Clevertronics Trade Series Manual

1942247
V1.2
12 January 2022
Instruction Sheet Template - V1.2 –Updated 06/10/2021
Testing:
Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24
hours. Conduct the following tests:
•For the first test, the emergency lamp must remain illuminated for at least 2 hours after
disconnection from the mains supply.
•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are
required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails
to remain illuminated for the requisite time, remedial action must be taken to repair the situation
and once completed, the unit must pass a subsequent test. For more specific information, please
refer to the current edition of the AS 2293.3 Standard.
Trouble Shooting:
Below are a list of common problems and their possible causes.
Fault: The Green LED Test Switch indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault: Lamp does not illuminate in emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault: Lamp illuminates in emergency mode, but only stays on for a short period.
Check: Battery has been allowed to charge for at least 24 hours.
Battery for damage.
Fault: Green LED flashes once every 5 seconds-Battery is disconnected
Check: Battery is connected.
Fault: Green LED blinks off once every 5 seconds- Charging very flat battery
Allow 20min to recover battery then recheck
Fault: Green LED flashes at 2Hz (Fast flash)- Faulty battery
Replace battery
Rated Emergency Lumen Output in accordance with AS2293.1, not applicable
for –TH (theatre) version (refer to spacing tables for installation positions):
Refer to the Technical Label for classification information.
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life
performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-
life performance and may lead to premature battery failure. Battery warranty claims, as a result of such
abuse, are specifically EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
http://clevertronics.com.au/terms-conditions-sale-australia-nz/
Trade Series Cleverfit LED Exit
Installation & Maintenance Instruction Leaflet
Victoria (Head Office & Manufacturing)
Website: www.clevertronics.com.au
Email: [e-mail]
Phone: [phone]
Fax: [phone]
New South Wales
Phone: [phone]
Fax: [phone]
Queensland
Phone: [phone]
Fax: [phone]
South Australia/Northern Territory
Phone: [phone]
Fax: [phone]
Western Australia
Phone: [phone]
Fax: [phone]
New Zealand
Phone: [phone]
Designed in Australia to comply with the
requirements of AS2293.3: 2005 and AS/NZS
CISPR15: 2017
NOTE: Standard product codes with this symbol are
enabled with Clevertest Plus capability. Please refer to
the operation guide supplied with the product for details.
Models:
ECFLED-LI
Trade Series Cleverfit LED Exit
Spare Parts:
1550195
EcoLi,3.2V 600mAh 210mm lead,noBRKT
8002900
PCA: LED Strip ECFLED-LI CT10242-D1
8002881
PCA:Driver ECFLED-LI CT10240-L6 4C40 M/NM CF 345
Important:
It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant Australian and International Standards.

1942247
V1.2
12 January 2022
Instruction Sheet Template - V1.2 –Updated 06/10/2021
Installation:
The Trade Series Cleverfit LEDExit (ECFLED-LI) can be installed either Ceiling or Wall Mounted andcan
be mounted perpendicular to a wall using the (optional) Cleverfit Cantilever Bracket. The ECFLED uses
a “slide connect bracket base” that is mounted and wired into position first. The main body can be installed
once the base is wired or later to avoid damage during the construction phase. Please follow the steps
below to install the Cleverfit Exit:
•Disengage the slide connect bracket from the exit body. Position the base in the mounting position.
•Using the bracket as a guide, mark 2 holes for mounting and one for mains access. Then install the
bracket using appropriate fixings (not supplied).
•Connect the 240VAC supply to the mounting bracket.
•Configure all the mounting parts and cable entry points as below (if required) and engage the body
into the slide connect bracket. Apply mains power and check that the Cleverfit Exit is operational.
Maintained/Non-Maintained Operating Mode:
Press the Test Button 5 times within a 4 second period to toggle operation of the fitting between
Maintained and Non-Maintained mode
Dimensions:
Cleverfit Maintenance:
Lamp Replacement:
•Use only the lamp(s) recommended on the label inside the Cleverfit.
•To replace the lamp bar, remove the self-tapping screws, disconnect the signal cable and install
the new lamp bar.
•
*Please note that the 50,000 hour LED Lamp Bar used in the Cleverfit Exit does not suffer from burn
out. Lamp replacement can be done as scheduled maintenance, at >5 year intervals. Please make a
note, in the site logbook, as to when lamps should be changed.
Battery Replacement:
•Use only the battery recommended on the label inside the Cleverfit and on this instruction.
•Remove the screw securing the fitting to the mounting bracket.
•Remove the fitting from the bracket by sliding it forward.
•The battery is located in the top of the fitting. See images.
•Remove the clip holding the battery.
•Unplug the battery from the PCA and remove it.
•Insert the new battery into the holder, route the DC cable to the PCA and plug the new battery into
the connector.
•Secure the battery using clip.
Changing Exit Legend Inserts:
The Cleverfit Exit uses Clevertronics patented “Tamper proof” Exit legend cover and comes complete
with spare legend inserts to enable straight on, left or right arrow as well as SS/DS combinations.
To change an Exit legend insert first remove the diffuser. The clear tamper proof cover is held in place
by 3 locking tabs in the top inside area of the diffuser. Use a tool to disengage and push the locking tabs
through to release the cover and remove the insert, replacing it with the desired one. When double sided
is required remove the cardboard insert from the second side when adding decal.
To re-install the clear cover, first engage the 3 small lugs on the bottom of the cover into their respective
recesses in the diffuser. Once sure the lugs are located, and then the 2 side lugs, carefully push the 3
locking tabs back in, to complete the process.