Cole Parmer Masterflex L/S 77202-50 User manual

EASY-LOAD®II
PUMP HEADS
®
®
8051203
OPERATING MANUAL
WARRANTY
Use only MASTERFLEX precision tubing with MASTERFLEX pumps to
ensure optimum performance. Use of other tubing may void
applicable warranties.
The Manufacturer warrants this product to be free from significant deviations from
published specifications. If repair or adjustment is necessary within the warranty
period, the problem will be corrected at no charge if it is not due to misuse or
abuse on your part, as determined by the Manufacturer. Repair costs outside the
warranty period, or those resulting from product misuse or abuse, may be
invoiced to you.
The warranty period for this product is noted on the Warranty Card.
PRODUCT RETURN
To limit charges and delays, contact the seller or Manufacturer for authorization
and shipping instructions before returning the product, either within or outside of
the warranty period. When returning the product, please state the reason for the
return. For your protection, pack the product carefully and insure it against
possible damage or loss. Any damages resulting from improper packaging are
your responsibility.
TECHNICAL ASSISTANCE
If you have any questions about the use of this product, contact the Manufacturer
or authorized seller.
Printed in U.S.A.
Cole-Parmer Instrument Co.
1-800-MASTERFLEX (627-8373) (U.S. and Canada only)
11 [phone] (outside U.S.)
[phone] (Local)
www.masterflex.com
Barnant Company
1-800-637-3739 (U.S. and Canada only)
11 [phone] (outside U.S.)
[phone] (Local)
www.barnant.com
A-1299-0620
Edition 06
Cole
Parmer
®
Cole-Parmer Instrument Co.
625 East Bunker Court
Vernon Hills, Illinois U.S.A. 60061-1844
1-800-MASTERFLEX (627-8373) (U.S. and Canada only)
11 [phone] (outside U.S.)
[phone] (Local)
FAX [phone] (U.S. and Canada only)
11 [phone] (Fax outside U.S.)
www.masterflex.com
e-mail: [e-mail]
Barnant Company
28W092 Commercial Ave.
Barrington, Illinois U.S.A. 60010-2392
1-800-637-3739 (U.S. and Canada only)
11 [phone] (outside U.S.)
[phone] (Local)
11 [phone] (Fax outside U.S.)
[phone] (Local Fax)
www.barnant.com
e-mail: [email protected]
Cole
Parmer
®

SPECIFICATIONS
Pump Head Number Pump Material Occlusion Shaft Length L/S®Tubing
77200-50 PPS/CRS Fixed Short L/S®13,14,16,25,17,18
77202-50 PPS/CRS Fixed Short L/S®13,14,16,25
77200-52 PPS/CRS Fixed Short L/S®15,24,35,36
77200-60 PPS/SS Fixed Short L/S®13,14,16,25,17,18
77202-60 PPS/SS Fixed Short L/S®13,14,16,25
77200-62 PPS/SS Fixed Short L/S®15,24,35,36
77200-70 PPS/CRS Fixed Long L/S®13,14,16,25,17,18
77200-72 PPS/CRS Fixed Long L/S®15,24,35,36
77200-80 PPS/SS Fixed Long L/S®13,14,16,25,17,18
77200-82 PPS/SS Fixed Long L/S®15,24,35,36
77201-60 PPS/SS Adjustable Short L/S®13,14,16,25,17,18
77201-62 PPS/SS Adjustable Short L/S®15,24,35,36
Typical Flow, Pressure and Vacuum Data
LS®Flow rate Discharge Pressure* Vacuum* Suction Lift*
Tubing @1 rpm @ 600 rpm Continuous Intermittent @ 600 rpm @ 600 rpm
mL/Rev mL/min psig (bar) psig (bar) in (mm) Hg ft (m) H20
L/S®13 0.06 36 25 (1.7) 40 (2.7) 26 (660) 29 (8.8)
L/S®14 0.22 130 25 (1.7) 40 (2.7) 26 (660) 29 (8.8)
L/S®16 0.80 480 25 (1.7) 40 (2.7) 26 (660) 29 (8.8)
L/S®25 1.7 1000 20 (1.4) 35 (2.4) 26 (660) 29 (8.8)
L/S®17 2.8 1700 15 (1.0) 20 (1.4) 20 (510) 22 (6.7)
L/S®18 3.8 2300 10 (0.7) 15 (1.0) 20 (510) 22 (6.7)
L/S®15 1.7 1000 25 (1.7) 40 (2.7) 26 (660) 29 (8.8)
L/S®24 2.8 1700 25 (1.7) 40 (2.7) 26 (660) 29 (8.8)
L/S®35 3.8 2300 20 (1.4) 35 (2.4) 26 (660) 29 (8.8)
L/S®36 4.8 2900 15 (1.0) 20 (1.4) 24 (610) 27 (8.3)
Number of rollers: 4
Maximum pump speed (rpm): 600
Nominal torque load—Running: up to 90 oz-in (6.5 kg•cm)
Housing materials: Polyphenylene sulfide (PPS), acetal, nylon
Roller materials: Cold-Rolled Steel (CRS) / Stainless Steel (SS)
Bearing materials: Cold-Rolled Steel (CRS) / Sealed Stainless Steel
Rotor materials: Stainless Steel (SS)
Operating Temperature‡:32°F to 104°F (0°C to 40°C)
Storage Temperature: –49°F to 149°F (–45°C to 65°C)
Humidity: 0% to 90% (non-condensing)
Dimensions (W x H x D):
Operating: 4inx4-3/4 in x 2-3/4 in (102 mm x 121 mm x 70 mm)
Open: 4inx5-1/2 in x 2-3/4 in (102 mm x 140 mm x 70 mm)
Weight: 1.4 lb (0.6 kg)
* As tested with NORPRENE®, PHARMED®, and TYGON®tubing.
Values will be less with silicone and C-FLEX®.
‡ Use in this temperature range for continuous duty operation with no decrease in performance or product life. Pump
heads will work outside this range with some possible reductions in performance or product life.
23
SAFETY PRECAUTIONS
NOTE: Use only MASTERFLEX precision tubing with MASTERFLEX pumps to
ensure optimum performance. Use of other tubing may void applicable
warranties.
WARNINGS: Turn drive off before removing or installing tubing.
Fingers or loose clothing could be caught in the rollers.
Stop the drive when changing tubing or its position in the
rotor mechanism (the rotor is partially exposed when the
LOADING LEVER is in the open position).
C-FLEX — Reg TM Consolidated Polymer Technologies, Inc.
NORPRENE, PHARMED, TYGON — Reg TM Norton Co.
Trademarks bearing the ® symbol in this publication
are registered in the U.S. and in other countries.
WARNING: PRODUCT USE LIMITATION
This product is not designed for, nor intended for use in, patient-connected
applications; including, but not limited to medical and dental use and,
accordingly, has not been submitted for FDA approval.
These products are covered by one
or more of the following U.S.
and corresponding foreign patents:
4,813,855

OCCLUSION ADJUSTMENT
(on 77201-60, -62 models only)
Adjust occlusion setting near top of
pump head. (Figure #4.)
“4” for nominal performance;
“5” for increased pressure/vacuum with
reduced tubing life;
“2” or “3” for longer life with less
pressure and vacuum.
NOTE: For optimum performance, turn
knob to “1” after loading. Start drive
and adjust knob until pump primes and
fluid begins to flow.
NOTE: Occlusion usually does not
need to be readjusted when changing tubing.
MULTI-CHANNEL MOUNTING
L/S EASY-LOAD II Pump Heads can be mounted in tandem (up to four),
depending on the torque capabilities of the drive. (See Figure #5.)
Special mounting hardware is required.
See REPLACEMENT PARTS AND ACCESSORIES for mounting hardware.
Figure #5. Multi-channel Mounting
CAUTION: DO NOT OVER-TIGHTEN SCREWS OR WING NUTS.
NOTE: The L/S EASY-LOAD II Pump Head can be used in any combination with
other L/S EASY-LOAD Pump Heads. The longer L/S EASY-LOAD II mounting
hardware is required (not supplied).
NOTE: The tubing on the inside L/S EASY-LOAD II Pump Head(s) can be
changed without removing the outside pump head(s) from the drive.
45
INTRODUCTION AND GENERAL DESCRIPTION
This L/S EASY-LOAD II Pump Head, when combined with a MASTERFLEX®L/S®
drive or compatible system, is designed to provide a simple, easy-to-use peristaltic
pump system. The pump head accepts several different tubing sizes for a wide
range of flow rates. The unique over-center cam design and automatic tubing
retention allow quick tubing changes and greatly reduced maintenance time.
Each pump is supplied complete with a 15 in (38-cm) length of tubing, one
mounting hardware package and this manual. A flat-bladed screwdriver or Phillips
is required to complete installation.
DRIVE COMPATIBILITY AND SETUP
The L/S EASY-LOAD II Pump Head is compatible with most MASTERFLEX®L/S®
drives with a standard tang interface. Mount the pump head using the 2 screws
provided. (See Figure #1.)
TUBE LOADING
1. Be sure the pump drive is
turned off.
2. Rotate the lever to the
left to open the pump.
3. Load the correct size
tubing. Center the tubing
between the
retainers.(Figure #2.)
4. Rotate the lever to the
right to close.
(Figure #3.)
WARNING:
Stop the drive
when changing
the tubing or its
position in the
rotor mechanism
(the rotor is partially
exposed when the
LOADING LEVER is in
the open position).
NOTE: For optimum tubing
life, keep tubing straight
where it enters and exits
the pump.
LOADING LEVER
ROTATED TO
LEFT
TUBING
CENTERED
BETWEEN
RETAINERS
Figure #1. Setup
Figure #2. Open and Load
Figure #3. Close Pump
OCCLUSION SETTING
INDICATOR WINDOW
OCCLUSION
ADJUSTMENT
KNOB
TUBING
LOADING
LEVER
Figure #4. Adjust Occlusion

REPLACEMENT PARTS AND ACCESSORIES
Rotor assembly
Pump Head Number Order No. Pump Head Number Order No.
77200-50 77200-58 77200-52 77200-59
77202-50 77200-58 77200-52 77200-59
77200-60 77200-68 77200-62 77200-69
77202-60 77200-68 77200-62 77200-69
77201-60 77200-68 77201-62 77200-69
77200-70 77200-78 77200-72 77200-79
77200-80 77200-88 77200-82 77200-89
Mounting hardware for L/S Easy-Load II Pump Heads
Set contains #8-32 screws, washers and wing nuts (in two-, three-, and four-head
hardware).
Number of heads Stainless steel
to be mounted order number
177200-01
277200-02
377200-03
477200-04
67
MAINTENANCE AND CLEANING
No lubrication is required for the L/S EASY-LOAD II Pump Head.
Use a mild detergent solution to clean the pump head.
Do not immerse nor use excessive fluid.
To disassemble pump head for cleaning — See REPLACING ROTOR instructions.
Repair is limited to the replacement of the rotor assembly. Contact dealer for
further repair information.
See REPLACEMENT PARTS AND ACCESSORIES for parts ordering information.
REPLACING ROTOR
1. Remove pump head from drive.
2. Remove rear cover of pump head.
Figure #6. Replacing Rotor
3. Remove the two screws shown in Figure #6.
4. Remove rotor assembly.
5. Install new rotor assembly and secure with two screws.
6. Reinstall rear cover.
ASSEMBLY
SCREWS