Climax Vesta Series User manual

May 20th, 2019

Table of Contents
1. INTRODUCTION ________________________________________________________________________ 1
2. APPLICATION OVERVIEW_______________________________________________________________ 2
2.1. PARTS IDENTIFICATION ___________________________________________________________ 2
2.2. THE POWER SUPPLY _____________________________________________________________ 2
3. GETTING STARTED _____________________________________________________________________ 3
3.1. EQUIPMENT REQUIRED____________________________________________________________ 3
3.2. HARDWARE INSTALLATION_________________________________________________________ 3
3.3. WI-FI SETUP ___________________________________________________________________ 4
4. LOCAL PROGRAMMING WEBPAGE ______________________________________________________ 5
4.1. CONNECTING TO WEBPAGE ________________________________________________________ 7
5. NETWORK SETTING ____________________________________________________________________ 8
5.1. WIRELESS_____________________________________________________________________ 8
6. SYSTEM SETTING ______________________________________________________________________ 9
6.1. CHANGE PASSWORD _____________________________________________________________ 9
6.3. VOIP _______________________________________________________________________ 10
6.4. AUDIO SETTING________________________________________________________________ 11
6.5. DATE &TIME__________________________________________________________________ 12
6.6. DYNAMIC DNS ________________________________________________________________ 13
6.7. FIRMWARE ___________________________________________________________________ 14
6.8. FACTORY RESET _______________________________________________________________ 15
6.9. BACKUP &RESTORE____________________________________________________________ 16
6.10. SYSTEM LOG__________________________________________________________________ 17
6.11. LOGOUT _____________________________________________________________________ 18
6.12. REBOOT _____________________________________________________________________ 18
7. HISTORY ______________________________________________________________________________ 19
7.1. EVENT LOG___________________________________________________________________ 19
8. OPERATION ___________________________________________________________________________ 20

1
1. Introduction
VCP-WIFI-R3 is an AC-powered Emergency Voice Call Point with Wi-Fi capability,
having one button that can be used to make calls when there is an emergency.
VCP-WIFI-R3 can work with routers that support Wi-Fi network, providing network
connection for making outgoing voice calls and receiving incoming calls for two-way
voice communication.

2
2. Application Overview
2.1. Parts Identification
1. ALARM Button
2. LED Indicator (Red)
- Light on: no network.
- Flashes: unable to connect to SIP.
3. LED Indicator (Green)
- Flashes: during communication.
4. Speaker
5. Microphone
6. DC Jack
- For connecting to 5V 1AAC-DC adaptor.
7. Mounting Holes
8. Triangle Mark
- The triangle mark should point straight up when the bracket is fixed on the wall.
2.2. The Power Supply
A 5V 1AAC-DC adaptor is provided for connecting VCP to power outlet.

3
3.Getting Started
3.1. Equipment required
The following equipment is required to use VCP-WIFI-R3:
A router supporting 2.4 GHz Wi-Fi network.
3.2. Hardware Installation
The VCP-WIFI-R3 can be mounted on the wall or deployed on a flat surface.
Wall Mounting
Ensure VCP-WIFI-R3 is fitted at approximately chest height where the button can be
easily accessed and operated.
1. Break through the 2 knockouts on the Wall Mounting Bracket.
2. Use the 2 holes as a template to mark off the holes’ positions. Make sure that the
triangle symbol on the bracket points straight up.
3. Drill 2 holes and screw the bracket onto the wall.
4. Connect a 5V 1A AC-DC adaptor to DC jack of VCP-WIFI-R3 and keep the cable
well-placed.
5. Fit VCP-WIFI-R3 onto the mounting bracket. Make sure the imprinted mark on
VCP-WIFI-R3 is aligned with the upper mark on the bracket.
6. Rotate VCP-WIFI-R3 clockwise to the lock position.

4
Surface Placement
The VCP-WIFI-R3 can be deployed on a flat surface without being installed at a fixed
location.
1. Clean the back of VCP-WIFI-R3 with degreaser.
2. Connect a 5V 1A AC-DC adaptor to DC jack and keep the cable well-placed to the
right or left. (Picture 1)
3. Remove the protective cover of Anti-Slip pad and apply to the back of VCP-WIFI-R3.
(Picture 2)
4. Place VCP-WIFI-R3 at desired location. (Picture 3)
Picture 1
Picture 2
Picture 3
3.3. Wi-Fi Setup
VCP-WIFI-R3 requires a working Wi-Fi router to provide network connection for
dialing/receiving voice call. VCP Wi-Fi setting can be configured using WPS protocol.
1. Make sure VCP-WIFI-R3 is under AP Mode (indicated by two beeps around 50
seconds after power on). If the VCP-WIFI-R3 has been paired with another router
before, please first manually reset the device (Please refer to page 16 Hardware
Factory Reset).
2. Press and hold the “ALARM”button on VCP-WIFI-R3 for 10 seconds, release the
button when 2 beeps are emitted.
3. VCP-WIFI-R3 will enter WPS mode for 90 seconds. During the 90 seconds period,
activate WPS function from your wireless router to pair with VCP-WIFI-R3.
4. If WPS pairing is successful, VCP-WIFI-R3 will emit 2 beeps to indicate success and
then reboot. WPS setup is complete
<NOTE>
If WPS pairing fails, VCP-WIFI-R3 will reboot automatically when the 90 seconds
period (WPS mode) expires. 50 seconds after rebooting, VCP-WIFI-R3 will emit 2
beeps and enter AP Mode.

5
4.Local Programming Webpage
After completing Wi-Fi setting, use the local programming webpage to configure
VCP-WIFI-R3 settings,
In order to locate VCP-WIFI-R3 on local network, a specific “Finder”software is provided
by Climax to locate VCP-WIFI-R3 on LAN. To install the “Finder” software”
Step 1. Insert the supplied CD-ROM into your CD-ROM drive
Step 2. Find the Finder software in the CD-ROM. Install and execute the Finder.
Step 3. Finder will automatically search for VCP-WIFI-R3 on LAN and display its
information. If available, the VCP-WIFI-R3’s LAN IP address, Firmware version
and MAC address will be displayed
If VCP-WIFI-R3 is not displayed, check VCP-WIFI-R3 AC power and make
sure its Wi-Fi is properly setup and click “Search”to update the panel
information.
Step 4. (Optional)You can choose to edit the VCP-WIFI-R3 network setting manually
by clicking on the panel column, then click “Configure Setting”

6
The LanType is default to DHCP and does not require manual input of
IP/Netmask/Gateawy/DNS setting. If you wish to configure these setting
manually, change LanType to Static.
After finish changing network setting, enter the user name (default: admin) and
password (default: cX+HsA*7F1) then click OK to confirm. The user name and
password can be changed later in the VCP-WIFI-R3’s configuration webpage
Step 5. Click the VCP-WIFI-R3 information column and click on “Open Web Page”, or
double click on the VCP-WIFI-R3 column to link to the panel configuration
webpage. Your default browser will start automatically to connect to the LAN IP
displayed in Finder.

7
4.1. Connecting to Webpage
If default login user/password is not changed, webpage login will be disabled 1
hour after power on. Please reboot the device and retry connection.
Step 1. Double click the VCP-WIFI-R3 column on Finder, or enter VCP-WIFI-R3’s LAN
IPAddress in your browser.
Step 2. Enter the login username and password
Default username: admin
Default password: cX+HsA*7F1
tep 3. You will enter change password page. Enter and repeat a new password
(username change is optional), take care that both username and password
are case sensitive. Click OK to confirm.
Step 4. Upon confirming new username and password, you will enter the Welcome
page. The webpage will prompt you to re-login with new username and
password.
The Welcome page displays VCP-WIFI-R3 info. Click on the pages and folders on the
left to access VCP-WIFI-R3’s various functions.

8
5.Network Setting
5.1. Wireless
The “Wireless”webpage display current VCP Wi-Fi setting.
Wi-Fi setting can only be changed by factory resetting VCP and using to reprogram
Wi-Fi setting. Wi-Fi setting cannot be changed on the webpage.