Comnet FVTR1D1A2C1M1 User manual

INS_FVTR1D1A2C1_REV–
6/16/10
PAGE 1
INSTALLATION AND OPERATION MANUAL
FVTR1D1A2C1(M)(S)1
10-BIT DIGITALLY ENCODED BI-DIRECTIONAL VIDEO
WITH 1 BI-DIRECTIONAL DATA CHANNEL,
2 BI-DIRECTIONAL 24-BIT AUDIO CHANNELS
AND 1 BI-DIRECTIONAL CONTACT CLOSURE
The FVTR1D1A2C1 is a bi-directional 10-bit video transmission system along
with one channel of bi-directional data, two channels of bi-directional audio
and one bidirectional contact.
The data channel is configured using a two position switch to operate as RS232,
RS422 or RS485, either two (2) wire or four (4) wire. See Figure 4 on Page 3
for details.
The FVTR1D1A2C1 may be directly plugged into the ComNet Rack (Part #C1) or
operated as a standalone module powered by the PS-9VDC power supply also
provided with the module. See Page 5 for mounting instructions.
The FVTR1D1A2C1 requires one optical fiber and may be supplied in a
multimode (M) or single mode (S) version.
See Figures 1 – 7 for complete installation details.

INS_FVTR1D1A2C1_REV–
6/16/10
PAGE 2
FIGURE 2 – FVTR1D1A2C1 TRANSCEIVER
FIGURE 1 – FVTR1D1A2C1 TRANSCEIVER
INSTALLATION AND OPERATION MANUAL FVTR1D1A2C1
NOTE: Remove Electrical Connector
for Rack Mount Units
REAR PANELFRONT PANEL
TECH SUPPORT: 1.888.678.9427
MULTIMODE OR
SINGLE MODE
OPTICAL FIBER
BLACK
BLACK WITH WHITE STRIPE
Power Supply:
Surface Mount: 8–15 VDC @ 2W
Rack Mount: From Rack
Video termination Switch
Set switch to TERM (Terminate)
when video is not looping to other
video devices or is the last device
in a looping configuration.

INS_FVTR1D1A2C1_REV–
6/16/10
PAGE 3
FIGURE 3 – SWITCH POSITIONS
The mode for each data channel is configured using a set of two switches on the front panel of the unit.
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVTR1D1A2C1
FIGURE 4 – DATA CONNECTIONS
RS232
Customer
Equipment FVTR1D1A2C1A
Customer
Equipment
FVTR1D1A2C1B
RS422
Bi-phase or
Manchester
DOUT(+)
DOUT(-)
DIN(+)
DIN(-)
Data In (+)
Data In (-)
Data Out (+)
Data Out (-)
2-Wire
RS485,
Sensornet
DIN(+)
DIN(-)
DIN(+)
DIN(-)
Data (A)
Data (B)
Data (A)
Data (B)
Data Transmit
Data Receive
Signal Ground
DIN(-)
DOUT(-)
GND
DOUT(-)
DIN(-)
GND
Data Receive
Data Transmit
Signal Ground
4-Wire
RS485
DIN(+)
DIN(-)
DOUT(+)
DOUT(-)
DOUT(+)
DOUT(-)
DIN(+)
DIN(-)
Data Out (A)
Data Out (B)
Data In (A)
Data In (B)
Data In (A)
Data In (B)
Data Out (A)
Data Out (B)
DIN(+)
DIN(-)
DOUT(+)
DOUT(-)
DOUT(+)
DOUT(-)
DIN(+)
DIN(-)
Data Out (+)
Data Out (-)
Data In (+)
Data In (-)
Data In (+)
Data In (-)
Data Out (+)
Data Out (-)

INS_FVTR1D1A2C1_REV–
6/16/10
PAGE 4
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVTR1D1A2C1
FIGURE 7 – LED INDICATORS
FIGURE 5 – AUDIO AND CONTACT CONNECTORS
AUDIO
CONTACT CLOSURE
FIBER VIDEO IN VIDEO OUT DATA AUDIO CONTACT POWER
GREEN Communication link has
been established over
optical fiber
An active video
signal is present
on the BNC
connector.
An active video
signal is present
on the BNC
connector.
An active data
signal is present
on the input pins of
the data connector.
(Solid or Blinking)
An active audio
signal is present
Closed Unit powered up
RED Communication link has
not been established
No video input
signal
No video output
signal
––––
OFF Not powered up correctly – No data signal No audio signal Open Unit powered down
FIGURE 6 – DATA CONNECTIONS
See Page 3 for Switch Settings
1) RS232
1 DIN (–)
2 DOUT (–)
3 Ground
2) RS422,
Manchester
& Bi-Phase
1 DIN (+)
2 DIN (–)
3 DOUT (+)
4 DOUT (–)
5 Ground
3) RS485 2-wire,
Sensornet
1 DIN (+)
2 DIN (–)
3 Ground
4) RS485 4-wire
1 DIN (+)
2 DIN (–)
3 DOUT (+)
4 DOUT (–)
5 Ground
Rear Panel

INS_FVTR1D1A2C1_REV–
6/16/10
PAGE 5
© 2010 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | [e-mail]
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: [phone] | F: [phone] | [e-mail]
INSTALLATION CONSIDERATIONS
This fiber-optic link is supplied as a Standalone/Rack module. Units
should be installed in dry locations protected from extremes of
temperature and humidity.
C1-US, C1-EU, C1-AU OR C1-CH CARD CAGE RACKS
CAUTION: Although the units are hot-swappable and may be installed
without turning power off to the rack, ComNet recommends that
the power supply be turned off and that the rack power supply
is disconnected from any power source. Note: Remove electrical
connector before installing in card cage rack.
1. Make sure that the card is oriented right side up, and slide it into
the card guides in the rack until the edge connector at the back
of the card seats in the corresponding slot in the rack’s connector
panel. Seating may require thumb pressure on the top and bottom
of the card’s front panel.
CAUTION: Take care not to press on any of the LEDs.
2. Tighten the two thumb screws on the card until the front panel of
the card is seated against the front of the rack.
WARNING: Unit is to be used with a Listed Class 2 or LPS power supply rated
9-12 VDC @ 1A.
IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may
be greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
MECHANICAL INSTALLATION INSTRUCTIONS
.313 [7.95 mm]
.156 [3.96 mm]
FIGURE A
Dimensions are for a standard ComNet™ two slot module