Comelit HUB32LCD User manual

EN
USER MANUAL
Quick-start user manual for wireless intruder alarm
control panel HUB32LCD Passion.Technology.Design.

2
Index
Index ................................................................................................. 2
Available documentation ................................................................ 3
Introduction...................................................................................... 3
The front panel................................................................................. 4
Viewing the system status.............................................................. 4
Accessing the menu........................................................................ 5
Arming the alarm system................................................................ 5
Disarming the alarm system........................................................... 5
Forced arming.................................................................................. 5
Custom area arming........................................................................ 6
Show open zones / faults ............................................................... 6
Show bypassed zones .................................................................... 6
System in alarm ............................................................................... 6
Silencing an alarm / Alarm Memory .............................................. 7
Generating a fire / medical / panic alarm...................................... 7
Walk test........................................................................................... 7
View / edit zone status.................................................................... 8
Using the radio control ................................................................... 9
Adding new user codes .................................................................. 9
Consult event log........................................................................... 10

3
Introduction
Thank you for choosing a Comelit Secur Hub wireless intruder alarm system. It is designed to oer the utmost flexibility and ease of use. Cutting-edge connectivity,
advanced video surveillance functions and elegant design make it the perfect choice to keep your family and your property safe.
The system can be armed in various ways, depending on the routines and requirements of its users. All sensors oer constant and reliable monitoring of your
residence, thanks to two-way communication which maximises information redundancy. Audible, visual or silent notifications of any violations or tampering can be
provided on site or remotely through a wide range of signalling channels: e-mail, voice calls, SMS or app notifications. The control panel can also be connected to
a alarm receiving centre (ARC) by means of specific protocols.
Real-time management, supervision and video verification are available via the Comelit app for Android and iOS. Live viewing - via the app - of the IP cameras
connected to the system is instant and allows you to check the actual cause of any alarms, or to check whether everything is OK at home. A short video can also
be recorded and sent to the app when an alarm occurs on the system, including the few seconds prior to the intruder event.
The control panel has a built-in microphone and speaker which allow users to call rooms from a remote telephone and start a hands-free two-way audio
conversation. A GSM or 3G module is required for this function.
The built-in speaker can be used to play customisable messages relating to most control panel procedures.
This manual will guide you through basic control panel operation using the keypad and remote control.
Please read this document carefully before operating the system. Refer to the full operating manual HUB32LCD for a complete guide to all procedures and user
menu features.
Available documentation
• Quick installation manual: This document contains all the information required for product installation and initial startup.
• HUB32LCD installation and programming manual: this document contains all the information required to program a Secur HUB system via keypad.
• Secur HUB Manager programming manual: this document contains all the information required to program a Secur HUB system using Secur HUB Manager
software.
• HUB32LCD user manual: this document contains all the information required by the end user of a Secur HUB system.
• The documentation is available online, at mycomelit.com
The SECUR HUB system comes with a series of technical manuals containing detailed information for the installation, programming and use of the control panel
and the available accessories.

4
The front panel
1
2
34
56 7
1. 16 x 2-character LCD.
2. LED indicators: green, orange, red.
3. Alphanumeric keypad.
4. Arming/disarming buttons.
5. Back/Cancel/Delete button.
6. Enter/Confirm button.
7. Navigation keypad / menu button.
• Green LED: indicates the system is armed
(lit steadily) or in
“not ready to arm” condition (flashing). The LED is o if the
system is ready for arming.
• Orange LED: indicates a fault (lit steadily) or isolated /
bypassed zones (flashing).
• Red LED: indicates an alarm / tampering in progress (lit
steadily) or an alarm in the memory (flashing).
Viewing the system status
System ready to arm - Single area System armed - Single area System not ready to arm - Single area
Flashing
System ready to arm - 4 areas System armed - 4 areas System not ready to arm - 4 areas
Flashing for areas not ready to arm
Exit delay - single area Entry delay - single area Entry and exit delay - 4 areas
Countdown
The control panel has a display that can show the system status. The pictures below illustrate the various messages based on the system status.
The messages on the display change depending on whether the system is used to monitor a single area or several areas. In the latter case (multi-area), the bottom
line of the display is divided into four to display the status of each individual area (only existing areas are actually shown). See below for the dierences between
single area and multi-area displays:
Countdown Countdown
System part armed - Single area System part armed - 4 areas

5
Accessing the menu
Enter user code (default: 111111)
Arming the alarm system
Enter user code (default: 111111)
Forced arming
If open zones or faults are detected during the system arming procedure, the user will be asked to choose whether to proceed with a forced arming command or
to abandon the procedure. If “Enter” is pressed the system will proceed with forced arming and will arm according to the “Forced arm options”. You can also scroll
through the list of conditions to force using the down arrow.
The user menu is accessed by entering the user code followed by the down arrow. A guide to all user menu options is available online. See the chapter “Available
documentation”.
The system can be armed in various ways: total arm, part arm 1 and part arm 2.
Total arming is used when you are leaving the premises. In this arming condition, the whole system is armed and all detectors trigger an alarm if violated according
to their configuration. Note that some devices, such as flooding and smoke detectors, trigger an alarm regardless of the arming status.
Part arms 1 and 2 allow the user to arm parts of the system while they are still occupying other parts. For example, all window detectors can be armed, leaving the
indoor motion detectors disarmed. This allows the user to move freely around the rooms while the whole perimeter of the property is monitored. There are three
arming buttons on the keypad assigned by default to these arming modes.
A delay can be set on some detectors, to allow the user to leave the premises following an arming command or to enter the premises and disarm the system. Ask
your installer for more information.
Disarming the alarm system
The alarm system can be disarmed using the keypad, by entering the user code and pressing the open padlock icon in the bottom right-hand corner. An audible
confirmation tone and the text “Disarmed” confirm that disarming has taken place.
Flashing

6
Show bypassed zones
You can check the list of bypassed zones by pressing Enter. You can scroll through the list using the “Down arrow”.
System in alarm
In alarm condition, the type of alarm and the zone involved are shown. The red LED switches on.
If there is more than one alarm, you can scroll through them using the “Down arrow” (an arrow will appear on the right-hand side of the display to show that more
than one alarm is present).
Show open zones / faults
If there are open zones, the system will show “not ready to arm” and the green LED will flash. The “X” button will show the list of open zones, which will scroll
automatically (2 seconds for each zone). You can scroll through the list manually using the “Down arrow”.
2 Sec
Custom area arming
This procedure is used to configure a custom arming program in which the user can quickly select the arming status for each area.
• Access custom arming set with [CODE] + [ENTER].
• Using buttons 1, 2, 3, 4 the user can set the desired arming status for each area (if present). An asterisk beside the arming status indicates that the setting has
been changed (but the areas are not in that condition yet).
• The total arming button will then confirm the command.
Enter user code (default: 111111)
Flashing
Flashing

7
Walk test
The walk test is used to check zone functions. When the system is in walk test mode, the installer should activate all zones in sequence and the system will emit
an audible signal after every activation. The display will show how many zones have been tested and the total number to test. A confirmation message will be
displayed when all the zones have been tested. The zones to be tested are selected in the installation menu. The zones with a poor RF signal are listed as missing
zones with the message “LOW!”.
All zones
activated
Zone
activation
Silencing an alarm / Alarm Memory
After an alarm is triggered, the control panel begins to send the intruder event alerts to the contacts in the phonebook programmed by the installer. The siren
begins to sound, the red LED on the control panel is lit steadily and the alarm alert is displayed. If the zone is reset, the control panel will show the message
“System in alarm” (flashing). Enter a valid user code and disarm the system to silence all the indications.
After disarming, the alarm memory will be shown once and then it will be reset. If the system is not disarmed after an alarm, the system will indicate an alarm
memory condition by means of the red LED flashing and the alert “System in alarm” (flashing). The user can scroll through the alarm memory using the down arrow.
Reset
zone
Flashing Flashing
Generating a fire / medical / panic alarm
Specific button combinations can be used to activate emergency alarms. To program the recipients of notifications relating to these alarms, please contact your
installer. To activate the alarms, press the button combinations for approximately 2 seconds.
FIRE MEDICAL PANIC

8
View / edit zone status
This menu can be used to select which zones will be excluded in the next arming procedure. Exclusion prevents the violation of these zones from triggering an
alarm. The same menu can be used to isolate a zone (this prevents that zone from generating any messages, including the tampering message).
Please bear in mind that excluded zones are automatically re-included when the system is disarmed.

9
Using the radio control
5
2
4
1
3
1. Button 1
2. Button 2
3. Button 3
4. Button 4
5. 3-Colour LED
The remote control has 4 buttons. All the buttons can be configured using the programming software on the control panel. By default button 1 is assigned to the
“total arming” command, button 2 to “disarm”, button 3 to “part arm 1” and button 4 to “part arm 2”.
Keypad lock/unlock:
Press and hold buttons 2 and 4 until the orange LED starts flashing rapidly. While it is flashing, press button 4 once.
»The red LED will confirm locking.
»The green LED will confirm unlocking.
LED indications:
• Button pressed: Short red flash.
• Command executed: two green flashes.
• Command rejected: two red flashes.
• Arming: Slow red flash.
• Disarming: Slow green flash.
• Low battery: Yellow flash preceding any other signal.
Adding new user codes
Other user codes can be added by entering the user menu and selecting the “Alarm > Users > Users” menu. Select a user from the list and press enter. This menu
can be used to enter a description and set a new code, for which confirmation will be requested.

10
Consult event log
Use this function to consult the event log. The control panel can log up to 1024 events. New events are stored in the log as event 0000. Event 1023 becomes 1024
and is then deleted from the log.
To consult the log:
1. Enter the installer code (default 001961) using the alphanumeric keypad and press the down arrow.
2. Move on to the Service menu using the navigation keypad and enter the menu by pressing Enter/Confirm.
3. Move on to the Event log menu using the navigation keypad and enter the menu by pressing Enter/Confirm.
»The possible options are as follows:
• Event memory: can be used to view the entire list of events.
• Alarm memory: only shows alarm events for the most recent arming period.
»The event type (activation or reset), the event description and the event date and time are shown first.
For more information, press the right-hand arrow on the navigation keypad; at this point all the other data will be shown.
To scroll through the log, use the up and down arrows on the navigation keypad. See below for a diagram illustrating navigation within the Event log.
»Each event has applicable attributes:
EventQual (Event qualifier)
R: for Reset
Empty: for activations
Event Event description
Time Time at which the event occurred
Date Date on which the event occurred
Who User or device that generated the event
Area Area in which the event occurred
Where Device on which the event was generated
EventID 4-digit number identifying the event
RxAck (Receipt acknowledgement)
RX for events that have been acknowledged by at least one recipient
NRX for events that have not been acknowledged
When consulting the event log, the list of events can be filtered according to the main categories using buttons 0 to 7.
Button Filter name Event groups shown
0 Reset filters All events
1 Alarms Alarms
2 Tampering Tampering
3 Exclusion Zone exclusion / activation
4 Battery / network faults Device battery faults, control panel battery faults, control panel electricity mains fault
5 Other faults System anomalies
6 Arming / Disarming Total arming, partial arming, disarming, forced arming
7 System operation System operations, technical programming