Consew 146RBL-1A User manual

OPERATING INSTRUCTION
MODEL 146RBL-1A
146RB -1A
CONSEW INTEHNATIONAL LTD
Yomoiin BIdg.. 18. Uchom*. Hon-moehi. Higo*hi«ku. Otaka, 5^1 iooen.
P. O. Bok: Otoko Higoshi No. 50f
Talaehon**: Oioko [phone] *^3297
CobU Addf.ii; "CONSSWMACH" Oiokg
J6A459 CONSEW F©*; {06) 161-3298
•, X
V
From the library of: Superior Sewing Machine & Supply LLC

i. HOW TO USE MACHINE
1. NAMES OF MAIN PARTS
Hand Wheel
Spool pin
Feed Regulating dial
Feed reverse lever
Zig-zag width indicator
ob sa
J] Stoppers for zig-zag width indicator
Thread guide with three holes
Presser bar regulator screw
Thread take-up lever
Ufper Arm Thread guide
lower Arm Thread guide
Upper thread tension regulator
Tension post thread guide
Needle bar and needle bar thread guide
Presser foot
Throat plate
Slide plate
Feed dog
From the library of: Superior Sewing Machine & Supply LLC

2. SPOOL PIN
For the convepdent sake of packing, spool pin is
removed from the machine and packed separate in the
accessory box. Put the pin as shewn in Fig. 1 - #2.
3. SPEED
The machine is set to run at the speed of 3,000 r.p.m.
at the maximiin zig-zag width of 10 nrn. Jfaever, this speed
depends on the electric current and also the diameter of
the motor pulley being used.
In order to assure the durability of the machine,
•it is redanriended that the machine will be used at
the maximum speed of 2,500 r.p.m. at the beginning
of use.
4. OIUNG TO THE HX)K
Please supply a few drops of oil to the groove of the
rotating hook every day. (As arrcw-marked in Fig. 2)
(Fig. 2)
5. NEEDLE AND THREAD
—»K—
The size of the needle to be used should be determined by the
size of the thread as well as the materials to be sewn.
The needle should be set with its groove facing toward
you, as shown in the Fig. 3.
Ditch of Needle
Scooped portion
^feedle eye
Needle and Thread Chart
Thread size Needle Size
#120 -
#100 •# 9
100 - 80 11
80 - 60 14
60 - 40
16
40 - 20 19
20 -
16
21
From the library of: Superior Sewing Machine & Supply LLC

OILH^G
It is most irrportant that the machine is properly oiled
every day.
(Fig. 4)
One or two drops of oil would be supplied to all the
spots indicated in the Fig. 4.
7. AnXJIKIMENT OF ZIGZAG WIDTK AND FEEDIIC VOLIME
1) Mjustment of Zigzag width can be made by Zigzag
regulator dial. When straight sewing is required,
please place the dial to "O" ard gradually raising
numbers, zigzag width will be widened up to the
maximum width of 10 irm,
2. Feeding volume can be adjusted by feed regulation dial
and when it is placed to" "0", feeding is stepped.
^ raising the numbers ufward, the recjuired volume
is obtained and the maximum feeding volume is 5 im.
From the library of: Superior Sewing Machine & Supply LLC

HJW TO thre;^
Starting from the spool pin (1), please lead the thread
as per the follcwing manner.
(2) Three hole thread eyelet-
(3) Tension disc.
(4) Tension spring
(5) Tension post thread guide
(6) l^5per ann thread guide
(7) Take up lever
(8) Tension post thread guide
(9) lower arm thread guide
(10) Needle bar thread guide
(11) Needle
H3W TO WIND BOBBIN
(Fig. 5)
Page
If the bobbin thread does not wind evenly on the bobbin, this
will affect tte stitch and please be careful to wind the
thread to bobbin as per the following.
1. Push the bobbin on the bobbin winder spindle
as far as it will go.
2. Bring the thread forward toward the bobbin and
wind from below in clockwise direction several times
around the bobbin.
3. Push the bobbin winder lever downward until the wheel
contacts the drive belt, and then start the machine.
4. Mjustitent screw (4) can be turned in or out to increase
or decrease the anount of thread to be wound on the bobbin.
If the thread does not wind evenly on the bobbin, adjust
the tension thread guard by moving to right or
left as may be required. •
bobbin winder
(Fig. 6)
bobbin
From the library of: Superior Sewing Machine & Supply LLC

Page 5
10* INSERT^^^3 THE BOBBIN IN THE BOBBIN CASE
^ insert the fully wound bobbin in the bobbin case, hold it
fuyjers of your left hand and place
into ^ bobbui case with the thread tail remained outside.
remained thread tail through the slot of bobbin case,
under tension spring, then through the pig tail thread guide.
Fig. 7 - Names of Bobbin Case
Pig Tail
Tension spring
Latch spring
Slot
Tension screw
RFGUIATING TtE thread tension
Bobbin case,
For ordinary stitching, the tension of the upper and lower
thread should be equal so as to lock both threads in the
center of the fabric.
^e tension of the bobbin thread is regulated by rreans of the
tension screw, but it is preferable to keep it rather weak,
^ce it IS regulated, the perfect stitch can be obtained by
ad;]usting the tension of upper thread by increasing or
decreasing the tension.
12. REVERSE STITCH
^ machine, keep the feed reverse
4-? ^ <3epressed as long as required and if
^ease the lever, ordinary forward stitch will be done.
{For all other forward stitching, the lever remains in
up position).
From the library of: Superior Sewing Machine & Supply LLC

• Page
13. FEGULATIN3 PRESSURE Ol MAIERIAL,
Always use the lightest pressure possible to allow the
sinTOth feed of material. It can be adjusted by turning
regulating scr««r. Tp increase the pressure, turn
the screw to the right arid to decrease it to the left.
14. PREPARATION FOR SEWIN3
Presser bar
regulating screw
(Fig. 8}-
' -
/ r-
• •
1. Turn the balance wheel toward you withfiSse right hand
^til the needle moves down and up again to its highest
point, thus catching the lower (bobbin) thread.
.2. Now pull the end of the upper thread you are holding
and the bobbin thread will be grought i:p wi^ it
through the needle hole in the throat plate and
place both ends of the thread back under the presser foot,
3* Place the fabric to be sewn beneath the presser foot,
lower the foot i:qpon it and then start sewing the
machine. * .
TO REM3VE FABRIC AFTER SEIZING
Raise the needle bar to its highest point, lift the
presser foot and draw the fabric back and to jdie left.
Cut the ends of the thread a few inches long from the
needle.
From the library of: Superior Sewing Machine & Supply LLC

^age 1
II ADJUSTMENT
1- AOJUSTMENT for straight sewing (Ref. Fig. 9)
^ factory, the machine is so
adjusted that the zig-zag regulator is £ixed at "0".
If not, ple^e reset the indicator dial at "O" and run machine
to assure that accurate straight stitches be obtained.
Stould ypu fail to obtain accurate straight stitches by the
ple^ loosen regulator screw (A), then adjust zig-zag
^ noving it sldeway, until you obtain accu
stoaight stitches. Mter adjustment is made correctly, set the
screws (A) and (B) tight with indicator points "O".
2- AOJUSIMENr FOR CENTERINS THE NEEDLE (Itef. Fig. 10)
regulating dial for straight stitch sewing and
^ ha^^eel towards you until the needle reaches its lowest
stroke. See that the needle enters the
n^le slot in the throat (needle) plate at the very center. And
"®®ts the vertical center of needle,
o position. If it does not, adjust the needle bar fraire
pitman eccentric stud 'T)" (Fig. 11) by loosening the set screw "C".
3. AOJUSTMENr OF ZIGZA3 MDTOIENr (Ref. Fig. 11)
wrongly situated, make
of tte^^ reach Its lowest point and tighten the set screw "E"
the cam to come to the top, as shown in the Fig. 11.
Zugzag drive cam.
(Fig. 11).
Zigzag Regulator
B
(Pig. 9)
Needle bar frame pitman
C-J (Fig. 10)
Set screw Eccentric Stui Pin
Adjusting Screw A
Zigzag regulati
Knob
COiJ^L)
From the library of: Superior Sewing Machine & Supply LLC

AOTUSTMENT of upper feed mechanism. (Ref. Fig. 12)
(Fbr the type with upper feed mechanism^
146RB-1A and 146RBL-1A)
A* To increase the lifting volume of outer foot*
1.
loosen the adjusting belt A (/5'752).
2. Raise the position of Pock Shaft Crank (15^751)
as you desire.
3. Set the bolt tightly, after adjustn^t.
B. To obtain more lifting volume of outer foot.
1. Loosen the adjusting bolt B (#752) -
2. Raise the position of lifting crank connecting
line #748) as you desire.
3. Peset the iDOlt tightly, after adjustment.
C. To increase the feeding volume of order foot.
1. Loosen the adjusting bolt C. (#733).
2. Raise the position of feed correcting link (#732)
as you desixe.
3. Reset the bolt, after adjustment.
Page 8
From the library of: Superior Sewing Machine & Supply LLC

•• '] /"• . • , _ f, •.^.-
Page 9ftPOtSTMENT OF OPPER FEED MECHANISM
(Fig. 12)
From the library of: Superior Sewing Machine & Supply LLC