CoCo UCR-4285 User manual

USER’S MANUAL
version 1.1
English
UCR-4285 UNIVERSAL REMOTE CONTROL

UCR-4285 UNIVERSAL REMOTE CONTROL
Description of buttons
1. Power: On/Off/Stand-by
2. Indicator
3. Device selection
4. Menu
5. Guide
6. Two-digit number entry
7. AV channel selection
8. Enter/OK
9. Navigation/direction buttons
10. Volume higher/lower
11. Mute
12. Return to previous selection
13. Channel higher/lower
14. Teletext shortcut keys
15. Control options for video and audio recordings
and teletext functions
16. Number entry
Attention: The functions available on the UCR-
4285 only work if they were also available on the
original remote control!
2
9
8
7
5
6
4
3
1
12
10
15
14
13
11
16
1

UCR-4285 UNIVERSAL REMOTE CONTROL
2
[1] Press the latch and remove the battery cover. [2] Install 4 batteries. The poles must match the +
and - symbols on the inside of the battery
compartment. Close the cover.
Do not use rechargeable batteries!

UCR-4285 UNIVERSAL REMOTE CONTROL
CONFIGURATION USING THE CODE LIST
[3] Switch on your device manually (or with the
original remote control).
[4] Find the 5-digit code in the code list that
matches the brand of your device.
The codes shown first are the codes used most
often for a particular brand!
Go to [10] if your brand is not in the list!
The TV in the picture is only used as an
example. Follow these instructions for other AV
equipment as well!
3

UCR-4285 UNIVERSAL REMOTE CONTROL
4
3 seconds
[5] Press the device button that you want to
configure (set your television under ‘TV’, your
stereo system under ‘audio’ etc.).
The buttons are not device specific. Thus you
can configure a 2nd TV under a button you do not
use (e.g. ‘SAT’)!
[6] Press and simultaneously. Do not
release them until the indicator has flashed several
times to confirm.

UCR-4285 UNIVERSAL REMOTE CONTROL
[7] Set the code you found in [4]. [8] Point the UCR-4285 at your device. Press the
power button (device should switch off or go to
stand-by). Now check all the other functions.
If the UCR-4285 does not work or does not
work properly: Repeat steps [4-8] and use the next
code!
If none of the codes work, go to [10]!
The indicator flashes to confirm!
5

UCR-4285 UNIVERSAL REMOTE CONTROL
6
CONFIGURATION USING THE SEARCH FUNCTION
[9] Switch on your device manually (or with the
original remote control).
The TV in the picture is only used as an
example. Follow these instructions for other AV
equipment as well!
[10] Press the device button you want to configure
(set your television under the ‘TV’ button).
The buttons are not device specific. Thus you
can configure a 2nd TV under a button you do not
use (e.g. ‘SAT’)!

UCR-4285 UNIVERSAL REMOTE CONTROL
[11] Press and simultaneously. Do not
release them until the indicator has flashed several
times to confirm.
[12] Enter code ‘9 9 1’. The indicator flashes
several times to confirm.
3 seconds
7

UCR-4285 UNIVERSAL REMOTE CONTROL
8
[13] (1) Press the applicable button:
TV (CRT/CD/Plasma): Press ‘1’.
Video (DVD/VCR): Press ‘2’.
Audio (CD/Tuner/Ampl.): Press ‘3’.
Satellite/Cable/Media PC: Press ‘0’.
Press ‘Power’.
[14] (1) Point the UCR-4285 at the device and press
the direction button c. Repeat this until the device
switches off (or goes to stand-by).
(2) Immediately press ‘Enter’.
It may be necessary to repeat this up to 150
times!
Press ‘d’ if you accidentally go too far!

UCR-4285 UNIVERSAL REMOTE CONTROL
CONNECTING TO A COCO RECEIVER
[15] Activate the search mode of the receiver.
The device shown is the AC-300 with
automatic programming!
If the receiver does not have automatic
programming, use house code ‘A’ plus a number
code between 1and 14 (see ‘Remarks’ and tables
Iand II) and continue at step [17]!
[16] (1) Press the device selection button with the
light bulb.
(2) Select the button you wish to assign to the
receiver (button 1 through 0 or red, green, yellow
or blue).
(3) Press ‘CH+’. To confirm, the built-in dimmer
switches on and off two times.
9