Conlan C1000LP User manual

Manual
C1000LP_usermanual_ENGjun16
Keypad
C1000LP

2
Table of Content
1. Introduction
2. Installation
3. Programming users
3.1 User positions
3.2 Programming user codes
3.3 Programming user codes on
special positions
3.4 Smart enrolling
4. Battery Management
5. ConguringC1000LP
5.1 Service code
 5.2 Congurationoverview 
5.3 Changing Master Code
5.4 Changing Service Code
5.5 LED Indications
5.6 Outputs
5.7 Special settings
6. Blocking (Duress)
7. Manual reset
8. Technicalspecications
9. One-time/day code
page 3
page 3
page 4
page 4
page 4
page 5
page 6
page 6-7
page 8
page 8
page 8
page 9
page 9
page 10
page 11
page 12
page 12
page 12
page 13

3
1. Introduction
C1000LPisalowpowerkeypadthatworksonelectroninclockswithopencollector
and/or H-Bridge mode.
InstandbymodeistheyellowLEDislit(● ○ ○)
BycorrectcodelightsyellowandgreenLED(●● ○)
By incorrect code lights the red LED (○ ○ ●)
C1000LPhasabuzzerforindicatingwhilekeying,correctcode,incorrectetc.and2
transistoroutputs,independantfromeachother,sotheC1000LPcangiveaccessby
code.
TheC1000LPisastandaloneunit,thecanbeprogrammeddirectlybyMastercode
and Service code.
2. Installation
Mount the reader on a even surface.
Connectthewirestopowersupply,doorstrikeetc.(usesupplieddiode)
Wire colours
Note: Right after applying the voltage all LED’s lights and the buzzer sounds do not
touchthereaderuntilltheyellowLEDlightsandthebuzzerissilent.
2 - 16 VDC
0V GND
Output 2 open collector, 500 mA, 0V active
Output 1 open collector, 500 mA, 0V active
REX (IN2)
Feedback (IN1)
External controlling red LED, 0V active
External controlling green LED, 0V active
1 3
5
7 9
2
4 6
8
0

3. Programming users
Programming the C1000LP is simple and easy to understand.
3.1 User positions
C1000LPhas200userpositions,whichcancontainacode.Thepositionsaredivided
asfollowing:
User position Function
1 - 100 Activates output 2 (The code is position 1 is 1234 - factory default)
101 - 150 Activates output 1
151 - 190 Activates output 1 and 2
191 - 200 Reserved for special functions
3.2 Programming user codes
The Master code is used to program/change/delete the users. By default the Master
code is 4711.
LEDindication: Nolight:○ Lit: ● Flash: * Clear buer:
New users
(4711 - default) ○ ● ○ ●● ○ ●● ○  ○ ● ○
Toprogrammoreusers,continuefrom“Keyintheuserposition”orpress to
exit.
● ○ ○
Changing codes
It’sthesameprocedureasprogrammingnewusers,justoverwritetheuserposition.
#
Key in the
Master code #
Key in the
user position #
Key in the
user code
#
*
4

5
Delete specic users
(4711 - default) ○ ● ○ ●● ○ ○ ● ○ ● ○ ○
Delete all users
(4711 - default ○ ● ○ ○ ○ ●
○ ●
● ○ ○
3.3 Programmming codes for special functions
Programming the codes is described in 3.2 and 3.3. This entry activates the output(s)
for 5 seconds (factory setting). Only 1 user can enter at the time.
Programming the same user twice
Byprogrammingthesamecodeonthesamepositiontwicetogglestheoutput.
(Ie. the code is entered to unlock the door and entered to lock it again).
Programming the same user 3 times
Byprogrammingthesamecodeonthesameposition3times,theoutputisdesignat-
edasswitchononly.
(Ie. the door is permanently unlocked when the code is entered).
Programming the same user 4 times
Byprogrammingthesamecodeonthesameposition4times,theoutputisdesignat-
edasswitchoonly.
(Ie. the door is only locked when the code is entered).
#
Key in the
Master code #
Key in the
user position ##
#
Key in the Mas-
ter code #
Key in
2500 #

6
3.4 Smart enrolling
Thispositionmakesitpossibletoprogramcodesquickerwithoutenteringnewposi-
tions. Key in a position and it counts automatically to the next position. Codes can be
programmedalternativelyasyouseet.
○ ● ○ *● ○ * ○ ○ For more codes
repeat from
here.
Note:Thisprogrammingmodeoverwritesexistingpositions.
4. Battery management
Givesawarningbeforeopeningthedoor,whenthebatteryisatapprox10%charge.
PresetBatterylowwarning(1#):
Position Select chemistry Series cell count
0 Disable
1  Alkaline1,5V  (0,95V)3-10cells
2  Lithium3V   (2,3V)1-5cells
3  Li-poly/Li-ion3,7V (3,37V)1-4cells
4  LeadAcid2,1V  (1,95V)2-7cells
#
Key in the
Master code #
Key in
05 #
Key in the start
position #
Key in the code
○ ● ○ ●○ ●● ○ ○
#
Key in the
Service code #
Key in
08 #
Preset battery
Key in 1#
Select chemistry 
Series
cell count #
○ ● ○
○ ● ○
Hereisanexampleofhowyoupresetthebatterywhenhavinga12VLeadAcidwith6
cells.Seefollowinginstructions.
○ ● ○ ●○ ●● ○ ○
#
Key in
12347890 #
Key in
08 #
Key in 1# Key in 4
Key in 6#
○ ● ○
○ ● ○



7
Custombatterylowwarning(2#):
Ifyoudonothaveanyofthementionedbatterytypes,youcancustomizeyourbattery
size.Seefollowinginstructions.
Hereisanexampleofhowyoupresetthecustomizedbatterylowwarning.Inthis
examplewewantthebatterytosendawarningat10,8V.
○ ● ○ ● ○ ● ○ ○ ○
#
Key in
12347890 #
Key in
08 #
Key in 2# Key in 10 
Key in 80 #
○ ● ○
○ ● ○
○ ● ○ ●○ ●● ○ ○
#
Key in the
Service code #
Key in
08 #
Custom battery
Key in 2#
KeyinVoltage 
KeyinmVx10 #
○ ● ○
○ ● ○
Whenthebatteryisrunninglowitwillgiveyouawarningwhenyoutypeinyouruser
code.TheredLEDwillashwhilethebuzzerbeepsforabout3seconds.Theoutputis
hereafter activated.

8
5.CongurationofC1000LP
5.1 The Service code
The Service code is used for C1000LP’s advanced settings such as changing the Master
codeandServicecode,LEDindicationsandmuchmore.Theoverviewofthesettings
and the factory settings can be seen in 4.2 Conguration overview.
The Service code is 12347890 (factory setting).
Note: Before the Service code can be used must the voltage be turned OFF and
ON (the Service code can now be entered within 10 seconds).
After entering the Service code the reader is in programming mode (the green LED
lights). Each time a setting is made the C1000LP goes back to the previous point and
the next setting can be made.
Thenavigationisbyenteringtheposition/valuefollowedby#.
5.2Congurationoverview
Position Setting Factory default
00 Master code (1 to 8 digits) 4711
01 Service code (1 to 8 digits) 12347890
02  LEDindications   Normal=Yellow,active=Yellowandgreen
03 Outputs Output time for 1 and 2 is 5 seconds
04 Special functions
05 Smart enrolling
06 Input setup
07 Time
08 Battery management
09 Locker reserve time
2500 All codes on the user positions are deleted
0250 Reset to factory default
5.3 Changing the Master code
By default the Master code is 4711 and can onlybeusedtoprogram,changeordelete
usersontheC1000LP.TochangetheMastercode,enterthefollowing:
○ ● ○ ●● ○ ○ ● ○
Key in the
Service code #
Key in
00 #
Keyinnewcode
#

5.4 Changing the Service code
TheServicecodeisusedtoconguretheC1000LP’ssettings.
TochangetheServicecode,enterthefollowingwithin10secondsafterpoweron:
○ ● ○ ●● ○ ** ○ ○ ● ○
5.5 LED indications
TheC1000LP’s3LED’scanbeadjustedatwill.
ToadjusttheLEDindicationsenterthefollowing:
adjust the LED’s for standby indication (normal).
adjust the LED’s for correct code indication (active).
   adjustthekeyingindication(howtheLEDwillreactwhilekeying).
ToadjusttheLED’spressonthefollowing:
  =yellowLED(togglebypress)
= green LED (toggle by press)
= red LED (toggle by press)
  =buzzer(worksonlyonactiveandkeyingindication(togglebypress))
= save and go one step back
To save the settings press or press to go back to the previous point
(not saving).
#
Key in the
Service code #
Key in
01 #
Keyinnewcode # Repeatnewcode
#
02
#
1
#
2
#
3
1
2
3
0
#
9
***
***
***
***
#*

5.6 Outputs
The C1000LP has 2 outputs that can be set to H-Bridge output or open collector out-
put.BydefaultistheC1000LPsettoH-BridgeoutputwithLockdelayin5seconds.
Toconguretheoutputsettingsusethefollowingsteps:
○ ● ○ ○ ●●
sets the output 1 time in Pulse mode or Lock delay
sets the output 2 time in Pulse mode or H-Bridge time
sets the output 1 active position
sets the output 2 active position
sets the outputs functions
select the outputs for Daycode/onetime code
Pleaseusethecongurationschemeunder“03”sectionforcorrectnavigationforOC
setup
Note: In time setting for Pulse mode it is in Milisec x 10 instead of hours.
10
#
Key in the
Service code #
Key in
03
1
2
3
4
5
6

5.7 Special settings
These settings is used to change the C1000LP’s special functions such as turning the
buzzeron/oetc.
Tochangethesesettings,keyin:
 =Servicecodewithouttimeout(●= inactive / ●= active)
= Master code be changed by Master code (●= inactive / ●= active)
= Mute reader (●=O/●= On)
= Bell on OC1 (●=O/●= On)
= Onetime code (●=O/●= On)
= Day code (●=O/●= On)
= Locker mode (●=O/●= On)
 =Lockerreleaseonrenewtime(●=O/●= On)
Special positions
Userposition191to197canactivatespecialsetting3to6withacode.Theprogram-
ming is the same procedure as programming a user code just use the positions men-
tionedbelow:
191 = Toggle buzzer
194=Togglingthestarkeytoactivateoutput1(whitewire)
195 = Toggle onetime code mode
196 = Toggle Daycode mode
197 = Deactivate the user codes
198 = Seed code
199 = Digit count for one/day code
To save the settings press or press to go back to the previous step
(no saving).
Note:Incaseofpowerdisruptionthespecialfunctionswillgobacktothesetupmade
by service code.
11
#
04
●○ ○
1
2
3
4
5
6
#*
7
8

6. Blocking
The C1000LP is blocked for 1 minute after 4 incorrect codes.
LEDindication:○ ○ *
7. Manual reset
The C1000LP can be reset to factoty default manually.
•Turnthevoltageo.
•Connecttheyellowandbrownwire.
•Turnthevoltageon(2-16VDC)thereadersLED’slightsandthebuzzersounds.
•Turnthevoltageoanddisconnecttheyellowandbrownwire.
TheC1000LPisnowresettofactorydefaultandtheusercodesaredeleted.
8.Technicalspecications
Voltagerange: 2-16VDC
Mifarereading: Max.50mm
Output:  2xopencollector,max.500mA
Input:  Externalbuzzer/Feedback(brown)andREX,0Vactive(blue)
Rang:  IP67
Farve:  Blackorwhite
Kabel:  2,5meterwhite,8cores
Size(HxBxD): 130x50x8mm
12

9. One-time-/day code
TheC1000LPoers2advancedfunctionsofcodesthatcanbeusedonceonlyanda
code that is valid for a single day.
FirstthecodeshavetobegeneratedusingtheConlanCodeGenerator(download
availablefromwww.conlan.euoronitunesandGooglePlay).
Enteraseednumberintotherstbox.Thiscanbeanynumberfrom1to9999999.
Then enter the numbers of digits you require the code to have (best to avoid 4 or 8
digitscodessothereisnochanceofconictwithServicecodeorMastercode.The
system defaults to a 6 digit code.
Onceyoupresstheenterkey,thedaycodewillbeshownontheleftandaseriesof
one-timecodesshowninthetablebelow.Boththesecanbeexportedtoaleifre-
quired.
Whentheinformationisspecied,theC1000LPcanbeset:
Setting the time
○ ● ○ ● ○ ○ ○ ● ○ ●● ○
○ ○ ●● ○ ●○ ● ○
Activation of One-time-/day code
●**●= on, ● = o ○ ● ○ ● ○ ○
Finally,thereadermustknowhowmanydigitstheone-time-/daycodeshaveandthe
seednumber.Thisisdoneinthesamewayasprogrammingausercode:Position198
is for seed and position 199 is for digits.
13
#
Key in the
Service code #
Key in
07 #
Key in year
4 digits #
Key in month
2 digits
#
Key in day
2 digits #
Key in hours
2 digits #
Key in minutes
2 digits
#
Key in
04 #
Key in 5for one-time
code or 6for day code #
Conlan Code
Generator for
Windows, for
administration
of one-time and
day codes.
Conlan Day
Code app for
iOS and An-
droid units for
administration
of day codes
with SMS and
Email notica-
tion.