws
Screws
Screws
Screws
2
3
3
4
2
2
Shelf Supports
Shelf
Counter Top
Step 1 Step 1 Step 3
Step 4
Step 5
Step 6
Step 7
Floor
Attach pins to lower BACK
side of panels [1and 3]
for floor placement.
Step 2

www.classicexhibits.com
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool
Typical Connection Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most exhibits can be assembled
with the supplied Hex Key Tool.
Occasionally, a flat head screw-
driver may be required.
Most horizontal extrusion connections have a patented expandable lock.
This lock inserts into the groove of an opposing extrusion. Tightening the
lock with the Hex Key Tool expands the lock and creates a strong positive
connection.
Remove only (1) setscrew when disassembling.
Replace setscrew in extrusion after assembling it.
Before packing, replace setscrew in extrusion to
avoid losing it.
Attach base plate to round or
square vertical extrusion using
the bolt provided. Be careful not
to strip the threads.
When vertical extrusions are
packed in portable cases rather
than crates or tubs, they must be
broken down into smaller sections
which then require assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews
in extrusion after assembling it.
Before packing, replace setscrews
in extrusion to avoid losing them.
Using Your Setup Instructions
The Euro LT Hybrids Setup Instructions are created specifically for your configuration.
They are laid out sequentially in levels, including exploded views, and a logical series of
detailed steps to assemble the main structure and components. We encourage you to study
the instructions before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your exhibit to prevent loss of
the locks and setscrews (see below in RED). This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) When cleaning laminate inserts, countertops, or panels use mild cleansers and a soft material such
as cotton.
3) Keep all display components away from extreme heat and long exposure to sunlight to avoid
warping and fading.
4) Retain all packing material. It will make re-packing much easier and will reduce the likelihood of
shipping damage.
Typical Connection (cont’d) Numbered Label
Each extrusion contains a numbered
label which corresponds with setup
instructions. The label is located within
a groove of the extrusion (when possible).
With extrusion components the labels
contain Black numbers unless otherwise
specified.
Detail C Detail D Detail EDetail B
Detail A
Setscrews
Cut Away View Of
Slide Clips
Left
Panel
Right
Panel
Left Hand
Grasps Panel
Firmly
With Right Hand Thumb
Close to Seam
Squeeze,
Push Forward,
And Lift
Color Coded Clip
w/ assembly number
Panel Lock
When Required
Black Clip
is bottom of
panel
Connector Top View of Panels with LocksExample of Connection
Color Coded Clip
w/ assembly number
Panel Lock
When Required
Each component has 2 clips,
the lower clip is ALWAYS
black. The top clip is color
coded to distinguish the
level. The color coded clip
also contains the numbered
label.
Components connect together
by aligning them and sliding
downward connecting clips
together.
Configurations are assembled
from left to right, usually starting
with #1 and following the
numbered sequence.
The first level of components contains panel locks
that are located at the top of the panel for extra
stability and a seamless connection. When dis-
assembling panels, twist top connection slightly
and lift right panel upward.
General Setup Instructions for Extrusion System
General Setup Instructions for Panel System
Level 1 = Blue
Level 2 = Red
Level 3 = Green
Level 4 = Black

www.classicexhibits.com
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Case Packing Instruction
Tapered Panel
Slip Sheet
Counter Top
Floor and Internal Shelf
Tapered Panel
Side Panel x 2
Base Plate
Round Extrusion x 5