Commercial Electric DM-PN3A06-E User manual

THANK YOU
to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
We appreciate the trust and condence you have placed in Commercial Electric through the purchase of this EMERGENCY LED MODULE. We strive
improvement needs. Thank you for choosing Commercial Electric!
USE AND CARE GUIDE
EMERGENCY LED MODULE
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
SKU# 1005 579 050
Model # DM-PN3A06-E

2
Table of Contents
Table of Contents ................................... 2
Safety Information .................................. 2
Warranty .......................................... 2
Pre-Installation..................................... 3
Tools Required .................................... 3
Hardware Included................................. 3
................................. 3
Installation
Specification
.................................... 3-4
................................... 5
Maintenance
Operation
..................................... 5
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
□Turn off the power supply at the fuse or circuit breaker box
before you install the fixture.
□Do not make or alter any open holes in an enclosure of wiring
or electrical components during kit installation.
□
□
□
□
□
Do not use outdoors.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it
will not be subjected to tampering by unauthorized personnel.
The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.
Do not use this equipment for other than its intended use.
□
□
Account for small parts and destroy packing material, as these
may be hazardous to children.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
SAVE THESE INSTRUCTIONS
FCC STATEMENT
-This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
Use with grounded, certied, damp location rated xtures.
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
NOTE 2: Any changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Warranty
LIMITED WARRANTY
This product is warranted to be free from defects in workmanship and materials for up to 5 years from date of purchase. If it fails to do so,
please contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.
WARNING: Changes or modications not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
WARNING: To prevent wiring damage or abrasion, do not
expose wiring to edges of sheet metal or other sharp objects.
CAUTION: TEST ACCESSORY LEADS-OBSERVE PROPER
POLARITY WIRING
CAUTION: Use Rechargeable Battery Only
NOTICE: All electrical connections must be in accordance with local
and National Electrical Code (N.E.C.) standards. If you are unfamiliar
with proper electrical wiring connections obtain the services of a
qualified electrician.
Remove the fixture and the mounting package from the box and make
sure that no parts are missing by referencing the illustrations on the
installation instructions.
CAUTION: DO NOT MATE CONNECTOR UNTIL INSTALLATION
IS COMPLETE AND AC POWER IS SUPPLIED

3 HOMEDEPOT.COM
Please contact 1-877-527-0313 for further assistance.
Pre-Installation
Wiring Diagram
TOOLS REQUIRED HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Installation
Specication
1Take the at panel xture out from the package
and turn off the power supply before installation. 2Remove the cover plate that is pre-installed on
the back of the xture, keep the two screws.
Phillips
screwdriver
Slotted
screwdriver Power Drill Part DescriptionImage Quantity
AA
BB
CC
DD
EE
FF
GG
Emergency LED Bar
Cover Plate
Wire Nut
Screw
Screw
Indicator
1
Emergency module 1
1
2
1
2
1
INDICATOR
SWITCH
BLACK
WHITE LED DRIVER
EMERGENCY LED
LED ARRAY
AC-L
AC-N
DRIVER WITH
BATTERY
N
L
PG
2
1
4
5
6
7
8
LED-
LED+
Driver -
Driver +
3
NC
Emergency Driver Model No. Volts (V) Frequency (Hz) Watts (W)
DM-PN3A06-E 100V-277V 50/60 5
Current (mA) Max. Mounting Height
100 16.25ft (4.95m)
Battery Model No. Battery Type Charging Time (hour) Temperature Rating Ambient
18650 7.4V 2200mAh Li-ion Battery ≥24Hours Li-ion 0°C to 40°C (32°F to 104°F)

4
Installation
3
□ Remove the upper cover and lower cover on the
emergency module (AA). Take the LED bar (BB) and
the cover plate that have a hole in the middle (CC)
out from the emergency module (AA).
□ Tear off the heat-conductive double-side tape on
the LED bar (BB) and attach the LED bar (BB) to the
edge of the aluminum frame.
4
Mounting the cover plate that have a hole in the middle
(CC) to the xture with the two previously_removed
screws.
5
6
□ Remove the two knockouts on the upper cover
with a screwdriver.
□ Connect the two wires (black-hot, white-neutral)
from emergency module to the same color wires
from the power supply through one of the
knockouts with the wire nuts (DD).
□ Feed the electrical wires through the other one
of knockouts and attach to the indicator(GG).
□ Secure the upper cover to the emergency driver
with a screwdriver.
□ Secure the indicator (GG) to the proper lacation
with the two screws (FF).
Feed the electrical wires through the hole that in
the bottom of emergency module (AA),secure the
emergency module (AA) to the xture with a screw
(EE). Connect the two wires (red~LED+, black~ LED-).
Black
White
White

HOMEDEPOT.COM
Please contact 1-877-527-0313 for further assistance.
WARNING: Service by Qualied Personnel Only. De-energize
before opening.
5
Operation
□ AC Operation:
When AC power is present,the LED load from the LED driver is normal power supply, the emergency driver is charging in a
standby mode,the green light on the indicator on to indicate that it is charging. The emergency LED bar off in a standby mode.
□ Emergency operation:
When the AC power goes out,the emergency driver detects the AC power outage and automatically switch to the working
emergency mode.The green light on the indicator off, meanwhile the emergency LED bar on. When the AC power is restored,
the emergency driver backs to AC power working and starts re-charging, the emergency LED bar off, meanwhile the green
light on the indicatoron on.
Maintenance
□ Battery Replacement
Disconncet the emergency and normal input power sources before servicing. Remove the battery from the emergency driver,
replace the battery by qualied personnel, the replace battery only with Billda model 18650 7.4V 2200mAh.
□ Battery Disposal
Used batteries should be disposed of at an appropriate recycling center. Do not discard with normal housedhold waste.
Do not dispose of in re or water.
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.
FCC compliance information is listed as below:
Responsible party: Leedarson America, Inc.
Responsible party address: 300 Technology Court SE Suite 100, Smyrna, GA 30082
Telephone number: [phone]