Clevertronics L10 Cleverfit Pro GEN II Theatre Installation and operating instructions

1944008
V1.0
22 November 2017
Clevertronics Clevertest and Clevertest Plus
Refer to the supplementary operation guide supplied with the Product.
Zoneworks Monitored Option
L10 Cleverfit Pro with part numbers LCFPRO-TH-ZW and LCFPRO-TH-DATA are fitted with Zoneworks
communications modules (nodes).These fittings are monitored using Powerline Carrier Technology that
utilises the power cable to provide data communication to/from data routers installed on a dedicated data
trunk connected to a central Server. Zoneworks software on the server is used to monitor, coordinate
testing and collate test data from each L10 Cleverfit Pro. Zoneworks L10 Cleverfit Pro can be
commissioned by a single push of the test switch, or scanning of the supplied barcode. The LED Test
Switch indicator provides a multifunction indication of the status of the L10 Cleverfit Pro during testing and
normal operation:
State
LED Operation
Commissioned
LED on Solid (Green)
Un-commissioned
LED flashes at 0.5Hz (0.5s Green, 0.5s Yellow)
Emergency Light Test in progress
LED flashes at 3s On (Yellow) & 0.5s Off
For further information of installation of a Zoneworks XT system, please refer to the Zoneworks Users
Guide & Commissioning Guide.
DALI EM Option
L10 Cleverfit Pro with part numbers LCFPRO—TH-DALI are fitted with DALI modules (nodes) that
facilitate connection and integration to 3rd Party Lighting Control Systems. Before installing the LCFPRO-
TH-DALI please confirm that the Lighting Control System has the capability to monitor DALI Emergency
Luminaires. The LCFPRO-DALI will be addressed and configured into the control system by the Lighting
Control System Commissioning Technicians and not Clevertronics.
State
LED Operation
Commissioned/ Un-commissioned
LED on Solid (Green)
Emergency Light Test in progress
LED flashes at 1s On (Yellow) & 1s Off
“IDENTIFY COMMAND”
Fitting goes into emergency mode for 10 seconds
A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network OR a 5/6way
“structured wiring system” lead and plug facilitating the power and DALI connection. DALI connections
are marked as Da Da.
L10™ Cleverfit Pro GEN II Theatre
LED Exit
Installation & Maintenance Instruction Leaflet
Victoria (Head Office & Manufacturing)
195 Chesterville Rd
Moorabbin VIC 3189
Phone: [phone]
Fax: [phone]
New South Wales
Phone: [phone]
Fax: [phone]
Queensland
Phone: [phone]
Fax: [phone]
South Australia/Northern Territory
Phone: [phone]
Fax: [phone]
Western Australia
Phone: [phone]
Fax: [phone]
New Zealand
Phone: [phone]
Designed in Australia to comply with the requirements of
AS2293.3: 2005 and AS/NZS CISPR15: 2011
NOTE: Standard product codes with this symbol are
enabled with Clevertest Plus capability. Please refer to the
operation guide supplied with the product for details.
Models:
LCFPRO-TH-xx-zz
Testing :
Options:
Manual Test
xx = Blank
Running Man
zz=R
Zoneworks
xx = ZW
Running Man Left Arrow
zz=RL
Z/W DATA
xx = DATA
Running Man Right Arrow
zz=RR
DALI Comp.
xx = DALI
Double sided R/M
zz=DS-R
Clevertest
xx = CT
Double sided R/M Arrow
zz=DS-RAOW
(NOTE: -CT Products supplied with the Clevertest Plus Symbol are activated with
Clevertest PLUS capability. Please refer to the operation guide supplied with the product for
details).
Spare Parts:
1530030
Battery, Lithium L10 Cell, 3.3V 2500mAh
8002920
PCA: LCF-Pro #CT10142 CTP
8002710
PCA: Duris LED Strip Clvrft Pro CT10276-D1
Important:
It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant Australian and International Standards.
Installation:

1944008
V1.0
22 November 2017
The L10 Cleverfit Pro can be installed either Ceiling or Wall Mounted. The L10 Cleverfit Pro uses a “slide
connect bracket base” that is mounted and wired into position first. The main body can be installed once
the base is wired or later to avoid damage during the construction phase. Please follow the steps below
to install the L10 Cleverfit Pro Exit:
•Disengage the slide connect bracket from the exit body. Position the base in the mounting position.
•Using the bracket as a guide, mark 2 holes for mounting and one for mains access. Then install the
bracket using appropriate fixings (not supplied).
•Configure all the mounting parts and cable entry points as below (if required) and engage the body
into the slide connect bracket. Connect mains and check that the L10 Cleverfit Pro Exit is
Operational.
•If the CTP capabilities are activated, please affix the CTP Status Label to a visible surface.
Networking:
When installing the L10 Cleverfit PRO on a monitored network, (ZONEWORKS, DATA, DALI) simply
insert the relevant Smart Node PCA.
Testing:
Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24
hours. Conduct the following tests:
•For the first test, the emergency lamp must remain illuminated for at least 2 hours after disconnection
from the mains supply.
•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are
required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails
to remain illuminated for the requisite time, remedial action must be taken to repair the situation and
once completed, the unit must pass a subsequent test. For more specific information, please refer
to the current edition of the AS/NZS 2293.2 and AS/NZS 60598.2.22 Standards.
•Clevertronics recommend scheduled PCA LED Light and battery changes at 4 yearly intervals or as
determined by regular testing.
Trouble Shooting:
Below are a list of common problems and their possible causes.
Fault: The Green LED Test Switch indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault: Lamp does not illuminate in emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault: Lamp illuminates in emergency mode, but only stays on for a short period.
Check: Battery has been allowed to charge for at least 24 hours.
Battery for damage.
Rated Emergency Lumen Output in accordance with AS2293.1 (refer
to spacing tables for installation positions):
Not applicable for –TH and –SP version
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The Li-ion battery in this fitting has been selected to give excellent long life
performance in a controlled AS/NZS 60598.2.22 testing environment. Excessive battery cycling will
reduce through-life performance and may lead to premature battery failure. Battery warranty claims, as a
result of such abuse, are specifically EXCLUDED from Clevertronics warranty terms.
The luminaire is not suitable for covering with thermally insulated material.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
http://clevertronics.com.au/terms-conditions-sale-australia-nz/