CODELOCKS CL4510 User manual

K3 Connect User Guide
CL4510
CL5510
CL6510
Image for illustration only
Document Version: 0.2
Status: DRAFT
Author: Martin Clayton

REGULATORY COMPLIANCE
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Download the App
The K3 Connect App is available on Apple App Store and Google Play Store
1. Search the App Store (Apple iOS) or Play Store (Android) for the K3 Con-
nect App
2. Install the App on your iOS or Android device
3. After installation, open the App
4. If asked, choose whether to allow notifications (unlocking notifications,
etc)
5. Touch Create Account...
K3 Connect App
Search the Apple App
or Google Play stores
Notifications
Choose whether to al-
low notifications
Create Account
Click the Create Ac-
count button
Enter Details
Enter your details and
choose a password
Validation
Check your email for the
validation code
Success!
The K3 Connect App is
ready for use
Register
1. Enter an account name, email address and choose a password. It is rec-
ommended to leave password and backup-to-cloud enabled.
Note: You will need to enter a valid email address that you have access
to. As part of the registration process, an email containing a validation
code will be sent to that email address
2. Touch Next to continue
3. Check your email account for the validation email. Enter the validation
code contained within the email and touch Next
Page 1

Figure 6
Line 2
Line 3
Register a Lock
1. Open the K3 Connect App (if not already open)
2. Touch the +button (top-right) of the screen
3. Enter the lock DIN
CL4510: cl4510
CL5510: cl5410
CL6510: cl6510
4. Enter a name for the lock (we recommend that you choose a meaningful
name)
5. Touch the icon (top-right) of the screen
6. Enter the following sequence into your lock:
Command: #Master Code • 00 • 1 ••
Example: #12345678 • 00 • 1 ••
Note: If you have changed your Master Code, substitute the
code used in the example above with your own code.
7. The lock will now pair with your phone
8. When complete, you may be prompted to set-up the WiFi Gateway—
touch Not Now. This step will be explained later in this guide
Pairing
Enter the pairing com-
mand into your lock
Lock DIN
Use the correct DIN for
your lock
Lock Details
Enter the lock DIN and
choose a name
Lock List
For new accounts, this
list will be empty
Synchronising
The phone and lock will
now synchronise
Page 2

Basic Functions
From the lock list, you can unlock any lock within range1, synchronise, view lock
info and view logs.
1. In the lock list, swipe the lock left
2. You will see Info, Logs and Sync options
Info: View or change lock settings
Logs: View audit entries (synchronise to retrieve latest logs)
Sync: Synchronise the settings between the lock and App and retrieve
latest logs
3. To unlock the lock, simply touch the lock in the lock list—the lock icon will
turn green to confirm unlocked status
4. If asked, choose whether to allow notifications (unlocking notifications,
etc)
5. Click Create Account…
1Using the lock in conjunction with the WiFi gateway can effectively extend the
range of operation.
Unlocked
Lock status now shows
green
Unlocking
Confirmation of unlock-
ing command
Actions
Primary actions availa-
ble for the lock
Lock List
All locks paired under
the current account
Page 3

Complete
The synchronisation is
complete
In Progress
The synchronisation is in
progress
Lock List
Select Sync to begin
synchronisation
Page 4
Synchronising
Once you have made changes to the lock settings, added new Clients or need
to see the latest audit information, you need to synchronise the App with your
lock.
1. In the lock list, swipe the lock left
2. You will see Info, Logs and Sync options
Info: View or change lock settings
Logs: View audit entries (synchronise to retrieve latest logs)
Sync: Synchronise the settings between the lock and App and retrieve
latest logs
3. Touch Sync
4. Touch OK once the synchronisation is complete
Note: You will need to be within range of the lock. The effective range is
up to 10m line-of-sight. Objects and walls will affect the effective range.

Delete Sub-Master
Delete the Sub-Master
Code
Master Code
Change the Master
Code
Parameters
Modify the general lock
settings
Parameters
Modify the general lock
settings
Lock Settings
View & access lock in-
formation & settings
Sub-Master Code
Change the Sub-Master
Code
Lock Settings & Parameters
The lock settings can be opened by swiping left on the lock in the lock list and
clicking on info (see page 3).
1. The lock settings will now be available. Information displayed will include
the lock name, battery status and date/time information
2. Touch Parameters
3. The parameters screen provides access to all settings that apply to the
lock as a whole including feature selection, day lock-out, code free and
Master & Sub-Master Code changes
4. You can change any setting by touching the setting label or, where avail-
able, by sliding the switch to enabled (green) or disabled (grey)
Help: Remember to synchronise to apply the changes to the lock
Master & Sub-Master Codes
1. By default, you lock is preset with the Master Code of 12345678. It is rec-
ommended to change this default code to one of your own choice
2. Touch Change Master Code or Change Sub-Master Code to change the
respective code
3. Enter your new choice
4. Touch the to confirm
You can delete the Sub-Master Code by touching Delete Sub-Master Code on
the parameters screen.
Help: Remember to synchronise to apply the changes to the lock
Page 5

Suspend/Activate
Suspend or activate all
the Code-Free Modes
Set Code-Free Mode
Up to 10 Code-Free
Modes can be set
Code-Free Mode
View current Code-Free
status
Code-Free
Code-Free allows you to set the lock to automatically unlock at pre-determined
times. Up to 10 different Code-Free Modes can be activated.
1. From the Parameters screen (see page 5), touch Code-Free Modes
2. To set a Code-Free Mode, touch the relevant mode (0-9) and select the
days of operation and the start & end times
3. You can activate and suspend all Code-Free Modes by touching the Ac-
tions button. Suspending all Code-Free Modes will revert the lock to nor-
mal operation (normally locked)
Note: A permitted Code-Free Mode will override a non-permitted Code-
Free Mode.
Help: Remember to synchronise to apply the changes to the lock
Page 6

Figure 1
Line 2
Figure 2
Line 2
Figure 4
Line 2
Figure 5
Line 2
Figure 6
Line 2
Line 3
Page 7
General Settings
The following settings can be updated via the Parameters screen. Touch a set-
ting to change:
 Emergency Open Cancellation - when the REM 2 input has been trig-
gered, the lock will remain open for 30 minutes. This setting reverts the lock
to normal operation
 Keypad Illumination - change if and how the keypad illuminates
 Re-Lock Delay - how long the lock will remain unlocked after a successful
unlocking operation
Help: Remember to synchronise to apply the changes to the lock
Day Lock-Out
Lock out all clients on the specified days.
1. From the Parameters screen (see page 5), touch Day Lock-Out
2. Select/de-select days for access by touching the relevant days
3. Touch the to confirm (this will enable Day Lock-Out if not already ena-
bled
4. To disable Day Lock-Out, from the Parameters screen, swipe the switch
adjacent to the Day Lock-Out pattern
Note: If a client has a an Active Period that conflicts with the Day Lock-
Out, the Active Period takes priority.
Help: Remember to synchronise to apply the changes to the lock

Figure 1
Line 2
Figure 2
Line 2
Figure 4
Line 2
Page 8
NetCode
NetCode allows you to create and share a 6 digit code that will give access to
the lock for a specified period without needing a Bluetooth or WiFi1connection
to the lock.
There are four modes available: Standard (Multiple Use), Standard (Single Use),
URM (Long Term Rental) and ACC (Medium Term Rental)
1. From the Parameters screen (see page 5), touch NetCode Mode
2. Select the required mode
1WiFi connection is via the WiFi Gateway.
Help: Remember to synchronise to apply the changes to the lock
Delete a NetCode
This feature enables you to block a NetCode:
1. Enter the NetCode you wish to block
2. Confirm the NetCode
3. Touch to confirm
Help: Remember to synchronise to apply the changes to the lock

Choose Type
Select a client type
Add Client
Touch Type to choose a
client type
Figure 2
A single paired lock with
3 clients
Figure 1
Empty client list
Page 9
Clients
A client is a Code, Card, Phone or NetCode that can be used to open the lock.
1. From any screen, touch the Clients icon at the bottom of the screen
2. Initially, you will see an empty client list (figure 1) but as locks are added,
this list will populate (figure 2)
3. To add a client, touch the +button (top-right of the screen)
4. Touch Type to select a type of client
5. See the following pages for the different clients:
 Phone Page 10
 Card Page 11
 Code Page 12
 NetCode Page 13

Key
Accept or reject the key
on recipient phone
Success
Confirmation of request
Details
Enter the client details
and click Add
Choose Lock
Select the lock to add
the client to
Select Type
Select phone as the cli-
ent type
Notification
Notification on recipient
phone
Page 10
Phone Client
A phone client is a client who had both the K3 Connect App and has registered
for an account via the K3 Connect App.
1. Follow the steps on page 9
2. Click the >(next) button (top-right of the screen)
3. Touch the lock to add the client to
4. Enter the email address of the client (must have the K3 App and a K3 ac-
count)
5. Add any access periods
6. Enter a message to include with the notification
7. Touch Add to continue
8. The client will receive a notification and be able to Accept or Reject the
key
9. On accepting the key, they will be able to unlock the lock with their
phone
Help: Remember to synchronise to apply the changes to the lock

Register Card
Touch Sync client’s info
and touch card to lock
Details
Set access periods and
touch Setup lock
Choose Lock
Select the lock to add
the client to
Select Type
Select card as the client
type
Success
Smartcard now added
to lock
Page 11
Card Client
A card client is a registered MIFARE based smartcard.
1. Follow the steps on page 9
2. Click the >(next) button (top-right of the screen)
3. Touch the lock to add the client to
4. Add any access periods
5. Touch Setup lock
6. Touch Sync client’s info
7. Touch a smartcard to the lock - the lock will beep to confirm acceptance
8. Touch OK to the onscreen success message
Note: You will need to be within range of the lock. The effective range is
up to 10m line-of-sight. Objects and walls will affect the effective range.

Sync Required
You will need to sync to
apply changes
Details
Enter details and click
Add to continue
Choose Lock
Select the lock to add
the client to
Select Type
Select code as the cli-
ent type
Page 12
Code Client
A card client is a registered MIFARE based smartcard.
1. Follow the steps on page 9
2. Click the >(next) button (top-right of the screen)
3. Touch the lock to add the client to
4. Add any access periods, enter a client name and choose a code
5. Touch Add
6. A reminder to synchronise with the lock will appear—touch OK to dismiss
Help: Remember to synchronise to apply the changes to the lock

NetCode Displayed
Use Share to send the
NetCode to others
Details
Configure click Gener-
ate to continue
Choose Lock
Select the lock to create
the NetCode for
Select Type
Select NetCode as the
client type
Sharing
Send via Message or
Email
Page 13
NetCode Client
A NetCode client is code that only works from a specific date & time and for a
set duration. NetCode clients do not appear in the client list.
1. Follow the steps on page 9
2. Click the >(next) button (top-right of the screen)
3. Touch the lock to add the client to
4. Choose a start date and hour
5. Choose a duration (either days or hours). For example, for a 1 hour
NetCode, leave the Duration Day = 0 and set Duration Hour = 1
6. For type, select All Time (Multi-use) or One Time (Single-use)
7. Touch Generate to create the NetCode
8. The NetCode will be displayed - touch Close to dismiss the message or
Share to send the NetCode via email, message, etc.

User Info
Change your password
and perform backups
Settings
K3 Connect App settings
Page 14
User Info
You can change your password or configure cloud backup from the User Info
screen.
1. From any screen, touch the Settings icon at the bottom of the screen
2. On the settings screen, touch User Info
3. Touch Change Password to change your App password
4. Backup can be enabled or disabled via the switch. You can perform an
on-demand backup by touching Backup to Cloud Now

Figure 1
Line 2
Figure 2
Line 2
Figure 3
Line 2
Figure 4
Line 2
Figure 5
Line 2
Figure 6
Line 2
Line 3
Page Spare
Title
Text

Document Version: 0.2 Status: Draft
Page 1of 9
CLX500 Programming & Operating
REGULATORY COMPLIANCE
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.

Document Version: 0.2 Status: Draft
Page 2of 9
Operation
The CLX500 family of locks support standalone and App augmented operation. When being operated
independently of the App (i.e. standalone), some features are limited or not available. For the full
feature set, please use the K3 App –available from the Apple App Store or Google Play Store.
Features
Audit Trail
Records button sequence, user/smartcard information, date/time and action. Total of 4000 entries
recorded.
Flexible User Codes
Create User Codes with set active periods, one-time codes that are suspended after use.
NetCode
Remotely generate 6 digit timed codes.
Smartcard
Use MiFare compatible Smartcards for access.
Switching Output
Adaptor PCB to be provided to allow switching of 24v circuit (future product)
Timed Code Free Access
Program up to 10 different code free access profiles allowing the lock to automatically enter into
code free mode.
Transfer & Programming
Settings to be transferred via BLE (from either phone or Gateway/Cloud).
Restore to Factory Default
Restore the lock to factory default (when the Master Code is unknown).
1. Remove battery
2. Press and hold 0
3. Replace battery
4. Release 0
5. Press 0 three times
Settings
Change the Master Code
Changes the Master Code
Note: The Master Code is 8 digits in length
#Master Code •01 •New Master Code •New Master Code ••
#12345678 •01 •87654321 •87654321 ••
Result: The Master Code has been updated to 87654321
Change the Sub-Master Code
Changes the Sub-Master Code

Document Version: 0.2 Status: Draft
Page 3of 9
Note: The Sub-Master Code is 8 digits in length
#Master Code •02 •New Sub-Master Code •New Sub-Master Code ••
#123456789 •02 •44556677 •44556677 ••
Result: The Sub-Master Code has been updated to 44556677
Delete the Sub-Master Code
Deletes the Sub-Master Code
#Master Code •03 ••
#12345678 •03 ••
Result: The Sub-Master Code has been deleted
Enable & Configure Code-Free Mode
Configures the lock to allow code free passage where no code, card or phone is needed to open the lock. Up to 10 Code-
Free times can be added. Each period can be set to work on one or more specific days.
Note: Code-Free takes priority over any other setting except lock-down.
#Master Code •04 •Code-Free period <0-9> •Time Start <HHmm> •Time End <HHmm> •Week Pattern ••
#Master Code •04 •0 •0900 •1630 •1111100 ••
Result: The lock will be in Code-Free from 09:00 to 16:30 on Monday to Friday
Help: The week pattern uses a sequence of 7 numbers (MTWTFSS) that enable (1) or disable (0) Code-Free on a particular
day.
Suspend or Restore Code-Free Mode
Suspends or restores Code-Free Mode for specific or all Code-Free Mode periods.
Suspend specific Code-Free period:
#Master Code •05 •1 •Code-Free period <0-9> ••
#12345678 •05 •1 •0 ••
Result: Suspends Code-Free period 0
Restore specific Code-Free period:
#Master Code •05 •2 •Code-Free period <0-9> ••
#12345678 •05 •2 •0 ••
Suspend all Code-Free periods:
#Master Code •05 •3 ••
#12345678 •05 •3 ••
Result: Suspends all Code-Free periods
Restore all Code-Free periods:
#Master Code •05 •4 ••
#12345678 •05 •4 ••
Result: Restores all Code-Free periods
Change the Re-lock Delay
Change the time (in seconds) for the lock to remain unlocked after successful unlocking (i.e. correct code, card or
phone). The default re-lock delay is 5 seconds.
Note: The delay range is from 2 seconds to 30 seconds.
#Master Code •06 •Time <02-30> ••
#12345678 •06 •10 ••
Result: The lock will remain open for 10 seconds after successful unlocking.
Emergency Open Cancellation
By closing the normally open REM 2 contact, the lock will open for 30 minutes. The Emergency Open Cancellation reverts
the lock to normal operation after the REM 2 input has been triggered.