Cooke & Lewis 3663602842019 User manual

V10617
GASUIT4 3663602842019
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 1 13/06/2017 16:45

1 2
IMPORTANT - Please read carefully the separate safety guide before use.
x1
[01] x1
[08] x1
[09] x4
(G30 28-30 mbar)
[10] x4
(G31 37 mbar)
[02] x1
[03] x2
[04] x1
[05] x2 [06] x1 [07] x4
[11] x4
(4 x 25mm)
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 2 13/06/2017 16:45

Installation
4
Use
13
Care & maintenance
15
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 3 13/06/2017 16:45

4
Installation
Caution:
The connection of the hob to the gas network or gas cylinder must be made by means of a rigid
copper or steel pipe with ttings complying with local regulations. These ttings are NOT supplied.
THIS OPERATION MUST BE MADE BY A QUALIFIED GAS INSTALLER
NOTE:
• The use of a gas cooking appliance produces heat and humidity in the place where it is installed.
• Therefore, you need to ensure the place is well ventilated, keeping the natural ventilation openings
clear and use a cooker hood for extraction.
• Intensive or prolonged use of the appliance may require additional ventilation including opening
a window.
• This appliance is only for at bottomed pans.
This appliance is to be used for the preparation of food and drink only, and must not be used as a
source of heat. Doing so may result in carbon monoxide poisoning and overheating of the hob.
Gas supply requirements
This hob is delivered pre-installed with gas jets (G20 : 20 mbar) suitable for natural gas. For use with
other gases, please consult the injector table later in these instructions.
Note: any change of jets MUST be carried out by a qualied gas installer only.
After completing the installation, ensure there is a gas tight seal around the bottom of all injectors
using foam. Press on the injector with your nger so that the gas outlet is closed and check for any
bubbles on the connection areas of the injectors.
Prior to installation, ensure that the local gas distribution and pressure are compatible with
this appliance.
Ventilation
This appliance must not be connected to a combustion products evacuation device. It shall be
connected and installed in accordance with local installation regulations paying particular attention to
the relevant requirements regarding ventilation.
What to do if you smell gas?
Do not try to light any appliance.
Do not touch any electrical switch.
Do not use phones in the building.
Immediately call your gas supplier from a different property.
WARNING: Read the instructions before using the appliance.
THIS APPLIANCE MUST BE EARTHED.
THIS HOB MUST BE INSTALLED BY A QUALIFIED GAS TECHNICIAN!
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 4 13/06/2017 16:45

5
01
≥760mm
≥150mm
≥150mm
≥55mm
≥760mm
Warning: Good ventilation is required around the appliance for easier dissipation of heat and low
power consumption. Sufcient clearance is required around the appliance as shown in the diagrams
above. The gap between the hob and any cupboard or extractor above it must be at least 760mm.
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 5 13/06/2017 16:45

6
02
560mm
490mm
[08] x1
Cut an aperture in the worktop using a jigsaw as shown. The worktop should be at least 30mm thick
and made of a heat resistant material.
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 6 13/06/2017 16:45

7
03
Seal the cut edge of the worktop using silicone sealant or PVA adhesive.
IMPORTANT: ensure that either product is fully cured as per the manufacturer’s instructions before
you commence installation of the hob. This hob MUST NOT be sealed or bonded into the worktop.
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 7 13/06/2017 16:45

8
04
[06] x1
[06]
Stretch out the supplied seal along the underside edge of the hob, ensuring the ends overlap.
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 8 13/06/2017 16:45

9
05
[01]
[01] x1
Once the worktop edge has cured, and the tape is tted, position the hob into the cutout in
the worktop.
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 9 13/06/2017 16:45

10
06
[07] x4
[11] x4
20-45mm
[07]
[07]
[11]
+45mm
Secure the hob to the worktop by attaching the brackets as shown.
Connection to the gas supply
THE CONNECTION TO THE GAS SUPPLY MUST ONLY BE MADE BY A QUALIFIED
GAS INSTALLER
• The connection of the hob to the gas pipe network or gas cylinder must be made by means of a
rigid copper or steel pipe with ttings complying with local regulations.
• A connecting elbow is pre-tted to the hob. This elbow terminates in an external 1/2” BSP
connecting thread complying with ISO 228-1:2003. The connection made to the pre-tted elbow
MUST be suitable for connecting to this thread. If ANY other connection type or thread size is used
a suitable adaptor MUST be tted.
• The qualied gas installer must ensure that the operation of the burners has been correctly veried
before use.
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 10 13/06/2017 16:45

11
Adjustment to a different type of gas
Caution: replacement of gas jets must only be carried out by a qualied gas installer.
Note: Extra gas jets are supplied to enable conversion for use with different gas types including liquid
petroleum gas (LPG) butane and propane. Details of the extra jets supplied and their applications
can be found in the Injector Table printed later in this manual. These jets must be replaced using a
dedicated specialist tool, not supplied.
Regulation of burners
Caution: The regulation described can only be carried out with burners that use methane gas and
city gas (where available), and the screw must be fully tightened in a clockwise direction on burners
using LPG.
Caution: The Minimum position on the burners MUST be adjusted by a qualied gas engineer only.
Regulation of the “MINIMUM” position on the burners.
To regulate the minimum position on the burners, follow the procedure below:
1. Turn on the burner and turn the knob to its MINIMUM position (small ame).
2. Remove the burner knob and turn the xing screw to the right or left until the ame of the burner
is regulated in the most suitable manner to MINIMUM and remains stable.
3. Make sure that the ame does not go out when changing the position quickly from MAXIMUM to
MINIMUM position.
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 11 13/06/2017 16:45

12
Connecting to the electrical supply
All installation must be carried out by a qualied electrician. Before connecting the mains supply
ensure that the mains voltage corresponds to the voltage on the rating plate.
Direct Connection
The appliance must be connected directly to the mains using an omnipolar circuit breaker with a
minimum opening of 3 mm between the contacts.
The installer must ensure that the correct electrical connection has been made and that it complies
with the wiring diagram.
The cable must not be bent or compressed.
Regularly check the power cord for damage. If the supply cord becomes damaged, it must be
replaced by the manufacturer, its service agent or similarly qualied persons in order to avoid
a hazard.
WARNING: This is a Class I appliance and MUST be earthed.
This appliance is supplied with a 3 core mains cable coloured as follows:
Brown = L or Live
Blue = N or Neutral
Green and Yellow = E or Earth
USE A 3AMP FUSE
DOUBLE POLE SWITCHED
FUSED SPUR OUTLET
EUR UK
(Blue)
(Brown)
(Green/Yellow)
N
L
N
L
N
L
FUSE ON
This appliance requires a 3 amp Miniature Circuit Breaker.
To avoid the risks that are always present when you use an electrical appliance it is important that
this appliance is installed correctly and that you read the safety instructions carefully to avoid misuse
and hazards. Please keep this instruction booklet for future reference and pass it on to any future
owners. After unpacking the appliance please check that it is not damaged. If in doubt, do not use the
appliance but contact Customer Services - see end of Care & Maintenance section for details.
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 12 13/06/2017 16:45

13
Use
Before you start
Switch on the appliance at the switched fused connection unit. The appliance is ready for use.
WARNING: Read the instructions before using the appliance.
Functions and settings
• Flame safety device (FSD): Stops the gas supply to the gas hob when the ame goes out.
• Auto ignition.
Injector Table
Gas Category UK & IR
II2H3+ (G20 20 mbar, G30 28-30 mbar, G31 37 mbar)
Type of
gas used
Type of
burner
Injector
marking
Rated
thermal
ow rate
kW
Rated
consumption
Reduced
heat
capacity
kW
Gas pressure
rating (mbar)
NATURAL GAS
(Methane)
G20
Auxiliary 0.72mm 0.95 91 lt/h 0.28
20Semi Rapid 0.97mm 1.75 167 lt/h 0.45
Rapid 1.15mm 2.90 276 lt/h 0.75
LIQUEFIED
PETROLEUM GAS
(Butane)
G30
Auxiliary 0.50mm 0.90 65 g/h 0.25
28-30Semi Rapid 0.65mm 1.65 120 g/h 0.40
Rapid 0.85mm 2.90 211 g/h 0.80
LIQUEFIED
PETROLEUM GAS
(Propane)
G31
Auxiliary 0.50mm 0.90 64 g/h 0.25
37Semi Rapid 0.65mm 1.65 118 g/h 0.40
Rapid 0.85mm 2.90 207 g/h 0.80
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 13 13/06/2017 16:45

14
Type of gas used Model
conguration
4 BURNERS
Rated thermal
owrate
(kW)
Total rated
consumption
G20 20 mbar 1AUX – 2SR – 1R 7.35 701 lt/h
G30 28-30 mbar 1AUX – 2SR – 1R 7.10 516 g/h
G31 37 mbar 1AUX – 2SR – 1R 7.10 507 g/h
Burner Minimum Pan
Diameter (cm)
Maximum Pan
Diameter (cm)
Auxiliary ≥10 ≤18
Semi Rapid ≥14 ≤24
Rapid ≥16 ≤26
Operation
Burner operation
• Push and turn the knob around to the spark zone of the control until the gas lights.
• Reduce the gas level to suit the cooking required.
• If the gas fails to light rst time, please try again.
CAUTION:
• If there is no electric current you can light the burners with a piezo electric spark
gas ignitor.
• The burners can only be lit with safety thermocouples when the knob is on MAXIMUM.
• Do not use cooking vessels on the hob that overlap the edges of the pan supports.
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 14 13/06/2017 16:45

15
Care & maintenance
Warning: Always switch off the electricity and gas supply before performing maintenance
work. In the event of a fault, contact customer services at the end of the care and
maintenance section.
Caution:
• Use soapy water and a cloth for cleaning. Never use abrasive powders.
• Avoid banging pots and pans down on the hob.
• Do not leave any empty pan on the heating zone.
Customer helpline (toll free):
UK 0800 324 7818 [email protected]
Eire 1800 932 230 [email protected]
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 15 13/06/2017 16:45

Manufacturer:
Kingsher International Products Limited,
3 Sheldon Square, London, W2 6PX,
United Kingdom
Distributor:
B&Q plc, Chandlers Ford, Hants,
SO53 3LE United Kingdom www.diy.com
SFD Limited, Trade House, Mead Avenue,
Yeovil, BA22 8RT, United Kingdom
TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 16 13/06/2017 16:45

TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 17 13/06/2017 16:45

TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 18 13/06/2017 16:45

TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 19 13/06/2017 16:45

TRAG10578 - 200000002 - 4 Burner Gas v3d Rv3.indd 20 13/06/2017 16:45