ColorKey WaferPar HEX 12 MK II User manual

WaferPar HEX 12 MK II
Part# CKU-2142
USER MANUAL

1
Introduction
Thank you for purchasing the ColorKey WaferPar HEX 12 MKII . Please read these
instructions carefully before use. Operating this fixture according to these instructions is
important to avoid any possible damage or accidents caused by misuse.
➢ Packing list
■ 1x WaferPar HEX 12 MK II
■ 1x Power cord
■ User Manual
Safety
Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or when
moving or setting up the fixture.
Caution! Avoid direct eye exposure with the fixture when on.
➢ This fixture is for indoor use only.
➢ This fixture must be installed a minimum distance of 5 meters (16’4”) away from any
lighted objects.
➢ Do not install or operate this fixture near flammable materials.
➢ This device must be installed, operated, and maintained by a qualified professional.
➢ Do not touch the fixture with bare hands during operation as the surface temperature of
the fixture can exceed 60˚C (140˚F). Turn off power and wait 15 minutes for the fixture to
cool before attempting to touch it.
➢ Please check if the voltage is in accordance with the rated power before installing.
➢ Do not operate this fixture if the power cord has been damaged. Turn off fixture and
replace with a power cord of similar rating.

2
Display Operation
➢ MENU: Access the menu/Scroll through menu options
➢ ENTER: Open/Select the current menu option
➢ UP: Scroll through menu selection or parameter increase
➢ DOWN: Scroll through menu selection or parameters decrease

3
Menu Guide
ITEM
MENU
SUB
MENU
FUNCTION
MODE
Addr
A.(001-512)
DMX mode
DMX MODE
CH--
10CH
10 channel mode
6CH
6 channel mode
12CH
12 channel mode
Au--
Pr.01
T.(00-99)
Macro mode 1 from slow to fast
ATUO MODE
Pr.02
T.(00-99)
Macro mode 2 from slow to fast
...
...
Pr.10
T.(00-99)
Macro mode 10 from slow to fast
Soun
Sou
So.(00-99)
Sound Active
SOUND MODE
Colo
r.(000-255)
Static Red
STATIC COLOR
g.(000-255)
Static Green
b.(000-255)
Static Blue
u.(000-255)
Static White
A.(000-255)
Static Amber
u.(000-255)
Static UV
S.(0-20)
Strobe from slow to fast
Di--
nod.0
Close dimming speed
SETUP
nod.1
Dimming speed 1
nod.2
Dimming speed 2
nod.3
Dimming speed 3
Dimming speed 4
nod.4
Show the led PCB temperature
Temp
-25~100
No Function
rSET
no
Load the default setup
REST
yes
Close dimming speed

4
DMX Values
6 channels mode
CH
VALUE
FUNCTION
1
0-255
Red
2
0-255
Green
3
0-255
Blue
4
0-255
White
5
0-255
Amber
6
0-255
UV
10 channels mode
CH
VALUE
FUNCTION
DISCRIPTION
1
0-255
0~100%
Master dimmer
2
0-255
0~100%
Dimming Red
3
0-255
0~100%
Dimming Green
4
0-255
0~100%
Dimming Blue
5
0-255
0~100%
Dimming White
6
0-255
0~100%
Dimming Amber
7
0-255
0~100%
Dimming UV
8
0-13
no function (0Hz)
Strobe from slow to fast
14-255
1~20Hz
9
0-50
no function
Macro function
51-100
Static color
101-109
Macro mode 1
110-119
Macro mode 2
...
...
190-199
Macro mode 10(Run
Macro-1 to 9)
200-255
Sound active
10
0-255
Speed for macro mode
from slow to fast
When CH9=51~100, Static
color as form-1

5
12 channels mode
CH
VALUE
FUNCTION
DISCRIPTION
1
0-255
0~100%
Master dimmer
2
0-255
0~100%
Dimming Red
3
0-255
0~100%
Dimming Green
4
0-255
0~100%
Dimming Blue
5
0-255
0~100%
Dimming White
6
0-255
0~100%
Dimming Amber
7
0-255
0~100%
Dimming UV
8
0-10
no function
Static color
11-30
Red 100%, Green0-100%,
Blue 0%
31-50
Red 100-0%, Green 100%,
Blue 0%
51-70
Red 0%, Green 100%,
Blue 0-100%
71-90
Red 0%, Green 100-0%,
Blue 100%
91-110
Red 0~100%, Green 0%,
Blue 100%
111-130
Red 100%, Green 0%,
Blue 100-0%
131-150
Red 100%, Green 0-100%,
Blue 0-100%
151-170
Red 100-0%, Green 100-
0%, Blue 100%
171-200
Red 100%, Green 100%,
Blue 100%
201-205
Color temperature 1
206-210
Color temperature 2
211-215
Color temperature 3
216-220
Color temperature 4

6
221-225
Color temperature 5
226-230
Color temperature 6
231-235
Color temperature 7
236-240
Color temperature 8
241-245
Color temperature 9
246-250
Color temperature 10
251-255
Color temperature 11
9
0-13
no function (0Hz)
Strobe mode
14-255
1~20Hz
10
0-20
no function
Macro
21-30
Auto1
31-40
Auto2
41-50
Auto3
51-60
Auto4
61-70
Auto5
71-80
Auto6
81-90
Auto7
91-100
Auto8
101-110
Auto9
111-120
Auto10
121-255
Sound (Sound active
mode)
11
0-255
Dimming speed from slow
to fast
Speed for macro
12
0-5
Depend on the operation
setup
Speed for dimming
6-55
Close dimming speed
56-105
Dimming speed 1
106-155
Dimming speed 2
156-205
Dimming speed 3
206-255
Dimming speed 4

7
DMX Connections
➢ DMX Cable
：
The WaferPar HEX 12 MK II can be controlled via DMX also with RDM function, using a
3-pin XLR connection. The standard DMX connection is XLR is: one end connects to the
male plug, and the other connects to the female. As below: pin 1: ground, pin 2: negative
signal, pin 3: positive signal
Noted：In order to avoid failures and interference signal transmission，we connect a
resistance120Ω（1/4W）at the end of the DMX connecting as below:
➢ The Conversion between 3 pin and 5 pin XLR
If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable

8
Master/Slave Mode Operation
Master/Slave
Master/Slave mode allows you to connect multiple units together using one (1) unit to control
others in a chain. When a fixture is set to ‘Master Mode,’ this unit will always act as a
controlling unit until it is switched out of ‘Master Mode’. The Master unit will send out signal
via DMX to Slave units which will react in synchronization. When a fixture is set into ‘Slave
Mode’, this fixture will receive the Master signal. To avoid master signal and DMX signal
interference, do not connect DMX when using Master/Slave mode. If using a DMX run longer
than 60 meters and/or over 32 units, a signal amplifier may be required.
Troubleshooting
Problem
Solutions
No DMX control
◆ Make sure that the DMX cable is properly connected
◆ Make sure that the DMX controller is operational
◆ Check the DMX cable for tears or breaks
◆ Make sure that the fixture is in DMX mode
Fixture does not
respond to sound
◆ Make sure that the fixture is in Sound Active mode.

9
Technical Information
Power supply: AC100-240V;50-60Hz
Light source: 12x15W 6-in-1 LEDs
Red, Green, Blue, Amber, White, UV
Power consumption: 110W
Control: Auto, Master/Slave, DMX 512 w RDM Function, Sound Active
Channel: 6/10/12 channels
Working temperature: up to 40˚C
IP rate: IP20
Notice to consumer: ColorKey offers a 2-year limited warranty. Please visit our website at
www.ColorKeyLED.com to register your product.
Please note: As we continue to work towards improving our products and your experience
as a user, we recommend that you check our website periodically for updates to user manuals
and specifications at www.ColorKeyLED.com or you may contact us directly at
[email protected].