Cosatto NITTY GRITTY YO2 User manual

EN
Important: Keep these
instructions for future reference.
Important safety Information
General:
•The pushchair is suitable for children from birth up to a maximum user weight of 15kg.
•WARNING: Never leave your child unattended.
•WARNING: Ensure that all the locking devices are engaged
before use.
•WARNING: To avoid injury ensure that your child is kept away
when unfolding and folding this product.
•WARNING: Do not let your child play with this product.
•WARNING: This product is not suitable for running or skating.
•WARNING: Always use the restraint system.
•WARNING: Always use the crotch strap in combination with the
waist belt.
•WARNING: To avoid risk of injury from burning, do not place hot
beverage on cup holder.
•Do not use replacement parts or accessories other than those approved by Cosatto.
•A basket is provided for the carriage of 2kg of goods, evenly distributed.
•Any additional load attached to the handle or on the back of the backrest or on the
sides of the vehicle will aect the stability and safety of the vehicle.
•Do not use a platform with this product as it may render the product unsafe.
•Always apply the brake when placing or removing a child from vehicle.
•Never carry a second child on the product.
•This product complies with BS EN 1888:2012.
•Use the seat in the most reclined position for new born babies until they can sit up
unaided.
•Ensure your child wears a correctly tted and adjusted harness at all times. D-rings
are provided for the attachment of a separate safety harness approved to BS EN 13210
should this be required.

Visual language Key:
Refer to warning XX
Correct action
Lock
Unlock
Press and hold
Check
Continue to step XX
Repeat on other side
Incorrect action
Audible sound
Repeat action x times
General action arrow
Parts
1. Chassis
2. Rear wheel x2
3. Front wheel x2
4. Hood
5. Bumper bar
6. Footmu
7. Raincover
8. Raincover bag
9. Cup holder

1
2
34
7
9
8
5
6

Replacement Parts:
The replacement parts shown below are available for your product. For UK & Ireland
customers, order through our website: http://www.cosatto.com/service-centre/spares
For customer outside UK & Ireland, contact information for your local distributor can be
found on http://www.cosatto.com/stockists
If you require any further assistance, please contact us at [e-mail]
S1: Foam handle
S2: Handle pip
S3: Hood fabric
S4: Hood frame
S5: Headhugger
S6: Chest pads (pair)
S7: Auto lock
S8: Elbow joint badge
S9: Rear wheel
S10: Basket
S11: Harness
S12: Bumper bar
S13: Bumper bar cover
S14: Footmu
S15: Raincover bag
S16: Cup holder
S17: Front wheel
S18: Raincover
S14
S15
S18
S17
S16
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10 S11
S12 S13

Care & Maintenance:
Your pushchair has been designed to meet comprehensive safety standards, and with
correct use and maintenance will give many years of trouble free performance.
The chassis is strong but will weaken should the back wheels be bumped down stairs or
kerbs. Continual impact will cause damage.
If your child wears hard shoes these might damage the soft fabric.
Store your pushchair in a dry, safe place.
Storing a damp pushchair will encourage mildew to form, so after exposure to damp
conditions, dry o with a soft cloth and allow to dry thoroughly before storing.
Do not leave the pushchair in sunlight for prolonged periods - some fabrics may fade.
Regularly inspect the locking devices, brakes, wheels, harness assembly, catches, seat
adjusters, joints and xtures to ensure they are secure and in full working order. They
should move freely at all times.
Cosatto products are designed to operate with minimum maintenance, however regular
lubrication of moving parts will extend the life of your pushchair and make opening and
folding easier.
Should parts of your pushchair become sti or dicult to operate, apply a light
application of a spray lubricant e.g. silicone. Do not use oil or grease.
Wheels are subject to wear and should be replaced if necessary.
Your pushchair should be serviced and reconditioned before using it for a second baby,
or after 18 months, whichever is the sooner.
Hood may be cleaned by sponging lightly using warm water and a mild detergent.
Refer to the wash care label on soft goods for cleaning instruction.
Plastic and metal parts may be sponged clean with warm water and a mild detergent.
Never clean with abrasive, ammonia based, bleach based or spirit type cleaners.

Fitting & Operation information
Please refer to the following diagrams:
Wheels
1
Fitting
2
Removing
Pushchair
3
Opening
Release auto lock (1) then pull the handles upwards (2).
Press down on the locking lever (3) until a‘Click’ is heard and the release arm (4) is locked
in place.
Check the chassis has locked in place.
Brake
4
Applying
5
Releasing
Front wheel swivel lock
6
Applying
7
Releasing
Harness
8
Opening
9
Closing
10
Adjusting the strap length
Slide the strap adjustor to suitable length (1, 2 & 3).
11
Adjusting the shoulder strap position

12
Removing
Push shoulder strap retainer through backrest (1).
Push crotch strap retainer through seat (2).
Rotate“C” clip to expose its opening (3) and slide waist strap out of clip (4).
Retting is a reversal of this procedure.
Bumper bar
13
Fitting
14
Opening/Removing
Calf support
15
Opening
Hood
16
Fitting
Push the brackets onto the mounts on the chassis (1).
Attach the fabric fasteners to the inside of the seat unit (2).
Attach the fabric fasteners to the outside of the seat unit (3).
Fit the rear of the hood behind the backrest and attach the fabric fastener (4).
Attach the straps to the handle hinges (5).
17
Opening
18
Extending
19
Using the viewing window ap
20
Using the hood pocket
21
Closing
22
Removing
Removal is a reversal of step 16 .

23
Fabric removal
Using a ball point pen push in the button on the arm (1) then pull the arm out of the
hinge unit (2). The buttons are on the outside on the lower arms and the inside on the
upper arms. Pull the arms out of the hood fabric (3).
24
Retting
Backrest recline
25
Lowering
26
Raising
Basket
27
Removing
Footmu
28
Fitting
Open the harness 9and remove chest pad & headhugger (1).
Push the harness straps through the footmu (2).
Attach the footmu fabric fasteners to the rear of the backrest (3).
Ret headhugger & chest pads then close the harness.
Raincover
29
Fitting
Drinks holder
30
Fitting
Raincover
31
Fitting
Pushchair
32
Closing
Ensure backrest is in the upright position 26 .
Press down on the release arm (1) then pull the ring upwards (2).
Push the handles forwards (3) until the auto lock engages (4).

ES
Importante: Guarde estas
instrucciones para futura consulta.
Información de seguridad importante
General:
•La sillita está indicada desde el nacimiento y para niños de un máximo de 15kg.
•ADVERTENCIA: Supervise al niño en todo momento.
•ADVERTENCIA: Asegúrese de que todos los dispositivos de
bloqueo estén conectados antes de usar.
•ADVERTENCIA: Para evitar lesiones, asegúrese de mantener
alejado al niño al plegar y desplegar este producto.
•ADVERTENCIA: No permita que el niño juegue con este producto.
•ADVERTENCIA: Este producto no está indicado para correr o patinar.
•ADVERTENCIA: Use siempre el sistema de retención.
•ADVERTENCIA: Use siempre la correa de entrepierna en
combinación con el cinturón.
•ADVERTENCIA: Para evitar el riesgo de quemaduras, no coloque
bebidas calientes en el portavasos.
•No use piezas de repuesto ni accesorios que no sean los aprobados por Cosatto.
•Se incluye una cesta para el transporte de 2 kg de productos, distribuidos
uniformemente.
•Cualquier carga adicional acoplada al mango, a la parte trasera del respaldo o a los
lados del vehículo afectará a su estabilidad y seguridad.
•No use una plataforma con este producto, ya que podría afectar a su seguridad.
•Accione siempre el freno al colocar o quitar al niño del vehículo.
•No lleve nunca a un segundo niño en el vehículo.
•Este producto cumple con la normativa BS EN 1888:2012.
•Use el asiento en la posición más reclinada (“acostada”) para recién nacidos hasta que
se puedan incorporar sin ayuda.
•Asegúrese de que el niño lleve un arnés correctamente equipado y ajustado en todo
momento. Las hebillas en forma de D del arnés existente se suministran para acoplar
un arnés de seguridad separado aprobado por la norma BS EN 13210 de ser necesario.