Conotec FOX-301 Series User manual

User’s Manual
1
Cautions for safety
Be sure to read cautions before use for correct use.
The specifications and exterior sizes described in this manual
may be subject to change for improving product capacity.
Name of each parts
Safety Precautions
1.This product was not manufactured as a safety device. Therefore, in case
of using it as a controller such as for a device that may cause casualty,
serious damage to peripheral devices, and tremendous loss of property,
be sure to attach double safety devices.
2.Do not wire or inspect or repair while power is on.
3.In case of supplying power, be sure to check a terminal number for connection.
4.This device should not be dissembled, processed, improved, or repaired.
Caution
• Before the installation of this device, understand fully how to use, safety regulations
or warnings, and be sure to use within specified related specifications or related
capacities.
• Do not wire or install it for a motor or solenoid with great inductive load.
• During the extension of a sensor, use a shielding wire, and do not make it unnecessarily
longer.
• Do not use the same power supply or any part that generates arc during closing or
opening directly near the power supply.
• A power line should be far apart from a high-tension wire, and the device should not be
installed in a place containing much water, oil, or dust.
• Do not install it in a place under direct light or exposed to rain.
• Do not install it in a place with strong magnetism or noise or vibration or impact.
• Put it far apart from a place that may release strongly alkaline or strongly acidic substance,
and use an independent pipe.
• Do not spray water directly on it for cleaning in case of installing it in the kitchen.
• Do not install it in a place where temperature/humidity exceeds rating.
• Take caution not to break a sensor wire or make any scratch.
• A sensor wire should be away from a signal line, power, and load line, and use an
independent pipe.
• In case of dissembling or modifying this product voluntarily, it may not be applied with
warranty service.
• A mark on the terminal circuit diagram is a safety mark as warning or caution.
• Do not use it near any device (harmonics welder, harmonics, harmonics radio, and
large capacity SCR controller) that generates strong harmonics noise.
• In case of using it with any other method than one designated by a manufacturer,
injury or loss of properties may occur.
• As it is not a toy, keep out of the reach of children.
• Installation must be done by a relevant professional or a qualified person.
• Our company shall not be responsible for any damage caused by failing to observe
the contents specified in the above warnings or cautions or by the fault of a consumer.
Danger
Caution, risk of electric shock
Electric Shock - Do not contact with AC terminal during current carrying.
This may cause electric shock.
Input power must be blocked when checking input power.
Models
Model Sensor Range Dimension Function
Temp./Humi.
control
RS485
Temp./
Humi. control
※FOX-301 series can be changed as followings :
Sensor HCPV-220NH is convertible
Sensor for temperature : FS-200N(NTC 10K)
Sensor for humidity : HCPV-220H
Converted temperature range : Upto -55.0 C ~ 99.9 C
humidity range : Upto 10~95%
Temp. measured value display(red)
Humi. meausred value display(green)
Humi. output display
Set value(UP) key
Humi. mode changing key
Set value(DOWN) key
Temp. mode changing key
Cooling output display
Set value display
Measured value display
Power
Heating output display
Dehumi. output display
Wiring terminal
Output : 250VAC 2A
Please make sure to use the power relay or a suitable magnet .
FOX-301AR1
yellow
green
black
white
red
Tempeature
sensor
Humidity
sensor
Temp./Humi. sensor
red
white
black
green
(shield) yellow
Sensor
Standard type
(Integral unit)
Customized
(Extended sensor)
Temp./Humi.sensor
series
shield
yellow
black
Sensor
Temp./Humi.sensor
red
white
Product exterior dimension
yellow green
black
white
red
Unit
<Front> <Wall-hanging> <Panel type> <Panel hole>
Temperature
Setting for temperature
present temperature
applied
applied
Heating temperature
setting
Cooling temperature
setting
Setting for temperature programs
press for more than 5 sec.
delay time
min.
deviation
temperature
°°
communication
address
communication
speed
corrected
present
temperature