Claudgen RCT250SL Use and maintenance manual

Installation & Control Guide for
Radiant Ceiling Tile Heater for SL Wireless Controllers
All electrical appliances produced by the Company are guaranteed for one year
against faulty materials or workmanship. This applies only if the appliance has been
used for purposes in accordance with the instructions provided and has not been
connected to an unsuitable electricity supply, or subject to misuse, neglect,
damage or modified or repaired by any person not authorised by us. This guarantee
is offered to you as an extra benefit and does not affect your legal rights.
The correct electricity supply voltage is shown on the rating label attached to the
appliance.
Reasonable care has been taken to ensure that this guide is accurate at the time
of printing. In the interest of progress the Company reserve the right to vary
specifications from time to time without notice.
Models
RCT250SL 250w
41001555 Iss 02

If Your Heater Does Not Work
• Check that power is available to the heater. The
LED light on the SL receiver should be illuminated
• Check that the fuse in the spur unit has not blown.
This can be done by replacing the fuse with
another suitable fuse.
• Check if the heater is paired with the SL controller
Should none of the above remedies work, then
telephone the helpline number shown in these
instructions (UK ONLY). Do not attempt to repair the
heater.
Connection to the Main
Supply
Electrical installation should be carried out by a
competent installer, preferably registered with
NICEIC in accordance with the latest edition of the
IEE Wiring Regulations, (BS.7671), and any relevant
Local Authority Bye-Laws. This heater is fitted with a 3-
core mains supply cable and must be permanently
connected to the electricity supply via a double
pole switch having 3mm gap on each pole. There
are no exceptions. A switched Fused Connection
unit to BS.1363. Part 4 is a recommended mains
supply connection accessory to ensure compliance
with safety requirements applicable to fixed-wiring
installation.
WARNING: This appliance must be earthed.
41001555 Iss 02
Overview
Please read this guide carefully and
retain for future use and maintenance.
This appliance has been designed and
manufactured to the highest
international standards. However, care
must be taken for optimal results and
safety. This appliance also meets the
requirements of EU Directive 2004/106/
EC for EMC and 2009/125/EC Directive.
Safety & Care
The appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge unless they have been
given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
Warning
• Do NOT site the appliance in a
corner.
• Do NOT touch the heater when it in
use.
• Do NOT use the appliance if
damaged.
• Do NOT leave the appliance
unattended.
• Do NOT use the heater in hazardous
areas.
• Do NOT leave the wireless receiver
on top of the heater.
Cleaning
Always isolate the heater from the mains
before cleaning. The heater should not require
any maintenance, but it is strongly advised that
it is kept clean. An occasional wipe over with
a soft cloth is all that should be necessary.
• Do NOT use metal or furniture polish on any
part of the heater.
• Do NOT touch the heater with wet hands or
in any way bring water into contact with it.
If the supply cord is damaged, the whole
heater must be.
2
N
E
INDICATOR
LIGHT
L

3
Installation
Claudgen RCT radiant ceiling tile heaters can
be installed “invisibly” in a 600 x 600 ceiling tile
system and offer each office, showroom or
store maximum interior or showroom free dis-
play space. With the integrated mounting sys-
tem the panels are easy to mount in any type
of ceiling.
The ceiling heaters warm up everything within
range of the radiant panel, just as the sun
heats the earth. This is done in a very short
amount of time. They are perfect for those are-
as that are not occupied the entire day, need
to be heated quickly and free up wall space.
Claudgen RCT radiant ceiling tile heaters only
produce radiant heat. The high intensity of the
infrared heat waves results in a comfortable
feeling in just a few minutes.
Mounting
2.1 Ceiling grid system.
• Place the heater in the required ceiling
square. The heater will fit most standard
ceiling grid systems.
NOTE! Avoid fixing vertical bars in the T-profile
where a heating panel is to be installed. The
panel fills out the whole square. It is recom-
mended that the ceiling frame is adequately
supported.
- Connect the panel.
2.2 Bracket mounting
- Measure, drill and screw the panel frame to
the ceiling.
- Hook the panel brackets to the panel frame
on the ceiling
- Connect the panel.
Note : - When mounting in gypsum board,
make sure that the panel frame is anchored in
the beam behind. During long-term high tem-
peratures the strength of the board is reduced.
41001555 Iss 02
Fig A minimum distance
A: Ceiling 80mm C: Obstacle 500mm
B: Wall 50mm D: Floor 1800mm
Panel Frame
Mains Cable
Heating panel
Panel Brackets

Consort Equipment Products Limited
Thornton Industrial Estate, Milford Haven, Pembrokeshire, SA73 2RT
Tel: [phone] Fax: [phone]
Email: [email protected] Web: www.consortepl.com
Operation hours: Mon to Thu 8.30am to 4.30pm | Fri 8.30am to 3.30pm
BS EN ISO 9001 Registered Company No FM12671
41001555 Iss 02
SL Receiver Installation
The heater is supplied with the SL wireless receiver pre-
wired. The cable length is approximately 0.9m. The
receiver should be screwed to the wall with 2x screws
and suitable wall plugs. Care should be taken when
installing the receiver. It must not be positioned
above, behind or below the heater.
The receiver has an LED plugged into the side of it.
this can be used for indication and to see the heat-
er’s current status. The LED is optional, the receiver will
operate regardless.
Technical information
Output 250w
Voltage 230v
Amps 1.09A
Max surface temp 110⁰c
Size 590x590mm
Weight 4.7Kg
CUSTOMER HELPLINE
Should you need any advice on the use of your new Consort product,
please contact our Helpline:
4
Operation
When the appliance is connected to the mains
supply, the LED indicator will light up green,
showing that the power is available to the unit.
When the heat output has been enabled by a
controller, the LED indicator light will turn red.
This heater must be used in conjunction with an
SL wireless controller. Each SL controller can
control any number of heaters providing they
are in the RF range.
Please refer to the SL user and operating instruc-
tions for full operational details.