Clenergy PV-ezRack SolarRoof Technical manual

Terracotta Tile
Code-Compliant Planning and Installation Guide V 1.0
Complying with AS/NZS1170.2-2011 AMDT 2-2016
Last Updated - May. 2022

Installation Guide / SolarRoof Terracotta Tile
1Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
Introduction
Using only PV-ezRack® parts and installer-supplied
parts as specified by the PV-ezRack® project plan.
(substitution of parts may void the warranty and
invalidate the letter of certification).
Recycling: Recycle: according to the local relative
statute.
Removal: Reverse installation process.
Ensure that there are no less than two professionals
working on panel installation.
Ensure the installation of related electrical equipment
is performed by licenced electricians.
Ensuring safe installation of all electrical aspects of
the PV array. This includes adequate earth bonding of
the PV array and PV-ezRack® SolarRoof components
as required inAS/NZS 5033: 2021.
Ensuring that the roof, its rafters/purlins, connections,
and other structural support members can support
the array under building live load conditions.
Ensuring that screws to fix interfaces have adequate
pull-out strength and shear capacities as installed.
Maintaining the waterproof integrity of the roof,
including selection of appropriate flashing.
Verifying the compatibility of the installation
considering preventing electrochemical corrosion
between dissimilar metals. This may occur between
structures and the building and between structures,
fasteners and PV modules, as detailed in AS/NZS
5033: 2021;
Verifying atmospheric corrosivity zone of installation
site by referring to AS 4312-2008 or consulting local
construction business to determine appropriate
products and installations.products and installations.
•
•
•
•
•
•
•
•
•
•
•
The Clenergy PV-ezRack® SolarRoof has been
developed as a universal PV-mounting system for
roof-mounting on pitched and flat roofs. The use of
patented aluminium base rails, Z-Module technology
and telescopic mounting technology eliminates custom
cutting and enables fast installation.
Please review this manual thoroughly before installing
PV-ezRack® SolarRoof. This manual provides:
1) Supporting documentation for building permit
applications relating to PV-ezRack® SolarRoof Universal
PV Module Mounting System.
2) Planning and installation instructions.
Complying with all applicable local or national
building codes, including any that may supersede this
manual.
Ensuring that PV-ezRack® and other products are
appropriate for the particular installation and the
installation environment.
•
•
The installer is solely responsible for:
The PV-ezRack® SolarRoof parts, when installed
in accordance with this guide, will be structurally
sound and will meet the AS/NZS1170.2:2011 Amdt
2- 2016 standard. During installation, and especially
when working on the roof, please comply with
the appropriate Occupational Health and Safety
regulations. Please also pay attention to any other
relevant State or Federal regulations. Please check
that you are using the latest version of the Installation
Manual, which you can do by contacting Clenergy
Australia via email on [e-mail] or
contacting your local distributor in Australia.
Product Warranty:
Please refer PV-ezRack® Product Warranty on our
website.
List of contents
Introduction
Planning
Tools & Components
System Overview
Installation Instructions
Certification
01
02
06
08
10
18
- Introduction -

Installation Guide / SolarRoof Terracotta Tile
2
Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
- Planning -
Planning
Determine the wind region of your installation site
Most of Australia is designated Region A which
indicates a Regional Wind Velocity of 43 m/s with
wind average recurrence of 200 years.
Some areas are designated Region B (52 m/s). Local
authorities will advise if this applies in your area.
Region C areas (64 m/s) are generally referred to as
Cyclonic and are generally limited to northern coastal
areas. Most Region C zones end 100km inland.
Region D (79 m/s) is Australia's most extreme Cyclonic
Region, located between the town of Carnarvon and
Pardoo Station in Western Australia.
•
•
•
•
Wind regions are pre-defined for the whole of Australia by the Australian Standard 1170.2. The Wind Region is an
independent factor of surrounding topography or buildings.
Region Definition:

Installation Guide / SolarRoof Terracotta Tile
3Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016 - Planning -
Determine the Terrain Category
You will need to determine the terrain category to ensure the installation meets the required standard.
Terrain Category 1 (TC1) – Very exposed open terrain with few or no obstructions and enclosed, limited-sized water
surfaces at serviceability and ultimate wind speeds in all wind regions, e.g. flat, treeless, poorly grassed plains; rivers,
canals and lakes; and enclosed bays extending less than 10km in the wind direction.
Terrain Category 1.5 (TC1.5) – Open water surfaces subjected to shoaling waves at serviceability and ultimate wind
speeds in all win regions, e.g. near-shore ocean water; larger unenclosed bays on seas and oceans; lakes; and enclosed
bays extending greater than 10km in the wind direction. The terrain height multipliers for this terrain category shall be
obtained by the linear interpolation between the values for the TC1 and TC2.
Terrain Category 2 (TC2) – Open terrain, including grassland, with well-scattered obstructions having heights generally
from 1.5m to 5m, with no more than two obstructions per hectare, e.g. farmland and cleared subdivisions with isolated
trees and uncut grass.
Terrain Category 2.5 (TC2.5) – Terrain with a few trees or isolated obstructions. This category is intermediate between
TC2 and TC3 and represents the terrain in developing outer urban areas with scattered houses, or larger acreage
developments with fewer than ten buildings per hectare. The terrain-height multipliers for this terrain category shall be
obtained by linear interpolation between the values for the TC2 and TC3.
Terrain Category 3 (TC3) – Terrain with numerous closely spaced obstructions having heights generally from 3m to 10m.
The minimum density of obstructions shall be at least the equivalent of 10 house sized obstructions per hectare, e.g.
suburban housing or light industrial estates.
Terrain Category 4 (TC4) – Terrain with numerous larger, high (10m to 30m tall) and closely-spaced constructions
buildings, such as large city centers and well-developed industrial complexes.
If your installation site is not at TC 2, 2.5 or 3, please contact Clenergy to obtain a project specific engineering certificate
to support your installation.
Verify Atmospheric Corrosivity Zone of Installation Site
Please refer to “AS 4312-2008 Atmospheric Corrosivity Zones in Australia” or consult local construction business to
verify corrosivity category of installation site to determine appropriate products and interface spacing. When standard
products are installed in high corrosivity zones, like C4/C5, interface spacing reduction factor need to be applied.
Please refer to the generic notes of Certification Letter for the details.
Note: Clenergy provided screws for Tin interfaces are suitable for up to C3 corrosive environments only.
Determine the Height of the Installation Site
This document provides sufficient information for the PV-ezRack® SolarRoof system installation up to heights of
30 meters. If your installation site is more than 30 meters high, please contact Clenergy to obtain project specific
engineering certificate to support your installation.

Installation Guide / SolarRoof Terracotta Tile
4
Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
- Planning -
Determine Roof slope
The PV-ezRack® SolarRoof system can be used for roof slopes up to 60°. Please verify that the Installation site roof
slope is between 0° and 60°.
Determine the Installation Area of Roof
Please refer to the generic notes 29, 30 and 32 of Certification Letter to determine the installation area based on
building height, length, and width. Please be aware at certain building conditions there is an Exclusion Zone for flush
installation, which is the minimum distance between PV solar panel and roof edge of "2s", where "s" is the gap between
the underside of the panel and the roof surface.
Verify Rafter Properties of Building
Please verify rafter properties of building, which could affect the interface spacing.
Timber Rafters:
Tile Roof interface spacing tables are based on a minimum depth into F7 (Pine) timber of 25mm.
Metal Rafters:
Tile Roof interface spacing tables are based on 1.9mm thick Steel Purlins G450 or equivalent. For more information,
please refer to Note 3 and 4 of the Certification Letter.
ER-I-01, ER-I-01/CS
ER-I-23
ER-I-01/EZC/ECO
ER-I-26
ER-I-51
ER-I-41/EZC/ ECO ER-I-61/EZC/ECO

Installation Guide / SolarRoof Terracotta Tile
5Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016 - Planning -
Determine the Maximum Rail Support Spacing
Please refer to the interface spacing tables in the Certification Letter appended in this document.
If a project specific Certification Letter has been provided, please refer to the support spacing in this letter.
Verify Maximum Rail End Overhang
Rail end overhang should be not over 40% of the interface spacing. For example, if the interface spacing is 1500mm,
the Rail end overhang can be up to 600mm only.
Acquire PV Modules Clamping Zone Information
It is recommended to acquire PV modules clamping zone information from PV modules manufacturer, which can help
to plan interface, and rail position and orientation.
Assembly Drawing
Please refer below for a case example of an assembly drawing of Clenergy Tile Bracket, ER-I-01, with Boral French
Terracotta Tiles:
For more information, refer to Installation Instruction on page 10.

Installation Guide / SolarRoof Terracotta Tile
6
Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
Tools and Components
Tools
Angle Grinder with
Stone Disk
5m TapeScrew Driver
(for M8 Hexagon
Socket Screw)
String &
Marker Pen
Torque Spanner Spanner
Components
ER-EC-ST
End Clamp
ER-IC-ST
Inter Clamp
C-U/30/46-G
Universal Clamp
C-U/30/46
Universal Clamp
ER-EC-DU35/40
End Clamp,
Dual 35 or 40mm
ER-EC-DU40/46
End Clamp,
Dual 40 or 46mm
ER-R-ECO
ECO-Rail
ER-SP-ECO
Splice for ECO-Rail
ER-I-01
Tile Interface
ER-I-01/CS
Tile Interface,
Carbon Steel
- Tools and Components -

Installation Guide / SolarRoof Terracotta Tile
7Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
Components
ER-I-61/EZC/ECO
Adjustable Tile Interface
with ezclick connection,
170 mm horizontal arm
ER-I-01/EZC/ECO
Tile Interface with
ezClick connection for
ECO-Rail
ER-I-51
Tile Interface, 118mm
horizontal arm
ER-I-23
Tile Interface-Landscape
ER-I-26
Tile Interface-Side
mount
ER-I-41/EZC/ECO
Adjustable Tile Interface
with ezclick connection,
120 mm horizontal arm
SCO-ECO/380
Side Channel Cover for
Cutter-Rail, length
380 mm
EZ-RE-200
Roof Hook Extender
IS-SR265/111
Isolator Shade, non-
assembly (Mill Finish)
AB-SR/IS/260
Angle Bracket
- Tools and Components -
EZ-GL-ST
Grounding Lug
EZ-GC-ST
Grounding Clip

Installation Guide / SolarRoof Terracotta Tile
8
Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
- System Overview -
System Overview
Terracotta Tile
1. End Clamp 2. Inter Clamp 3. ECO-Rail 4. Tile interface 5. Splice for ECO-Rail
Overview of PV-ezRack® SolarRoof Terracotta Tile
①
②
③
⑤
④
Improper operation may lead to deadlock of Nuts and Bolts. The steps below should be applied to stainless steel nut
and bolt assembly to reduce this risk.
General installation instructions:
(1) Apply force to fasteners in the direction of thread
(2) Apply force uniformly, to maintain the required torque
(3) Professional tools and tool belts are recommended
(4) In some cases, fasteners could be seized over time. As an option, if want to avoid galling or seizing of thread, apply
lubricant (grease or 40# engine oil) to fasteners prior to tightening.
Safe Torques
Please refer to safe torques defined in this guide as shown in the figures below. When fixing mid and end clamps, if
the torques range specified by the panel manfuacturer is different, it should be used instead. In case power tools are
required, Clenergy recommends the use of low speed only. High speed and impact drivers increase the risk of bolt
galling (deadlock) If deadlock occurs and you need to cut fasteners, ensure that there is no load on the fastener before
you cut it. Avoid damaging the anodized or galvanized surfaces.
Precautions during Stainless Steel Fastener Installation

Installation Guide / SolarRoof Terracotta Tile
9Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016 - System Overview -
All drawings and dimensions in this Installation Guide are a generic reference only. PV-ezRack® SolarRoof is to be
optimized to suit specific conditions for each project and should be documented in a construction drawing.
Major components of PV-ezRack® SolarRoof may be provided in section sizes and lengths varying from those shown
in this guide. The installation process detailed in this instruction guide remains the same regardless of changes in
component size.
If you need to do any on-site modifications or alteration of the system please provide marked up drawings/sketches
for Clenergy’s review, prior to modification, for comment and approval.
Installation Dimensions

Installation Guide / SolarRoof Terracotta Tile
10
Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
- Assess the number of modules in the vertical direction using the module height plus at least 18mm between modules
(please check the installation manual of the solar module manufacturer).
- Assess the Number of modules in the horizontal direction using the module width plus 18 mm (20 mm if using
Universal Clamps) between the modules. Note: The standard end clamp will also add 20 mm (except for dual end
clamps) on each side to the space required.
- Assess the horizontal spacing of the Roof Hooks.
- Assess the vertical spacing of the Roof Hooks = approx. 1⁄2 to 3⁄4 of module height.
- Always check the installation manual of the PV-Module you use in order to determine the allowed fixing points on
the module frame.
Installation Instructions
- Installation Instructions -

Installation Guide / SolarRoof Terracotta Tile
11 Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
Determine the positions of the Roof Hooks according to your
plans. Remove the roof tiles at the marked positions or, if
possible, simply push them up slightly.
Fix the Roof Hooks to the rafter using Clenergy provided
Buildex 14 gauge Hex Head Zips screw with minimum 25 mm
embedment as shown in the figure on the right following the
Buildex screws installation guide below:
- Use a 3/8" Hex Socket.
- Use a mains powered or cordless screw driver with a drive
speed of 3,000 RPM maximum.
- Fit the driver bit into the screw and place at the fastening
position.
- Apply consistently firm pressure (end load) to
the screwdriver until the screw is fastened.
The roof hook must not press against the roof tile.
If necessary, pack the roof hook with max pack height of 17
mm for Clenergy provided Buildex 50 mm long screw, with
max pack height of 35 mm for Clenergy provided Buildex 65
mm long screw.
If necessary, use an angle grinder to cut a recess in the tile
covering the Roof Hook at the point where the Roof Hook
extends so that the tile lies flat on the surface. If grooved tiles
are used, it will also be necessary to cut a recess in the lower
tile.
- Installation Instructions -
Incorrect Correct
Terracotta Tile Interface Installation

Installation Guide / SolarRoof Terracotta Tile
12
Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
Caution!
Do not use fitted roof hooks as a ladder, as this extreme point load could
damage the tile below.
- Installation Instructions -
ER-I-01
Variation for installation on plain tile roofs with plain tile roof cladding: A
recess must be cut into the tiles around the position of the roof hook. The
tile flashing should be used if necessary, to prevent ingress of water.
To connect several rails together, slide half of the splice into
the rear side of the rail. Fasten the first M8 Bolt using an
Allen key, and slide the next rail into the splice. Tighten the
second M8 Bolt using an Allen key. The total rail length is
recommended not to be over 30 meters considering rails
thermal expansion problem. Splice provides the electrical
connection between the 2 rails through the pressure
bolts. This eliminates the need of using 2 earthing lugs.
Recommended torque is 10 ~12 N.m.
If the rails consist of different lengths, always begin with the
shortest piece. Install the PV Rails on the Roof Hooks and
fasten loosely with M8 x 25 bolt and washers as shown in the
figure on the right. Two to three screw turns are adequate for
loose installation.
Rail Installation

Installation Guide / SolarRoof Terracotta Tile
13 Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
Adjust the vertical and horizontal positioning using the
long hole in the Roof Hook and the loosely connected
Z Module in the rail, as shown in the figure on the right.
The roof hook should not protrude over the rail after the
adjustment. The recommended torque is 16~20N·m.
- Installation Instructions -
±19mm
Deployment of Grounding Clips
1) When there is an even number of PV Module in each
row: Install the grounding clips at the positions marked X
in the figure shown. Then the number of Grounding Clips
= number of PV Module. Eg; 4 grounding clips in the
figure shown.
2) When there is an odd number of PV Module in each
row: Install grounding clips at positions marked X in
figure shown. Then the number of Grounding Clips =
number of PV Module +1. Eg; 6 grounding clips in figure
shown.
Important Notes:
- When replacing defective PV Modules, it is required
to replace the grounding clips under the defective PV
Modules.
- When removing defective PV Modules, it is required to
keep sufficient grounding clips to maintain all other PV
modules’ earthing continuity with the rail. It is required to
install grounding clips under end clamps when necessary
to achieve this.
Before installing the PV modules on horizontal rail
installations, add anti-slip protection to the lowest row
of PV modules. To do this, fasten M6 x 20 mm bolts (with
the shank downwards) to the lower mounting holes of
the PV module frame. When installing large modules (e.g.
ASE250) M8 x 20 mm bolts must be used.
PV Module Installation

Installation Guide / SolarRoof Terracotta Tile
14
Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
Place the PV Modules on to the rails and fix with End Clamps, Inter Clamps or Universal Clamps. Fasten with the Allen
key. Please use Solution 1 or 2 below according to your project.
Solution 1 (Apply Standard Clamps)
Step 1:
Place the first PV Module on the Rail according to your plan and
fix it in place using the End Clamps. Then fasten lightly with the
Allen Key as shown in the figure on the right.
- Installation Instructions -
Step 2:
Slightly lift the PV Module and slide Inter Clamps and
Grounding Clips into position. The teeth on Grounding Clip will
automatically align when the Inter Clamp is properly installed as
shown in the figure on the right.
Step 3:
loosely place the next framed PV Module into the other side of
the Inter Clamp and Grounding Clip as shown in the figure on
the right.
18mm
Important Notes:
-To fix the Grounding Clip properly, ensure the frames of PV
Modules are completely pressed against the Inter Clamps
and Grounding Clips. Visually check that Grounding Clips are
positioned properly.
-Grounding Clips are intended for SINGLE USE ONLY! Only
fasten the bolts down when the position of the PV Module
is finalized. (Only slightly tighten bolts to keep PV Modules in
place prior to the final check)

Installation Guide / SolarRoof Terracotta Tile
15 Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016 - Installation Instructions -
Step 3:
Place the first PV Module on the Rails and apply the Universal
Clamp in the End Clamp position and fasten slightly with the Allen
Key. Make sure the frame of the PV Module is fully in contact with
the Universal Clamp as shown in the figure on the right. Visually
check the Universal Clamp and PV module are properly installed.
Solution 2 (Apply Universal Clamps)
Step 1:
Twisting the head of the Universal Clamp changes the functionality
from End to Inter Clamp as shown in the figure on the right. NOTE:
Please ensure the Universal Clamp C-U/30/46 or Universal Clamp
with Grounding Clip C-U/30/46-G is positioned correctly according
to "Deployment of Grounding Clips" (P13).
Step 2:
Incline the Universal Clamp to fit the lower channel against the
lower channel of the Rail and press the Universal Clamp down
towards the other side to securely fit the upper channel against the
upper rail channel, as shown in the figure on the right.
Note:
Before installation, make sure there is enough clearance between
the screw and lower module of Universal Clamp as shown in the
figure on the right.

Installation Guide / SolarRoof Terracotta Tile
16
Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
- Installation Instructions -
20mm
Step 4:
When using as an Inter Clamp, click the Universal Clamp into the
rail channel and slightly lift the framed PV Module to ensure the
Grounding Clip is fully covered as shown in the figure on the right.
Step 5:
Loosely place the next framed PV Module into the other side of
the Universal Clamp. Ensure the Grounding Clip is fully covered
and ensure the frame of the PV Module is in close contact with
Universal Clamp as shown in the figure on the right.
Step 6:
Repeat steps above to install all PV Modules. Visually check the
Universal Clamps and PV modules are properly positioned and
then fasten all Clamps.
When you are using Universal Clamps, the gap between two
adjacent PV Modules is 20mm. The recommend torque for
Universal Clamps in the End Clamp position is 13~14N·m. The
recommend torque for Universal Clamps in the Inter Clamp
position is 16~20N·m.

Installation Guide / SolarRoof Terracotta Tile
17 Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
Apply one pre-assembled Grounding Lug per Rail. Slide the Grounding Lug into to the rail channel and fasten the bolt
M8*25 with 16~20 N·m. Strip earthing cable (the maximum size is 10 mm2 ) and insert the conductor into the provided
copper tube. Place the copper tube into the channel of Grounding Lug and tighten M6*10 with 5~6 N·m to ensure the
earthing cable is tight.
Note:
Check the electrical resistance between rail and earthing cable conductor to ensure the bonding is made.
There are three solutions for Grounding Lug installation:
- Installation Instructions -
Solution 1
Fix the Grounding Lug into the
top channel of Rail as shown in
the figure on the right.
Solution 2
Fix the Grounding Lug into the
top channel of Rail where just
under the PV Module as shown in
the figure on the right.
Solution 3
Fix the Grounding Lug at the side
channel of Rail as shown in the
figure on the right.
Slide the first PV module of the second row onto the corresponding module of the first row. Separation from the lower
PV module can be maintained for aesthetic reasons. An Inter Clamp can be used as a separator, so that the vertical and
horizontal separation of the PV modules is identical. Continue mounting the modules as described in steps on P13 to
P17 until all PV modules are installed.

Installation Guide / SolarRoof Terracotta Tile
18
Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016
- Certification -
Certification





October2020

20October2020
ClenergyAustralia
1/10DuerdinStreet
Clayton,VIC3168
CERTIFICATIONLETTER

ClenergyPV‐ezRackSolarRoofCertification–TC2,2.5,3–WindRegionA,B,C,D.InternalREF:00115.
ProjectREF:CL‐10088‐SM‐REV‐H.

MWEngineeringMelbourne,beingStructuralEngineerswithinthemeaningofAustralian
regulations,havecalculatedthemaximumspacingsforthePVez‐Rackrailsystemforthefollowing
conditions:

‐ WindLoadstoAS1170.2‐2011AMDT4‐2016
o WindTerrainCategory2,2.5and3
o Windaveragerecurrenceof200years
o WindRegionA,B,C,D
‐ Solarpanellengthupto2.2m
‐ Solarpanelwidthupto1.2m

AttachedarethetablesshowingthespacingsaccordingtoWindRegion,roofpitch,andbuilding
height.

Thevaluesshownonthesetableswillbevalidunlessanamendmentisissuedonanyofthe
followingcodes:

‐ AS/NZS1170.0‐2002AMDT4‐2016GeneralPrinciples
‐ AS/NZS1170.1‐2002AMDT4‐2016ImposedLoadings
‐ AS/NZS1170.2‐2011AMDT4‐2016WindLoadings
‐ AS/NZS1664.1‐1997AMDT1:1999AluminiumCode


Shouldyouhaveanyqueries,donothesitatetocontactus.

BestRegards,





AlbertoEscobar
Civil/StructuralEngineer
BEngMIEAustNER
BRPEC46542
RPEQ18759
[email protected]elbourne

Installation Guide / SolarRoof Terracotta Tile
19 Code-Compliant Planning and Installation Guide V 1.0 - Complying with AS/NZS1170.2-2011 AMDT 2-2016 - Certification -
STRUCTURAL DESIGN CERTIFICATION
PV-ezRackRSolarRoof tin and tile flush
interface spacing tables according to
AS/NZS 1170.2:2011 Amdt 4-2016
Within Australia
Terrain Category 2, 2.5 & 3
Client: Clenergy Australia
REF: CL-10088-SM – REV H
Date: OCT 2020
Copyright: The concepts and information contained in this document are the property
of MW Engineering Melbourne. Use or copying of this document in whole or in part
without the written permission of MW Engineering Melbourne constitutes an
infringement in copyright.
Limitation: This report has been prepared for the exclusive use of Clenergy Australia,
and is subject to and issued in connection with the provisions of the agreement between
MW Engineering Melbourne and Clenergy Australia. MW Engineering Melbourne
accepts no liability or responsibility whatsoever for any use of or reliance upon this report
by any third party other than Clenergy's clients.