ColorKey VividPar HEX 12 User manual

VividPar HEX 12
RGBAW+UV Wash Light
CKU-2260
USER MANUAL

2
Table of Contents
INTRODUCTION .....................................................................................................................................3
SERVICE & SUPPORT...........................................................................................................................3
DISPLAY OPERATION...........................................................................................................................4
MENU GUIDE..........................................................................................................................................5
DMX VALUES..........................................................................................................................................6
6 CHANNELS MODE ..............................................................................................................................6
10 CHANNELS MODE............................................................................................................................6
IR REMOTE OVERVIEW.........................................................................................................................7
OPERATION............................................................................................................................................9
TROUBLESHOOTING ..........................................................................................................................10
...............................................................................................................................................................11
TECHNICAL INFORMATION................................................................................................................11
Please read these instructions carefully before use. Operating this fixture according
to these instructions is important to avoid any possible damage or accidents caused
by misuse.

3
Introduction
Package Contents
•VividPar HEX 12
•Power Cable
•IR Remote
•Brackets
•User Manual
Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or
when moving or setting up the fixture.
Caution! Avoid direct eye exposure with the fixture when on.
•This fixture is for indoor use only.
•Do not install or operate this fixture near flammable materials.
•This device must be installed, operated, and maintained by a qualified
professional.
•Please check if the voltage is in accordance with the rated power before
installing.
•Do not operate this fixture if the power cord has been damaged. Turn off fixture
and replace with a power cord of similar rating.
Service & Support
Your ColorKey product includes a 2-year warranty. For technical support or to register
your product, please visit https://www.colorkeyled.com/support/
You can also reach us by phone Monday thru Friday, 8:30am –5pm PST
at [phone].

4
Display Operation
Menu: Access the menu/Scroll through menu options (*Hold Menu for two
seconds exit menu and return to your chosen program)
Up: Scroll through menu selection or increase parameter
Down: Scroll through menu selection or parameters decrease
Enter: Open/Select the current menu option

5
Menu Guide
Menu Item
Values
Function
Addr
001-512
DMX Address setting
ChNd
6ch / 10ch
Channel selection mode
SLNd
NASt / SL1 /
SL2 / SL3 / SL4
Master / Slave mode 1 / Slave mode 2 / Slave
mode 3 / Slave mode 4
ShNd
CoLo
Auto
SoUn
FAdE
Performance modes –Static color select,
Auto color scroll, Color fades, Sound active
Led
On / Off
Turn LED display on or off during use
diSP
disp
Flip LED display direction
bALA
rEd, GrEE, bLuE
Manual white balance adjustment. Add or
decrease red, green, and blue values to create
desired White Balance
NAnu
rEd
GrEE
bLuE
Uhbe
Anbe
uU
Manual Mode –Create color displays by
increasing or decreasing the values for each
colors LED value parameter from 0-255.
*Example –for only Red, rEd will be 255, all
other colors 0.
teSt
Test
Auto-test –the light will automatically engage
color LEDs to test.
FhrS
0-9999
Displays lifetime fixture use hours
rF
Yes / No
IR Remote sensor on (Yes) / off (No)
teNP
Temperature
Displays internal temperature in C

6
DMX Values
6 Channels Mode
Channel
Value
Function
1
0-255
Red
2
0-255
Green
3
0-255
Blue
4
0-255
White
5
0-255
Amber
6
0-255
UV
10 Channels Mode
CH
Value
Function
1
0-255
Red
2
0-255
Green
3
0-255
Blue
4
0-255
Amber
5
0-255
White
6
0-255
UV
7
0-255
Master Dimmer
8
3-255
Strobe
9
8-255
Auto color scroll
10
008-199
Color auto scroll speed
200-255
Sound control

7
IR Remote Overview
To use the IR remote, simply point the remote at the IR receiver on the lighting
fixture. The IR receiver on the VividPar HEX 12 is located on the face with the
LED lenses.
Black Out
Black Out mode instantly turns all LED’s off.
Press the Black Out button to engage or disengage Black Out mode.
Auto
In Auto mode, the light loops through various preprogrammed colors.
To turn on Auto mode, press the Auto button, then press (+) or (-) to increase or
decrease the speed of the program.
Sound
Sound-Active mode enables the light to respond to ambient sounds in the room
using the fixture’s built-in microphone.

8
Press the Sound button to activate Sound-Active mode. Press (+) or (-) to
increase or decrease sound sensitivity based on the playback level of the music.
Strobe
In Strobe mode, the light will strobe while the button is pressed.
To turn on Strobe mode, press and hold the Strobe button, this mode can be
engaged while running other programs for added effect.When Strobe is released,
the light will continue previous operating program.
Manual Color Mixing
VividPar is capable of creating an almost unlimited number of colors by mixing the
Red, Green, Blue, Amber, UV and White LEDs.
To begin mixing colors, press the Red (R), Green (G), Blue (B), Amber (A),
UV (UV), White (W) button, then press (+) or (-) to increase or decrease the
brightness of each color. Continue with the next color until you achieve your
desired color.
Fade
In Fade Mode, the light creates smooth, gradual color transitions.
To turn on Fade mode, press the Fade button, then press (+) or (-) to increase or
decrease the speed of the program.
Color Presets
10 preset colors can be accessed from the IR Remote. Press any number between
(0) and (9) to set a color.
0 - White
1 - Red
2 - Magenta
3 - Yellow
4 - Green
5 - Blue
6 - UV
7 - Purple
8 - Pink
9 - Orange

9
Operation
Using a DMX controller:
•Use a DMX cable to connect your VividPar HEX 12 to the DMX in/out sockets on
the bottom of the light.
Using Master/Slave Mode:
The Master/Slave mode allows a group of VividPar HEX 12 units (the slaves) to
duplicate the output of another VividPar HEX 12
(the master) without a DMX controller.
1. Set each of the slaves:
◼Go to SLNd in the main menu and press enter.
◼Select SL1.
2. Set the master:
◼Go to SLNd in the main menu and press enter.
◼Select NASt.
•The master (NASt) is the unit that runs your program whether in one of the static
color modes or various Auto programs.

10
Using Slave modes (SL1,SL2,SL3,SL4) to create a light show
Using 5 or more lights for best effect, VividPar HEX 12 can help create auto-light
shows by setting lights in order from Master, SL1, SL2, SL3, SL4 and engaging Auto
Programs on the Master fixture.
1. Set each of the desired slaves SL1, SL2, SL3, SL4:
◼Go to SLNd in the main menu and press enter.
◼Select SL1.
◼Repeat steps for each slave fixture SL2, SL3, and SL4
2. Set the master:
◼Go to SLNd in the main menu and press enter.
◼Select NASt.
•For best effect, have lights connected in sequence from Master, to SL1, to SL2, to
SL3, to SL4.
•Accessing the (ShNd) programs on the Master light will now create varying displays
of synchronized light on the master and slave fixtures through (Auto) and (SoUn)
functions.
Troubleshooting
Problems
Solutions
No DMX Control
Ensure your DMX controller is sending signal and you are
using a proper and working DMX cable.
No response with IR
Remote
Engage and disengage Blackout as it may be active and
keeping the light dark
No response with IR
Remote
Ensure IR remote is enabled in Menu (rF) setting to YES

11
Technical Information
•12x12W RGBAW+UV LED Wash Light
•DMX Channel Modes: 6 / 10 channels
•Control modes: DMX 512, Master /Slave, IR Remote, Sound active, Auto
programs
•Power consumption: 160W
•Power supply: AC100-240V; 50-60Hz
•Weight: 4.4lb
•Measurements: 10.25in. x 3.14in. x 9.25in.
Please note: As we continue to work towards improving our products and your
experience as a user, we recommend that you check our website periodically for
updates to user manuals and specifications at www.ColorKeyLED.com or you may
contact us directly at in[email protected].