CommScope M2400 Series User manual

www.commscope.com
Instruction Sheet 860481019
Issue 4, November 2012
M2400 and M2400A Patch Panel Instructions
© 2012 CommScope, Inc. All rights reserved
For RoHS Inquiries:
CommScope Inc.
Corke Abbey, Bray
Co. Dublin, Ireland
Attn: Legal Department
Page 1 of 7
General
The M2400 and M2400A modular panels are highly flexible 24-port, front or rear accessible patch panel
assemblies available in GigaSPEED, PowerSUM, or UNJ configurations. When installed with M-series or UNJ
information outlets, modular patch cords, and cables, they are an integral part of the CommScopeconnectivity
system. The panels mount in a standard 19-inch (483 mm) equipment rack with universal hole spacing.
Ordering information is listed below:
Material ID Part No. Description
760118323 M2400-1U-GS M2400 GS panel (GigaSPEED)
760118315 M2400-1U-PS M2400 PS panel (PowerSUM/UNJ)
760118349 M2400A-1U-GS M2400A GS panel (GigaSPEED)
760118331 M2400A-1U-PS M2400A PS panel (PowerSUM/UNJ)
M2400 Patch Panel M2400A Patch Panel
How to Contact Us
•To find out more about CommScope® products, visit us on the web at http://www.commscope.com/
•For technical assistance:
- Within the United States, contact your local account representative or technical support at
1-800-344-0223. Outside the United States, contact your local account representative or
Authorized Business Partner.
- Within the United States, report any missing/damaged parts or any other issues to
CommScope Customer Claims at 1-866-539-2795. Outside the United States, contact your
local account representative or Authorized Business Partner.
Tools Required
•Phillips head screwdriver

860481019
Instruction Sheet www.commscope.com
Page 2 of 7
Parts List
Verify parts against the parts list below:
Quantity
Description
M2400 Panel M2400A Panel
PS GS PS GS
1
1
―
―
M2400 panel assembly
―
―
1
1
M2400A panel assembly
2
2
―
―
Panel end caps
25
―
25
―
MPS/UNJ outlet caps
―
25
―
25
MGS outlet caps
4
4
4
4
12-24 x 1/2” mounting screws
2
2
2
2
Label sheet
1
1
1
1
Instruction sheet
Separately Orderable Items
A separately orderable rear cable management bar is available for use with the M2400/M2400A panel and a
separately orderable removal tool kit is required for use with the panel.
Material ID Description
760104737 Rack mountable rear cable management bar
760122713 Outlet removal tool kit (5 pack)
Step 1A – M2400 Flat Panel Installation (Skip to Step 1B for Installation of M2400A
Angled Panel)
Install Mounting Screws
12-24 x 1/2” screw
12-24 x 1/2” screw
1U panel
spacing
19-inch equipment rack
1. Partially install four 12-24 x 1/2” screws in equipment uprights in a 1U panel spacing as shown.

www.commscope.com
860481019
Issue 4, November 2012
Page 3 of 7
Install Panel on Rack
Align slots
in panel
with screws
Slide panel to right
to engage screws
12-24 x 1/2”
screw
1. Position panel against rack rails offset to the left of the partially installed screws.
2. Align slots in panel with screws and slide panel to right to engage screws.
Secure Panel to Rack
holes in panel
1. Use a screwdriver to access screws through holes in panel. Tighten screws to secure panel to rack.

860481019
Instruction Sheet www.commscope.com
Page 4 of 7
Install End Caps
Snap end caps into place
Panel
Rack
1. Snap end caps into place on panel as shown.
Step 1B – M2400A (Angled) Panel Installation
Install Panel on Rack
12-24 x ½” screws
19-inch equipment rack
M2400A panel 12-24 x ½” screws
1. Use four supplied 12-24 x ½” screws to secure panel to rack.
2. Connect cables to outlets per instructions provided with the individual outlets.

www.commscope.com
860481019
Issue 4, November 2012
Page 5 of 7
Step 2 ― Attach Separately Orderable Cable Management Bar
1U panel spacing
12-24 x 1/2” screws
M2400 panel shown
1. Attach cable management bar to rear of equipment rack using the four provided 12-24 x 1/2” screws as
shown. Bar should be level with lower row of outlets.
2. Assemble cable management bar components per instructions provided with the bar.
Step 3 – Terminate Outlets, Install Modular Caps on Outlets, and Populate Panel
1. Terminate cables to outlets per the instructions
provided with the individual outlets.
Note: Use a D914 impact tool (on HI setting)
with M110 cutting blade and hand puck or the
JackRapid* termination tool to punch down
conductors. Trimming conductors with side-cutters
or fine edge cutters is not allowed due to the tight
spacing of the outlets.
2. After termination of outlets, snap the provided
modular caps onto the outlets.
3. Populate the panel with outlets, then using the
instructions provided with the cable bar, route and
secure cables to bar using the provided hook-and-
loop straps.
*Trademark of Fluke Networks.
Modular cap

860481019
Instruction Sheet www.commscope.com
Page 6 of 7
Step 4 – Install Port Designation Labels and Icons
Labels for port
designation
Icons
1. Apply labels and icons to front of panel as shown for port designation.
Step 5 – Using Module Removal Tool (Part of Removal Tool Kit 760122713)
To Remove End Cap
Insert tool into slot
Slot
End cap
1. Insert provided tool into slot as shown.
2. Use tool to pry end cap loose from panel.

www.commscope.com
860481019
Issue 4, November 2012
Page 7 of 7
To Remove an Outlet
Locking tabs
M2400 panel shown
Removal tool
1. Position tool as shown and insert into front of outlet to depress locking tabs.
2. Remove outlet from rear of panel.
To Remove Modular Cap
Insert end of tool into
slot under cap
Slot
Pivot tool forward
to disengage cap
1. Insert tool into slot as shown and pivot forward to disengage modular cap for removal from outlet.