Controls MVP-A3235 User manual

Product Manual
Engine Control Module
Kubota Diesel Engines
Part Number: MVP-A3235
Revision: 2.2
Engine Type: Kubota Diesel with DPF Emissions Control
______________________________________________________________________________________________________________________________________
Copyright Controls, Inc.
P.O. Box 368 • Sharon Center, OH 44274
Phone [phone] • Fax [phone] • www.controlsinc.com

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
- 1 -
TABLE OF CONTENTS
INSTALLATION INFORMATION……...........………………………………...……………………………………………………………....2
CONNECTOR INFORMATION……...........………………………………...………………..………………………………………………….3
MENU NAVIGATION………………………………………………………………..……………………………………………..…………….…......5
MENU SYSTEM…………………………………………………………………...…………………………………………………..……………….…......6
OPERATOR MENU…………………………………………………………………..…………………………………………………..………….…......8
EMISSIONS PARAMETERS
ACTIVE FAULT CODES
STORED FAULT CODES
OPERATION EVENT LOG
ALARM EVENT LOG
ENGINE PARAMETERS
ENGINE IDENTIFICATION
MODULE INFORMATION
CONTROLER SETUP MENU……………………………………………………………………………………………….….…………...……..11
QUICK SETUP
PARAMETER CONFIGURATION
INPUT CONFIGURATION
THROTTLE CONFIGURATION
ENGINE SAFETY CONFIGURATION
MODULE CONFIGURATION
DISPLAY CONFIGURATION
MAINTENANCE CONFIGURATION
PANEL ENGINE SAFETY PROTECTION …………………………………….……………………………………......……..……..…17
PRE ALARMS AND ALARMS
SAFETY SHUTDOWNS
INDICATOR LAMPS
EMISSIONS MONITORING - REGENERATION……………………….……………………………………....……....……..…18
REGEN LEVELS
REGEN BUTTONS
PARKED REGENERATION PROCESS
REGEN STATUS
REGEN FAIL/ABORT

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
- 2 -
INSTALLATION INFORMATION

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
- 3 -
CONNECTOR INFORMATION
BATTERY +
CAN HIGH
CAN LOW
DIGITAL INPUT 1
FUEL LEVEL
BATTERY -
5VDC SUPPLY
NEUTRAL SWITCH
THROTTLE DOWN
THROTTLE UP
PARKING BRAKE SW
GROUND (B-)
1
2
3
4
5
6
1
2
3
4
5
6
Part# 3FK-108
Connector A Kit
(1) Deutsch DT06-6S plug
with (6) 0462-209-10614 sockets

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
- 4 -
PANEL CONNECTOR
Engine Harness Connector –Deutsch 21 pin (HDP24-24-21PE)
21 Pin Connector
Pin
Function
B
Battery Positive
E
Battery Negative
G
Key On Power
D
Crank Signal
V
J1939 High
U
J1939 Low
J
Alternator Excite
P
Neutral Switch Input
A
Parking Switch Input
Engine Harness
Connector (21 Pin)

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
- 5 -
MENU NAVIGATION
To access the control module menu system, power the unit and press the Menu button. While
pressing the menu button a message will appear to also press Enter to access.
Once you have accessed the menu system, the four key pad will be used for menu navigation and
therefore not available for engine speed control if the engine is running. The menu system is broken
into two main sections, the operator menu and the controller setup menu. The operator menu
contains information about the engine and control panel. The topics will vary based on the engine
type and control panel model. Pressing the Menu key will index the menu topic to the next item in
the list. The index is circular so you will eventually wrap around to the beginning of the operator
menu structure. Pressing the Enter key will index the topics backward. Once you have arrived at a
menu topic that you would like to explore more, press the Up arrow key. The Up arrow key will
index the screen each time it is pressed. Pressing the Down arrow key will index in the reverse order.
Pressing the Menu key at any time while in a topic will return you to the main menu topic heading.
To exit the menu, simply press the Menu and Enter keys simultaneously.

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
- 6 -
MENU SYSTEM
First Menu
Operator
Menu
Controller
Setup
Menu

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
- 7 -
OPERATOR MENU
Emissions Parameters
This menu allows for the viewing of the engine emissions data as broadcast by the ECU by pressing
the up arrow button. This data includes:
DOC Inlet Temperature
DPF Soot Load
DPF Inlet Temperature
Time at Last Regeneration
DPF Outlet Temperature
Active Regen Status
Regen Options
Regen Inhibit Status
DPF Differential Pressure
Active Fault Codes
This menu allows for the viewing of any Active Fault Codes as broadcast by the engine ECU by
pressing the up arrow button.
Stored Fault Codes
This menu allows for the viewing of any Stored Fault Codes as broadcast by the engine ECU by
pressing the up arrow button.
Operation Event Log
The operation log will record the engine start and stop events and tag them with the engine run
time hours. The Alarm can be viewed in the Operator menu area and can be cleared in the Module
Configuration section of the Controller Setup menu.
Alarm Event Log
Any monitored pre alarm or alarm will be recorded in the Operator menu section. The event will be
tagged with the actual engine run time hours at which the event occurred. The log stores the last 32
events and can be cleared in the Module Configuration section on the Controller Setup menu.
Engine Parameters
This menu allows for the viewing of unique engine information broadcast by the ECU by pressing
the up arrow buttons. This information includes:
Total Hours
Engine Torque
Requested TSC
Coolant Temperature
Rated Speed
Fuel Rate
Low Idle Speed
Manifold Temperature
Load at RPM
Potential Voltage

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
- 8 -
Engine Identification
This menu allows for the viewing on the engine model number and serial number.
Module Information
This menu allows for the viewing of the Module Part number and Software Version.
Controller Setup
When navigating through the Operator menu, you will arrive at the Controller Setup screen. To
configure the module to new settings, you can enter into this area by pressing the Up arrow key.
The next screen will ask for a password. If no password, or an incorrect password is used, navigation
into the menu is still possible and permitted, however, the ability to make changes will be restricted.
To enter the password, press the Enter key and brackets will appear. Use the Up and Down arrow
keys to set each digit individually, pressing the Enter key to index to the next digit from left to right.
Once the last digit is entered, the brackets will disappear and the digits will be represented with
asterisks. Pressing the Up arrow will index you to the Quick Setup menu and programming can
continue.

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
- 9 -
Navigating the Controller Setup menu structure is done in the same manner as the Operator menu
system. Menu will index to the next topic, The Up arrow will access the topic, etc. To make changes
to the settings, you will need to locate the item you are looking to modify under the appropriate
topic and then press the Enter key and the editing brackets will appear allowing you to make
changes to the value or change the selection. Once you have made your selection or changed the
value, simply press Enter again to accept it and the editing brackets will be removed.