Commercial Electric 5516-VN User manual

□ □
1
Flush Mount Installation
2
PLACING THE ENCLOSURE
Place the Telecommunications Center (A) in the install
location. For the flush mount install you will not need (B)
Surface Mounting Brackets or (C) Surface Mounting Bracket
Screws.
Installation Guide
15 inch Telecommunication Center
Item # XXXXXXXXXX
Model #5516-VN
PACKAGE CONTENTS
MARKING THE SCREW LOCATIONS
Make sure the Telecommunication Center is level and
mark the two screw locations on the studs using a pen or
pencil.
CAUTION: When using tools always follow the
manufacturer’s safety guidelines.
Please read all instructions and safety information before use.
Retain this manual for future reference.
Safety Information
□
3 INSTALLING THE ENCLOSURE
Secure the two tabs to the studs using the included
Metal Wood Screws and a Phillips Head Screwdriver.
□
4 INSTALLING THE SCREW COVER
Once you have run wires and loaded the enclosure, you can
install the cardboard dust guard. Install the drywall over the
location. After sanding and paint you can remove the cardboard
dust guard. Complete installation by securing the cover (E) to the
enclosure using the included Cover Screws (D) and a Phillips
Head Screwdriver.
TOOLS NEEDED
Phillips Head Screwdriver
Utility Knife
Pencil/Pen
RoHS Compliant
Rev. 03/23/2020
Level
A
F- (4) Metal Wood Screws
E
F
D
5015295
ETL LISTED
CONFORMS TO
UL STANDARD 2416
CERTIFIED TO
CSA STD C22.2 NO
60950-1
NOTE: this enclosure is a distribution panel for low voltage
wiring systems. It is not designed to be used as an AC power
distribution panel. Use only Class 2 powered or passive devices.
Never install low voltage wiring during lightning storms. Never
install low voltage wiring in wet locations unless the wire is
specifically designed for wet locations
A- 15 in. Telecommunication Center
B- (4) Surface Mounting Brackets
C- (4) Surface Mounting Bracket Screws
D- (4) Screw Cover Screws

□ □
1
Surface Mount Installation
2PLACING THE ENCLOSURE
S M B (B) four
S M B S (C)
Installation Guide
Item # XXXXXXXXXX
Model #5516-VN
PACKAGE CONTENTS
A- 15 in. Telecommunication Center
B- (4) Surface Mounting Brackets
C- (4) Surface Mounting Bracket Screws
D- (4) Screw Cover Screws
MARKING THE SCREW LOCATIONS
Make sure the Telecommunication Center is level
and mark the four screw locations on the mounting
surface using a pen or pencil.
CAUTION: When using tools always follow the
manufacturer’s safety guidelines.
Safety Information
□
3 INSTALLING THE ENCLOSURE
□
4 INSTALLING THE SCREW COVER
Once you have run wires and loaded the enclosure, you can install
the cardboard dust guard. Install the drywall over the location.
After sanding and paint you can remove the cardboard dust guard.
Complete installation by securing the cover (E) to the enclosure
using the included Cover Screws (D) and a Phillips Head
Screwdriver.
TOOLS NEEDED
Phillips Head Screwdriver
Utility Knife
Pencil/Pen
RoHS Compliant
Rev. 03/23/2020
E- (1) Plastic Screw Cover
F- (4) Metal Wood Screws
NOTE: this enclosure is a distribution panel for low voltage
wiring systems. It is not designed to be used as an AC power
distribution panel. Use only Class 2 powered or passive
devices.
Never install low voltage wiring during lightning storms.
Never install low voltage wiring in wet locations unless the
wire is specically designed for wet locations
Please read all instructions and safety information before use.
Retain this manual for future reference.
D
F
B
C
A
5015295
ETL LISTED
CONFORMS TO
UL STANDARD 2416
CERTIFIED TO
CSA STD C22.2 NO
60950-1
Secure the Telecommunications Center using the
four included Metal Wood Screws and a Phillips
Head Screwdriver.
Level
E
15 inch Telecommunication Center