Courtyard Creations TGS20SK User manual

PAGE 1 OF 2
Step 1:
Place the table top (#1) onto a non-abrasive surface,
such as a carpet, with its underside facing upwards.
Attention:
Make sure that each bolt needed for all steps
matches the corresponding figure to ensure
proper assembly.
HEX.KEY WRENCH 6MM
BOLT CAP M6
WASHER d6.5*D13*1.0
BOLT M6*25
BOLT M6*16
LEG
CENTER CONNECTOR
TABLE TOP
17KAA0201----Y4
18000337002
17C01A0706002Y4
17C01A0709002Y4
17FA05040301-Y4
62TMS20SKY101
TGS20SK-CS02
TGS20SK-CS01
1
8
8
4
8
7
5
6
4
4
1
1
4
2
3
MATERIAL CODE MATERIAL CODE
PART PART
Q’TY Q’TY
1
PARTS LIST
PART
NO.
PART
NO.
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
TGS20SK
FIGURE 1
COURTYARD CREATIONS INC.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely
assembled.
Do not sit or stand on this table.
Do not discard of any of the packaging until you have checked that you have all of the parts
and fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed
by children. Children should always be under direct adult supervision while using this
product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
!
!
!
!
!
!

PAGE 2 OF 2
Cleaning and Maintenance
Wash frame parts with mild soap and water,
rinse thoroughly, and dry completely. Do not
use bleach, acid, or other solvents on the frame
parts.
Wash glass with mild soap and water, rinse
thoroughly, and dry completely.
Inspect and tighten all bolts and fasteners on a
regular basis to ensure proper performance and
safety of your table.
When moving the table, lift.Do not drag this
table.
We recommend the use of furniture covers
when not in use.
In order to prolong the life and beauty of your
table, we recommend that it be stored in a dry
and protected area during off season periods.
Step 4:
Turn the table to its upright position. See Figure 4.
FIGURE 4
FIGURE 3
FIGURE 2
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
Step 2:
Fasten the legs (#2) to the underside of the table
top (#1) rim by using bolts (#4) and washers (#6).
Keep the bolts loose. See Figure 1 and Figure 2.
Step 3:
Fasten the center connector with ring (#3) to the
middle of the legs (#2) by using bolts (#5) and
washers (#6).
Make sure that all of the bolts have
been tightened completely and cover them with
bolt caps (#7). See Figure 3.