ColorKey Mover Miniwash QUAD 4 MKII User manual

Mover Miniwash QUAD 4 MKII
CKU-5037
USER MANUAL

1
Introduction
Thank you for purchasing the ColorKey Mover Miniwash QUAD 4. Please read these
instructions carefully before use. Operating this fixture according to these instructions is
important to avoid any possible damage or accidents caused by misuse.
Packing list
n 1x Mover Miniwash QUAD 4 moving head fixture
n 1x Bracket
n 1x Power cord
n User Manual
Safety
Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or when
moving or setting up the fixture.
Caution! Avoid direct eye exposure with the fixture when on.
• This fixture is for indoor use only.
• This fixture must be installed a minimum distance of 5 meters (16’4”) away from any
lighted objects.
• Do not install or operate this fixture near flammable materials.
• This device must be installed, operated, and maintained by a qualified professional.
• Do not touch the fixture with bare hands during operation as the surface temperature of
the fixture can exceed 60˚C (140˚F). Turn off power and wait 15 minutes for the fixture to
cool before attempting to touch it.
• Please check if the voltage is in accordance with the rated power before installing.
• Do not operate this fixture if the power cord has been damaged. Turn off fixture and
replace with a power cord of similar rating.

2
Display Operation
Ø MENU: Access the menu/Scroll through menu options
Ø ENTER: Open/Select the current menu option
Ø UP: Scroll through menu selection or parameter increase
Ø DOWN: Scroll through menu selection or parameters decrease

3
Menu Guide
d001
d001-d512
DMX512
nAFA
FAST
Fast auto mode
nSTS
press enter to engage (Srun) Sound Mode
nSTC
press enter to engage (Crun) Stand Alone
SLAV
press enter to engage (Son) Slave Mode
nASL
press enter to engage (SLoW) Slow Auto
PRn
PRn/rPRn
X-axis (motor) forward / backward (PAN)
TIL
TIL/rTIL
Y-axis (motor) forward / backwards (TILT)
dIS
dIS
Forward display (LED)
rdIS
Inverted display (LED)
14CH
14CH/16CH
14 channel mode / 16 channel mode
rEST
rEST
Reset
LoRd
LoRd
Factory Reset

4
DMX Values
14 Channel mode
Ch
Function
Value
1
PAN running
0-255
2
TILT running
0-255
3
Speed adjustment
0-255
4
Dimmer
0-255
5
Strobe (from slow
speed to fast speed)
0-255
6
Red dimming
0-255
7
Green dimming
0-255
8
Blue dimming
0-255
9
White dimming
0-255
10
Motor
0-15 (no function)
16-128 (fast speed Auto running & “sound
active function” off)
129-255 (slow speed Auto running &
“sound active function” on)
11
Sensitivity adjustment
(Sound active)
0-255
12
Colors
0-140 (change colors)
141-255 (sound active with changing
colors)
13
Colors changing speed
adjustment
0-250
14
No function
0-249
Reset
250-255

5
16 Channel mode
Channels
Function
Value
1
PAN running
0-255
2
Hint adjustment (PAN)
0-255
3
TILT running
0-255
4
Hint adjustment (TILT)
0-255
5
Speed adjustment
0-255
6
Dimmer
0-255
7
Strobe (from slow speed
to fast speed)
0-255
8
Red dimming
0-255
9
Green dimming
0-255
10
Blue dimming
0-255
11
White dimming
0-255
12
Motor
0-15 (no function)
16-128 (fast speed Auto running &
“sound active function” off)
129-255 (slow speed Auto running
& “sound active function” on)
13
Sensitivity adjustment
(Sound active)
0-255
14
Colors
0-140 (change colors)
141-255 (sound active with
changing colors)
15
colors changing speed
adjustment
0-250
16
No function
0-249
Reset
250-255

6
DMX Connections
Ø DMX Cable
：
The Mover Miniwash QUAD 4 can be controlled via DMX using a 3-pin XLR connection.
The standard DMX connection is XLR is: one end connects to the male plug, and the other
connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal
Noted：In order to avoid failures and interference signal transmission，we connect a
resistance120Ω （1/4W ）at the end of the DMX connecting as below:
Ø The Conversion between 3 pin and 5 pin XLR
If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable

7
Master/Slave Mode Operation
Master/Slave
Master/Slave mode allows you to connect multiple units together using one (1) unit to control
others in a chain. When a fixture is set to ‘Master Mode,’ this unit will always act as a
controlling unit until it is switched out of ‘Master Mode’. The Master unit will send out signal
via DMX to Slave units which will react in synchronization. When a fixture is set into ‘Slave
Mode’, this fixture will receive the Master signal. To avoid master signal and DMX signal
interference, do not connect DMX when using Master/Slave mode. If using a DMX run
longer than 60 meters and/or over 32 units, a signal amplifier may be required.
***Please note that Mover Miniwash QUAD 4 MKII will only work with other Mover Miniwash QUAD 4 MKII
models and not the first generation model (CKU01-5033).***
Troubleshooting
Problem
Solutions
No DMX control
u Make sure that the DMX cable is properly connected
u Make sure that the DMX controller is operational
u Check the DMX cable for tears or breaks
u Make sure that the fixture is in DMX mode
Fixture does not
respond to sound
u Make sure that the fixture is in Sound Active mode.

8
Technical Information
Power supply: AC110V-240V; 50-60HZ
Power consumption: 60W
Light source: 4 x 12W 4-in-1 LED’s (RGBW)
Life span: up to100,000 hours
Beam Angle: 25˚
Channel: 14ch/16ch
Control: Auto, Sound active, DMX512, Master/slave
Pulse frequency: 0-10HZ
Dimming: 0-100%
Pan: 540˚
Tilt: 270˚
IP rate: IP20
Notice to consumer: ColorKey offers a 2-year limited warranty. Please visit our website at
www.ColorKeyLED.com to register your product.
Please note: We recommend that you check our website periodically for updates to user
manuals and specifications at www.ColorKeyLED.com or you may contact us directly at
[email protected].