Comnet FVTR User manual

INS_FVTR_REV–
02/01/10
PAGE 1
INSTALLATION AND OPERATION MANUAL
FVTR
10-BIT DIGITAL BI-DIRECTIONAL VIDEO OR VIDEO SYNC
The FVTR(M)(S)1 series video transmitter/ receiver supports the transmission of
short-haul quality 10-bit digital bi-directional video or sync over one multimode
or single mode optical fiber.
This module is universally compatible with major CCTV camera manufacturers.
Plug-and-play design ensures ease of installation and no electrical or optical
adjustments are ever required. Bi-color (Red/Green) LED indicators are provided
for rapidly ascertaining equipment operating status.
These units are interchangeable between stand-alone or card mount
configurations. See Figure A on Page 4 for installation instructions.
See Figures 1 – 3 for complete installation details.

INS_FVTR_REV–
02/01/10
PAGE 2
NOTE: Remove Electrical Connector
for Rack Mount Units
FIGURE 2 – FVTRD TRANSCEIVER
FIGURE 1 – FVTR TRANSCEIVER
INSTALLATION AND OPERATION MANUAL FVTR
REAR PANELFRONT PANEL
TECH SUPPORT: 1.888.678.9427
Video termination Switch
Set switch to TERM (Terminate)
when video is not looping to other
video devices or is the last device
in a looping configuration.
MULTIMODE OR SINGLE MODE
OPTICAL FIBER
BLACK
BLACK WITH WHITE STRIPE

INS_FVTR_REV–
02/01/10
PAGE 3
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVTR
FIGURE 3 – LED INDICATORS
LINK VIDEO IN VIDEO OUT POWER
GREEN Communication
link has been
established over
optical fiber
An active video
signal is present on
the BNC connector.
An active video
signal is present on
the BNC connector.
Unit powered up
RED Communication
link has not been
established.
No video input
signal
No video output
signal
–
OFF Unit powered down

INS_FVTR_REV–
02/01/10
PAGE 4
© 2010 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | [e-mail]
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: [phone] | F: [phone] | [e-mail]
INSTALLATION CONSIDERATIONS
This fiber-optic link is supplied as a Standalone/Rack module. Units
should be installed in dry locations protected from extremes of
temperature and humidity.
STANDALONE MODULE:
The unit is provided with a mounting plate with holes for two No. 6
pan head screws (3 mm or 3.55 mm). Attach the module to a solid
piece of wood using two No. 6 pan head wood screws with a
minimum penetration into the wood of 3/4 inch. (Screws not
supplied). See Figure A.
RACK MODULE:
The unit is designed to be installed in the ComNet 19-inch (483-mm)
EIA standard card-cage rack, the C1-US, C1-EU, or the C1-CH. Follow
these guidelines to install rack cards after performing module setup
procedures.
C1-US, C1-EU, C1-AU OR C1-CH CARD CAGE RACKS
CAUTION: Although the units are hot-swappable and may be installed
without turning power off to the rack, ComNet recommends that
the power supply be turned off and that the rack power supply
is disconnected from any power source. Note: Remove electrical
connector before installing in card cage rack.
1. Make sure that the card is oriented right side up, and slide it into
the card guides in the rack until the edge connector at the back
of the card seats in the corresponding slot in the rack’s connector
panel. Seating may require thumb pressure on the top and bottom
of the card’s front panel.
CAUTION: Take care not to press on any of the LEDs.
2. Tighten the two thumb screws on the card until the front panel of
the card is seated against the front of the rack.
MECHANICAL INSTALLATION INSTRUCTIONS
WARNING: Unit is to be used with a Listed Class 2 or LPS power supply rated 9-12 VDC @ 1A.
WARNING: This unit should be installed in a restricted access location; available through the use of a lock and key or other means of security. Access should
be limited to service personnel who have been instructed about the reasons for the restrictions to the location. Any and all precautions should be taken and
controlled by the authority responsible for the location.
IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient
temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not
compromised.
FIGURE A
Dimensions are for a standard ComNet™ one slot module
.156 [3.96 mm]
.313 [7.95 mm]