Comelit 1622 Owner's manual

EN
TECHNICAL
MANUAL
Audio module for SB1 system
Art. 1622

2
Table of contents
Warning ............................................................................................ 2
Description....................................................................................... 3
Art. 1622 - Compatibility table............................................................3
Technical characteristics................................................................ 4
External unit installation ................................................................. 5
Connections..................................................................................... 6
Variants .....................................................................................................6
Module connection.......................................................................... 7
Ikall / Ikall Metal modules........................................................................7
Connection of button modules 33433, 33434, 33436, 33433M,
33434M, 33436M................................................................................7
Connection Art.3348B, 3348BM........................................................7
Connection Art.3360B, 3360BM........................................................7
Vandalcom modules.................................................................................8
Connection Art.3064S .......................................................................8
Connection Art.3188SB .....................................................................8
Connection Art.3070S, 3072S ...........................................................9
Modules for Single-plate external unit...................................................9
Connection Art.3063D .......................................................................9
Button programming..................................................................... 10
Special programmes ..................................................................... 11
Installation information..........................................................................13
System performance and layouts ................................................ 13
Warning
Intended use
This Comelit product was designed for use in the creation of audio and video communication systems in residential,
commercial or industrial settings and in public buildings or buildings used by the public.
Installation
All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with
careful observation of the indications provided in the Manuals / Instruction sheets supplied with those products.
Wires
Cut o the power supply before carrying out any maintenance procedures.
Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system
manual.
We advise against running the system wires through the same duct as the power cables (230V or higher).
Safe usage
To ensure Comelit products are used safely:
• carefully observe the indications provided in the Manuals / Instruction sheets
• make sure the system created using Comelit products has not been tampered with / damaged.
Maintenance
Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance
with the indications provided in the Manuals / Instruction sheets.
Any repair work must be carried out
• for the products themselves, exclusively by Comelit Group S.p.A.,
• for systems, by qualified technical personnel.
Disclaimer
Comelit Group S.p.A. does not assume any responsibility for
• any usage other than the intended use
• non-observance of the indications and warnings contained in this Manual / Instruction sheet.
Comelit Group S.p.A. nonetheless reserves the right to change the information provided in this Manual / Instruction
sheet at any time and without prior notice.

ON DIP
ON
OFF
1.
2. 3.
4. 5. 6.
3
Description
1. DIP switches for function programming and setting the
user code.
2. Switch for input/output programming.
3. Loudspeaker volume control.
4. Connector for additional module connection.
5. Jumper for managing the RC network for door lock filter
on relay contacts. (vedi variants).
6. Terminal block for connection:
SE connection for electric door lock
COM common relay contact
NC relay normally closed contact
NO relay normally open contact
GND input reference negative for DO-RTE
PR programming input
DO door open indication input
RTE local request to exit input
V- power supply negative
V+ power supply positive
LL bus line connection
Art. 1622 is an audio module which is compatible with Comelit “SB1” entry phone systems, exclusively for use in conjunction
with power supply unit Art. 1595.
It can be installed in Ikall, Ikall Metal, Vandalcom and Roma series external units and can be finished with additional modules to
meet all system requirements.
Art. 1622 - Compatibility table
Ikall Ikall Metal Vandalcom Roma
33400 33400M
3262S/0
30xx/RI
33401 33401A 33401M
3262S/1
33402 33402A 33402M
3262S/2

3.
2.1.
4
1. Loudspeaker.
2. Microphone.
3. Loudspeaker volume control.
Technical characteristics
Art. 1622
MAIN FEATURES
Audio system Yes
Audio/video system Yes
Clamps L L V+V- RTE DO PR GND SE COM NC NO
Microphone volume control Yes
Loudspeaker volume control Yes
Operating temperature (°C) -25 ÷ 55
FUNCTIONS
Key button function Yes
SETTINGS
Loudspeaker volume control Yes
Microphone volume control Yes
GENERAL DATA
Product height (mm) 55
Product width (mm) 102
Product depth (mm) 38
COMPATIBILITY
Simplebus 1 audio system Yes
ELECTRICAL SPECIFICATIONS
Door release (dry contact bridge) Yes
Door release (direct current output) Yes

2
163 cm
130 cm
1 3
Connect the module support
frame to earth.
54
LED
O
F
F
LED
O
F
F
WHITE OFF BLUE
Nameplate LED lighting
selection.
2
1
3
Alternative microphone
position (excluding 4
module entrance panel)
76 Close Open
5
External unit installation

6
Connections
Variants
230 V
10A MAX
AC-DC
12V/24V
C
M
LL
R
P
O
D
E
S
E
T
R
NC
O
+
VV
-
G
N
D
NO
1622
12/24V
AC/DC
C
M
LL
R
P
O
D
E
S
E
T
R
NC
O
+
VV
-
G
N
D
NO
On C. NO. contacts. On C. NC contacts Excluded: voltage-free contact
Variant for using the external unit relay Variant for using a safety lock
Jumper
1622
“C.NC.NO relay activation on
actuator command: 2 sec”
Set dip switches in permanent
mode as shown in figure (Dip
switch 8 ON, Dip switches
1,2,3,4,5,6,7 OFF)
Applies to Art. 1622 with R.I.
038 or greater
AUDIO ENTRY SYSTEM RISER
1622
-
+
120-230 V
1595
C
M
LL
R
P
O
D
E
S
E
T
R
NC
O
+
VV
-
G
N
D
NO
20m max. Local lock-release button.
Active input closed for DOOR OPEN signal.

7
Module connection
Ikall / Ikall Metal modules
Connection Art.3360B, 3360BM
1622
J1
J2
J1
J2
3360B
3360BM
S
G
N
DG
R
P
485
D
-
+
D
485 24
Vac
24
Vac
Connection of button modules 33433, 33434, 33436, 33433M, 33434M, 33436M
J1
J2
J1
J2
1622
Connection Art.3348B, 3348BM
J1
J2
J1
J2
2
NO
2
NC
2
C
1
NO
1
NC
1
C
K
R
AL
+
-
C
K
-
+
D D
~
+~
-
3348B
3348BM
3
3 3 6
987
AUDIO ENTRY SYSTEM RISER
1622
-
+
120-230 V
1595
C
M
LL
R
P
O
D
E
S
E
T
R
NC
O
+
VV
-
G
N
D
NO

8
Vandalcom modules
Connection Art.3064S
C
V
+
-
S
J2
J1
J1
J2
C
V
+
-
S
J2
C
V
+
-
S
J1
3064S 3064S 3064S
1622+3262S 3064S
CV3
AUDIO ENTRY SYSTEM RISER
-
+
120-230 V
1595
C
M
LL
R
P
O
D
E
S
E
T
R
NC
O
+
VV
-
G
N
D
NO
1172B1172B1172B 1172B
Use the cable supplied with Art. 3262S.
Use bulb Art. 1172B for nameplate lighting. The bulb is polarised.
Connection Art.3188SB
C
V
+
-
S
J2
J1
J1 J1
J2
C
V
+
-
S
J2
C
V
+
-
S
J2
J1
3064S 3064S 3064S
3064S
CV3
3188SB
-
AL
CK
+
~
-
~
-
AC
OUT
+
-
+
-
D
D
PGM
NC2
C1
NO1
-
RK
NC1
C2
NO2
1622+3262S
AUDIO ENTRY SYSTEM RISER
-
+
120-230 V
1595
C
M
LL
R
P
O
D
E
S
E
T
R
NC
O+
VV
-
G
N
D
NO
MAX 15
N°1 N°2 N°15
MAX 15
3064S 3064S 3064S
1172B1172B1172B 1172B
Use the cable supplied with Art. 3262S
Use bulb Art. 1172B for nameplate lighting. The bulb is polarised.
MAX 15 modules.
20m max. Local lock-release button.

9
Modules for Single-plate external unit
Connection Art.3063D
Connection Art.3070S, 3072S
3070S
X
T
-
R
XR
-
P
-
D
S
-
"S" YELLOW
"V-" BLUE
-
SD
-
3072S
12
~
12
~
P
-
R X
R
-
T
X
12
~
12
~
-
VV
+
-
VV
+
"V+" BROWN
2E7T000696
+ +
DD
J2
J1
AUDIO ENTRY SYSTEM RISER
1622
-
+
120-230 V
1595
C
M
LL
R
P
O
D
E
S
E
T
R
NC
O
+
VV
-
G
N
D
NO
Use the cable 2E7T000696 supplied with Art. 3070S and Art. 3072S.
20m max. Local lock-release button.
P
2
P
1
-
S C P
3
P
4
P
5
P
6
P
7
P
8
V
+
J2
J1 J1
J2
3063D
3063D
P
2
P
1
-
S C P
3
P
4
P
5
P
6
P
7
P
8
V
+
3063D
J1
J2
J1
N°1
N°X
CV2
AUDIO ENTRY SYSTEM RISER
1622
1172B
1172B
-
+
120-230 V
1595
C
M
LL
R
P
O
D
E
S
E
T
R
NC
O
+
VV
-
G
N
D
NO
Use the cable included in Art. 1250IV, Art. 1250IA
Use bulb Art. 1172B for nameplate lighting. The bulb is polarised.

5 64
33433
33434
33436
33433
33434
33436
-V
+V
321
Set the user code using the dip switches; see addressing table.
10
Button programming

PR
GND
7
-V
+V
PR
GND
13 2
6
1 sec
4 5
Set the dip switches for the function you wish to program, see the table below.
11
Special programmes

12
CODE DIP SWITCH ON FUNCTIONS
Door lock
223 1,2,3,4,5,7,8 Door lock command on SE in AC (default)
224 6,7,8 Door lock command on SE in enhanced AC
225 1,6,7,8 Door lock command on SE in DC
245 1,3,5,6,7,8 Door lock time: 2 sec + deactivation tone (default)
246 2,3,5,6,7,8 Door lock time: 4 sec
247 1,2,3,5,6,7,8 Door lock time: 8 sec
248 4,5,6,7,8 Door lock confirmation tone: enabled
251 1,2,4,5,6,7,8 C.NC.NO relay in parallel with SE (default)
252 3,4,5,6,7,8 Lock-release always enabled (default)
253 1,3,4,5,6,7,8 Lock-release only enabled for user called
Actuator control management
N.B. the system should not include Art. 1256 in generic actuator mode.
229 1,3,6,7,8 Enabling C.NC.NO relay on actuator control: 2 sec
230 2,3,6,7,8 Enabling C.NC.NO relay on actuator control: 4 sec
231 1,2,3,6,7,8 Enabling C.NC.NO relay on actuator control: 8 sec
228 3,6,7,8 Actuator control on serial line S: disabled (default)
227 1,2,6,7,8 Actuator control on serial line S: enabled
System functions
232 4,6,7,8 Awaiting response time: 60 sec (default)
233 1,4,6,7,8 Awaiting response time: 120 sec
234 2,4,6,7,8 Awaiting response time: 30 sec
235 1,2,4,6,7,8 Talk time: 90 sec (default)
236 3,4,6,7,8 Talk time: 180 sec
237 1,3,4,6,7,8 Self-ignition: enabled (default)
238 2,3,4,6,7,8 Self-ignition: disabled
239 1,2,3,4,6,7,8 Confirmation tone on user call: enabled (default)
240 5,6,7,8 Confirmation tone on user call: disabled
243 1,2,5,6,7,8 Reset wait time: 10 sec (default)
244 3,5,6,7,8 Reset wait time: 1 sec
208 5,7,8 Reset after lock-release in audio: enabled (default)
209 1,5,7,8 Reset after lock-release in audio: disabled
249 1,4,5,6,7,8 Call transmission: single (default)
250 2,4,5,6,7,8 Call transmission: triple
241 1,5,6,7,8 Control of internal units connected to Art. 1622: up to 70 (default)
242 2,5,6,7,8 Control of internal units connected to Art. 1622: from 71 to 100

13
Installation information
• Module Art.1622 normally function as a main external unit (timed busy signal). To set it as a secondary external unit (busy
signal active for the whole time the riser is in use), set all the selector DIP switches to ON.
• When a call is transmitted from the external unit, if a busy tone is heard instead of the ringtone, this means communication
with another external unit is in progress.
System mode
0Simplebus (default)
255 1,2,3,4,5,6,7,8 Simplebus Top
254 2,3,4,5,6,7,8 Restore default
System performance and layouts
For further information of system performance and to view installation layouts, click on the system type that best meets your
requirements:
• SB1 audio system for the creation of audio systems for residential complexes

2ª edizione 05/2018 cod. 2G40002078
www.comelitgroup.com
Via Don Arrigoni, 5 - 24020 Rovetta (BG) - Italy
CERTIFIED MANAGEMENT SYSTEMS