CODELOCKS CL1200 User manual

You are currently in: Codelocks UK > CL1200 Programming Operating Instructions
CL1200 Programming & Operating
Instructions
Print Page
CODES –The Basics
The Cabinet Lock has three code levels available:
i) Master Code
ii) Sub-Master Code
iii) User Code
The Cabinet Lock is supplied with two factory set codes:
Master Code: 11 33 55 77
User Code: 22 44
When fitted immediately change the Master Code and User Code
All Master Codes and Sub-Master Codes are 8 digits long
All User Codes are 4 digits long
The lock ‘open’ time is set at 4 seconds
FUNCTIONS
Before programming select the most appropriate function for the application.
A) Repeated Use
Important Note: This is the default function and is already pre-programmed in new locks.
This is the most common function and is used where the same code will be repeatedly used.
B) Single User (Locker Mode)
The User enters a single use code which will lock and then open the lock once only and then be
erased.
This function is used for short term, multi occupancy applications e.g. a locker in leisure centre.
The lock will now remain open until the next single use code is entered into the lock.
OPERATING INSTRUCTIONS
Note: The Cabinet Lock has a 10 button keypad and a badged bar button. The badge bar
button is hidden beneath the handle when in the locked position.
The lock has the following code levels:
Master Code can:
Open the lock
Change the Master Code

Set / Change / Delete the Sub-Master and User Code
Select between repeated use and single use codes
Restrict the locked time
Sub-Master Code can:
Open the lock
Change the Sub-Master
Set / Change / Delete the User Code
User Code can:
Open the lock
Change the User Code
A code cannot be programmed into more than one level
Lost Code procedure
Note: The procedure require the door to be open
Remove the rear-fixing bolts and and remove the lock from the door.
Remove one battery.
Press and hold the 1 button, replace the battery, the blue LED will flash twice, release the
1 button. Within three seconds press the 1 button three times. The blue LED will flash
twice and the lock will have reverted to the factory Master Code 11 33 55 77 and all
other stored settings will be erased.
Penalty Time
Entering three incorrect codes will cause the lock into shutdown for 10 seconds.
Battery Power
The Cabinet Lock should provide well in excess of 40,000 openings of 4 seconds each, from 2 x
AAA 1.5v cells.
Low Battery
When the battery power is low the Red LED will flash 3 times before the Blue LED flashes to
signal acceptance of the code. Batteries should be changed as soon as this happens.
The lock will operate for 100 times with low battery.
Battery failure override

The Cabinet Lock has been designed so an external PP3 battery can be placed against the
external contacts beneath the handle so that the lock can be opened to replace batteries should
they fail.
The procedure is as follows:
Place the contact points of the PP3 battery against the contact points at the base of the
lock, making firm maintained contact.
The positive + PP3 terminal against the + contact on the lock, and the negative –PP3
terminal against the negative contact on the lock. See image.
Enter the Master Code.
The lock will now withdraw the locking pin allowing the lock to open.
Fit new batteries by removing the upper fixing bolt and swinging the lock down over the
edge of the door. Refit the lock.
PROGRAMMING
To program –the lock must be in the open position with the badge button visible. Every
program command must commence by pressing the badge button, followed by the
Master Code, Sub-Master Code or User Code.
Master Code Commands
CHANGE THE MASTER CODE
Master Code •01 •New Master Code •New Master Code ••
Example: 11335577 •01 •12345678 •12345678 ••
Result
Master Code has been changed to 12345678

SET OR CHANGE THE USER CODE
Master Code •02 •User Code ••
Example: 11335577 •02 •9999 ••
Result
New User Code 9999 now operative
DELETE USER CODE
Master Code • 03 ••
Example: 11335577 •03 ••
Result
User Code deleted
SET OR CHANGE THE SUB-MASTER CODE
Master Code •04 •Sub-Master Code •Sub-Master Code ••
Example: 11335577 •04 •87654321 •87654321 ••
Result
Sub-Master Code 87654321 now operative
DELETE SUB-MASTER CODE
Master Code •05 •05 ••
Example: 11335577 • 05 •05 ••
RESULT
Sub-Master Code deleted
Sub-Master Code Commands
CHANGE THE SUB-MASTER CODE
Sub-Master Code •06 •New Sub-Master Code •New Sub-Master Code ••
Example: 87654321 •06 •10101010 • 10101010 ••
RESULT
Sub-Master Code has been changed to 10101010
SET OR CHANGE THE USER CODE
Sub-Master Code •07 •User Code ••
Example: 87654321 •07 • 6666 ••
RESULT
New User Code 6666 now operative
DELETE USER CODE
Sub-Maser Code •08 ••
Example: 87654321 •08 ••
RESULT
User Code deleted
User Code Commands
CHANGE THE USER CODE WHEN IN:
A) Repeated Use Mode or

B) Single Use Mode (locker mode)
A) REPEATED USE MODE (FACTORY DEFAULT)
User Code •New User Code •New User Code ••
Example: 2244 •5541 •5541 ••
RESULT
User Code now 5541
B) CHANGING FROM REPEATED USE MODE A) TO B) SINGLE USE (LOCKER
MODE)
Master Code •09 ••
Example: 11335577 •09 ••
RESULT
Lock will now operate as B) single use (locker mode)
RESTRICT THE LOCKED TIME
Master Code •10 •(number of hours lock to remain locked) ••
Example: 11335577 •10 •04 ••
RESULT
The lock will auto open after 4 hours from locking
Note:
1. Restricting the locked time only works when the lock is in B) single use (locker mode)
2. The lock can be set to auto open at the following hourly intervals 02, 04, 08, 10, 12. See above
example for programming reference.
CHANGING FROM B) SINGLE USE (LOCKER MODE) TO A) REPEATED USE
MODE
Master Code •11 ••
Example: 11335577 •11 ••
RESULT
Factory set multiple use User Code 2244 will work repeatedly until reprogrammed.