Comelit Simplebus1 UT1010 User manual

Passion.Technology.Design.
EN
TECHNICAL
MANUAL
Simplebus1 Ultra audio module
Art. UT1010

2
Warning
Intended use
This Comelit product has been designed and manufactured for use in the creation of audio and video communication
systems in residential, commercial, industrial and public buildings.
Installation
All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with
careful observation of the indications provided in the Manuals / Instruction sheets supplied with those products.
Wires
Disconnect the power supply before carrying out any operations on the wiring.
Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system
manual.
We advise against running the system wires through the same duct as power cables (230V or higher).
Safe usage
To ensure Comelit products are used safely:
• carefully observe the indications provided in the Manuals / Instruction sheets,
• make sure the system created using Comelit products has not been tampered with / damaged.
Maintenance
Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance
with the indications provided in the Manuals / Instruction sheets.
Any repairs must be carried out:
• for the products themselves, exclusively by Comelit Group S.p.A.,
• for the systems, by qualified technical personnel.
Disclaimer
Comelit Group S.p.A. does not assume any responsibility for
• any purpose other than the intended use,
• failure to observe the indications and warnings contained in this Manual / Instruction sheet.
Comelit Group S.p.A. reserves the right to change the information provided in this Manual / Instruction Sheet at any
time and without prior notice.

3
Table of contents
Warning ............................................................................................ 2
Description....................................................................................... 4
UT1010 ......................................................................................................4
Technical characteristics................................................................ 6
Art. UT1010 ...............................................................................................6
Installation........................................................................................ 7
Flush-mounted installation composition table....................................7
Surface-mounted installation composition table................................7
Flush-mounted installation............................................................. 8
Removing nameplates (2A) / module (2B)..............................................9
Installation with side-by-side boxes.....................................................10
Wall-mounted installation............................................................. 11
Optional .......................................................................................... 11
Removing nameplates (2A) / module (2B)............................................12
Installation with side-by-side boxes.....................................................13
Connections................................................................................... 14
UT1010 connections ..............................................................................14
Variants ...................................................................................................14
Module connection........................................................................ 15
Connection of button modules Art. UT9200.....................................15
Connection of Touch-screen module Art. UT9270 ...........................15
Connection of numeric keypad module Art. UT9279M ....................16
Programming ................................................................................. 17
Configure button type (single/dual)......................................................17
Address button modules .......................................................................17
Program call addresses.........................................................................17
Smart programming of consecutive addresses ......................... 18
Programming of specific addresses............................................ 19
Special programming via DIP-switch .......................................... 20
Special programming table...................................................................21
Twilight sensor............................................................................... 23
Button backlighting management ........................................................23
Checking twilight sensor operation .....................................................24
Adjusting the brightness of the button LEDs ......................................25
Light-me function .......................................................................... 26
Light-me function behaviour on the basis of the LED backlighting
mode........................................................................................................26
Replacing the audio module with programming restore backup27
Configuring via PC......................................................................... 28
Errors and indications................................................................... 28
System performance and layouts ................................................ 28
Addressing table............................................................................ 29

4
UT1010
Audio module for Ultra entrance panel, Simplebus 1 system. To be used in systems with power supply art. 1595 and
art. 4888C.
Easy to install and configure, thanks to the smart programming of call buttons.
Twilight sensor for automatic nameplate backlight switch-off during daytime hours.
Omnidirectional digital microphone and dual loudspeaker for high-fidelity audio.
Programmable audiovisual functions for users with disabilities.
Designed for 2 call buttons. To be finished with cap, single button or double button in professional-grade plastic
given an anti-yellowing and anti-dulling treatment or in aluminium.
Adjustment and programming can be carried out without removing the module.
Dimensions: 1 Ultra module.
ULTRA, the new and most technologically advanced entrance panel offering maximum ease of installation.
Available in flush-mounting (10 mm protrusion from the wall) or surface-mounting (just 35 mm protrusion from the
wall) versions.
Description

5
1
2
UP
12. 13. 14.
3. 4. 5. 6.
8.9.10. 11. 7.
1.
15.
16.
2.
1. Indicator LEDs
call sent (green) / system busy (red)
lock-release enabled
audio enabled
2. Speakers
3. Speaker volume control
4. S1 Button programming selector
5. S2 Special programming selector
6. Micro USB input for programming via computer
7. Twilight sensor
8. Addressing and programming Dip Switches
9. Microphone volume control
10. Programming confirmation button
11. Digital microphone
Use screwdriver supplied
12. Terminal block for connection
RTE programmable RTE (local lock-release
input) or DO input (door open indication)
GND RTE or DO input reference negative
SE door lock reference negative
NO NC COM relay contacts
V- V+ power supply
LL bus line connection
13. Ethernet terminal block, only for use in case of additional
modules with LAN
14. Connector for additional modules with LAN
15. 16. Connector for additional modules

6
Technical characteristics
Art. UT1010
GENERAL DATA
Type Modular
Product height (mm) 90
Product width (mm) 100
Product depth (mm) 35
Product weight (g) 275
Product colour Black RAL9005, Transparent, Aluminium
Material Polycarbonate, Aluminium alloy
Flush mounting Yes, with specific accessory
Surface mounting Yes, with specific accessory
COMPATIBLE SYSTEMS
Simplebus 2 audio/video with
power supply unit art. 4888C Yes
Simplebus 1 audio Yes
AUDIO SPECIFICATIONS
Microphone MEMS digital audio sensor, omnidirectional
Loudspeaker 28 mm (Ø), 8 Ohm, 1W (2)
ELECTRICAL SPECIFICATIONS
Type of power supply External power supply
Power supply voltage 33 VDC
Absorption in standby (W) 1.5
Maximum absorption (W) 3.5
HARDWARE CHARACTERISTICS
Call type Buttons
Type of buttons Mechanical
Number of buttons (no.) 2
Backlighting colour White, O
Terminals L L V+ V- COM NC NO SE GND RTE TX- TX+ RX- RX+
Number of inputs (no.) 1
Number of outputs (no.) 2
Communication port Micro-USB
Twilight sensor Ye s
SETTINGS
Loudspeaker volume Yes
Mic volume Yes
Backlighting brightness Yes
ENVIRONMENTAL AND CONFORMITY
SPECIFICATIONS
Operating temperature (°C) -25 to 55
Operating humidity (max RH - %) 25 to 95
Environmental class III
Conformity and Certifications RoHS II - 2011/65/EU (EN 50581:2012), EMC 2014/30/EU (EN61000-6-
1:2007, EN 61000-6-3:2007+A1:2011)
MAIN FUNCTIONS
Lock-release Yes
Number of auxiliary relays (no.) 1
Input for local key button Yes
Input for door open signal Yes
System status visual indications Yes
System status audio indications Yes
System status voice synthesis Yes

7
Installation
A = Flush-mounted box
B = Rain shield
C = Flush-mounted module holder
with finishing frame
Flush-mounted box
3110/1 3110/2 3110/3 3110/4
Rain shield
UT9181 UT9182 UT9183 UT9186 UT9189 UT9184 UT9188
Module holder/ finishing frame
UT9161 UT9162 UT9163 UT9164
A = Rain shield
B = Surface-mounted housing
with frame
Rain shield UT9191 UT9192 UT9193 UT9196 UT9199 UT9194 UT9198
Housing/frame UT9171 UT9172 UT9173 UT9176 UT9179 UT9174 UT9178
Optional
The entrance panel is available in flush-mounted or surface-mounted variants:
Flush-mounted installation composition table
Surface-mounted installation composition table

8
2
1
2
UP
53 4
165 cm
130 cm
1
Flush-mounted installation
Optional
BLACK
RED
Optional

9
6
1
A
B
C
C
2
+ Art. UT9110
MAX 0,2 mm
MAX 0,2 mm
9
1
2
10 12
2
1
11
CLACK!
CLACK!
1
2
3CLACK!
8
CLACK!
CLACK!
CLACK!
1
2
3
7
1
2
3
1
2
3
1
2A
1
3
2
4
2B
Removing nameplates (2A) / module (2B)
CLOSE
The button has a nameplate which can be written on (A);
alternatively, an adhesive label can be applied (B).
The total thickness of the nameplate + adhesive label
must not exceed 0.2 mm.
You can visit the website pro.comelitgroup.com to download
the PDF to print the entrance panel name cards, using the
adhesive pre-cut sheets (C) available in our catalogue (Art.
UT9110)

10
Installation with side-by-side boxes
Before installing the boxes in the wall, fit the spacers.

11
165 cm
130 cm
2
UP
53 4
UP
1
2
3
1
Wall-mounted installation
Optional
Optional
BLACK
RED

12
6
1
A
B
C
C
2
+ Art. UT9110
MAX 0,2 mm
MAX 0,2 mm
9
1
2
10
2
1
11 12
CLACK!
CLACK!
1
2
CLACK!
3
8
CLACK!
CLACK!
1
2
CLACK!
3
7
1
2
3
1
2
1
3
2A
1
3
2
4
2B
Removing nameplates (2A) / module (2B)
The button has a nameplate which can be written on (A);
alternatively, an adhesive label can be applied (B).
The total thickness of the nameplate + adhesive label
must not exceed 0.2 mm.
You can visit the website pro.comelitgroup.com to download
the PDF to print the entrance panel name cards, using the
adhesive pre-cut sheets (C) available in our catalogue (Art.
UT9110)
CLOSE

13
Installation with side-by-side boxes

14
AUDIO ENTRY SYSTEM RISER
E
T
R
GND
SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
UT1010
ON
1 2 3 4 6 75 8
E
T
R
GND SE NO NC
C
O
M
LL
+
VV
-
12/24V
AC/DC
120-230 V
-
+
1595
E
T
R
GND SE NO NC
C
O
M
LL
+
VV
-
230 V
10A MAX
AC-DC
12V/24V
120-230 V
-
+
1595
UT1010
UT1010
Connections
UT1010 connections
Max 20 m. Local door-opener button.
“C.NC.NO relay activation on actuator command:
2 sec”
fSet DIP switch 8 to ON permanently (as shown in
the figure)
Max 20 m. Local door-opener button.
Variants
Variant for using the outdoor entrance panel relay Variant for using a safety door lock

15
UP
BLACK
RED
UT9200
AUDIO ENTRY SYSTEM RISER
E
T
R
GND SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
UT1010
AUDIO ENTRY SYSTEM RISER
E
T
R
GND
SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
UT9270
UT1010
Module connection
Connection of button modules Art. UT9200
Connection of Touch-screen module Art. UT9270
Max 20 m. Local door-opener button.
Max 20 m. Local door-opener button.

16
AUDIO ENTRY SYSTEM RISER
E
T
R
GND
SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
UT9279M
UT1010
Connection of numeric keypad module Art. UT9279M
Max 20 m. Local door-opener button.

17
65
default
65
ON
OFF
1
ON
2 3 4 65
8765 8765
default
ON
OFF
1
ON
2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
1
2
4
3
5
Programming
For correct programming, follow the instructions below in order
I. Configure button type
II. Address button modules
III. Program call addresses
code
DIP ON
1112 3.4 23 1,2,3,5
2213 1,3,4 24 4.5
31.2 14 2,3,4 25 1,4,5
4315 1,2,3,4 26 2,4,5
51.3 16 527 1,2,4,5
62.3 17 1.5 28 3,4,5
71,2,3 18 2.5 29 1,3,4,5
8419 1,2,5 30 2,3,4,5
91.4 20 3.5 31 1,2,3,4,5
10 2.4 21 1,3,5
11 1,2,4 22 2,3,5
TAB. A
Configure button type (single/dual)
DIP 6: configuring button type:
Single button (DIP6 ON).
Dual button (DIP6 OFF, default).
I
Address button modules
DIP 1-5: addressing call button module (see TAB. A)
Addressing call button modules means that, in the event they are replaced, it is not necessary to reprogram the
button addresses. All you need to do is assign the same address as before to the new module.
II
Program call addresses
There are 2 programming methods:
• Smart programming of consecutive addresses: allows quick programming of buttons with consecutive addresses
(e.g.: 1, 2, 3, 4)
• Programming of specific addresses: allows programming of specific addresses (e.g.: 25, 37, 70, 58)
III
DIP 6: configuring button type:
Single button (DIP6 ON).
Dual button (DIP6 OFF, default).

18
LL
S1 S2
S1 S2
2
7
3
ON
1 2 3 4 6 75 8
=1
= 3
+1 = 4 +1
= 5
+1
= 2
+1
1
4 5
6
8
Smart programming of consecutive addresses
Make sure the button configuration (single/dual) is correct before proceeding with programming (see
“Configure button type (single/dual)”)
When programming is
complete, make sure the
button configuration is
correct (single/dual), see
“Configure button type
(single/dual)”)
Take note of the DIP-switch
settings
example:
code 1
Set the address of the
apartment you wish
to call (for example:1)
using the DIP-
switches
(see “Addressing
table” )
Press the button you
want to associate with
the call address set
using the DIP-switches
Press the following
buttons to assign
consecutive
addresses.
Reset the configuration of the
DIP-switches

19
LL
S1 S2
S1 S2
2
7
3
1 2 3 4 6 75 8
=25
70 58
37
ON
1 2 3 4 6 75 8
ON
1 2 3 4 6 75 8
ON
1 2 3 4 6 75 8
1
4 5
6
8
Programming of specific addresses
Make sure the button configuration (single/dual) is correct before proceeding with programming (see
“Configure button type (single/dual)”)
When programming is
complete, make sure the
button configuration is
correct (single/dual), see
“Configure button type
(single/dual)”)
Take note of the DIP-switch
settings
example:
code 25
example: code 37 example: code 70 example: code 58
Set the address of the
apartment you wish to
call (for example:25)
using the DIP-
switches
(see “Addressing
table” )
Press the button you
want to associate with
the call address set
using the DIP-switches
Repeat steps 4 and
5 to assign a specific
address to each button
Reset the configuration of the
DIP-switches

20
LL
S1 S2
2 3
2
1
1
4
S1 S2
5 6
Special programming via DIP-switch
Take note of the DIP-switch
settings
1. Set the dip switches in accordance with the function you
wish to program (see table).
2. Press the confirm button.
Reset the configuration of the
DIP-switches
When programming is
complete, make sure the
button configuration is
correct (single/dual), see
“Configure button type
(single/dual)”)