Craftsman 320.23465 User manual

Operator's Manual
ICRAFTSMRN°I
2.0 Amp Variable Speed
Multi-Tool
Model No. 320. 23465
_l_ WARNING: To reduce the risk
of injury, the user must read and
understand the Operator's Manual
before using this product.
c_ius
• WARRANTY
•SAFETY
•UNPACKING
•DESCRIPTION
•OPERATION
•MAINTENANCE
•TROUBLESHOOTING
•ESPANOL
Sears Brands Management Corporation Hoffman Estates, IL 60179 U.S.A.
www.craftsman.com

i _ =[e_[_e_'_
Warranty Page 2
Safety Symbols Page 3-4
Safety Instructions Page 5-9
Unpacking Page 9-10
Description Page 10-11
Operation Page 12-13
Accessory Tools Page 14-26
Maintenance Page 27-28
Troubleshooting Page 28
Exploded View and Parts List Page 29-31
Cratsman Repair Parts Phone Number Back Cover
CRAFTSMAN ONE YEAR LIMITED WARRANTY
FOR ONE YEAR from the date of purchase, this product is warranted
against any defects in material or workmanship. With proof of purchase,
defective product will be replaced free of charge.
For warranty coverage details to obtain free replacement, visit the
web site: www.craftsman.com
This warranty does not cover expendable parts such as accessory
blades, sandpaper or rasps.
This warranty is void if this product is ever used while providing
commercial services or if rented to another person.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
A
AlL WARNING: Some dust created by using power tools contains chemicals
known to the state of California to cause cancer and birth defects or other
reproductive harm.
SAVE THESE INSTRUCTIONS!
READ ALL INSTRUCTIONS!
This Multi-Tool has many features for making its use more pleasant and enjoy-
able. Safety, performance, and dependability have been given top priority in
the design of this product making it easy to maintain and operate.
23465 ManuaLRevised_10 0705 Page 2

The purpose of safety symbols is to attract your attention to possible dangers.
The safety symbols and the explanations with them deserve your careful
attention and understanding. The symbol warnings do not, by themselves,
eliminate any danger. The instructions and warnings they give are no substitutes
for proper accident prevention measures.
A_, WARNING: Be sure to read and understand all safety instructions in this
manual, including all safety alert symbols, such as "DANGER," "WARNING," and
"CAUTION," before using this Multi-Tool. Failure to follow all instructions listed in
this manual may result in electric shock, fire and/or serious personal injury.
SYMBOL MEANNING
_, SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION.
May be used in conjunction with other symbols or pictographs.
_, DANGER: Failure to obey this safety warning will result in death or serious
injury to yourself or to others. Always follow the safety precautions to reduce the
risk of fire, electric shock, and personal injury.
_, WARNING: Failure to obey this safety warning can result in death or serious
injury to yourself or to others. Always follow the safety precautions to reduce the
risk of fire, electric shock, and personal injury.
_lk CAUTION: Failure to obey this safety warning may result in death or serious
injury to yourself or to others. Always follow the safety precautions to reduce the
risk of fire, electric, shock and personal injury.
_, WARNING: To ensure safety and reliability, all repairs should be performed
at a Sears Parts & Repair Service Center.
DAMAGE PREVENTION AND INFORMATION MESSAGES
These inform the user of important information and/or instructions that could
lead to equipment or other property damage if they are not followed. Each
message is preceded by the word "NOTE" as in the example below.
NOTE: Equipment and/or property damage may result if these instructions
are not followed.
The operation of any power tool can result in foreign
WEARYOUR objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool
operation, always wear safety goggles or safety glasses
with side shields and a full-face shield when needed.
We recommend a Wide Vision Safety Mask for use over
eyeglasses or standard safety glasses with side shields,
available at Sears Stores. Always use eye protection that
is marked to comply with ANSI Z87.1.
23465 ManuaLRevised_10 0705 Page 3

Some of these following symbols may be used on this tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to
operate the tool better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
rain Minutes Time
Alternating Current Type of current
---== Direct Current Type or a characteristic of current
n O No Load Speed Rotational speed, at no load
] Class II Construction Double-insulated construction
.../rain Per Minute Revolutions, strokes, surface speed,
orbits, etc., per minute
Do not expose to rain or use in damp
Wet Conditions Alert locations.
To reduce the risk of injury, user must
Read The Operator's Manual read and understand operator's manual
before using this product.
Always wear safety goggles or safety
Eye Protection glasses with side shields and a full face
shield when operating this product.
Alert Precautions that involve
Safety your safety,
No Hands Symbol Failure to keep your hands away from the
blade will result in serious personal injury.
Failure to keep your hands away from the
No Hands Symbol blade will result in serious personal injury.
Failure to keep your hands away from the
No Hands Symbol blade will result in serious personal injury.
Failure to keep your hands away from the
No Hands Symbol blade will result in serious personal injury.
Hot Surface To reduce the risk of injury or damage,avoid contact with any hot surface.
23465 ManuaLRevised_lO 0705 Page 4

_, WARNING: Be sure to read and understand all instructions in this manual
before using the Multi-Tool. Failure to follow all instructions may result in electric
shock, fire and/or serious personal injury.
A_, WARNING: Do not attempt to operate this tool until you have thoroughly
read all instructions, safety rules, and warnings. Failure to comply with them can
result in fire, electric shock, or serious personal injury. Save the manual and refer
to it frequently.
GENERAL POWER TOOL SAFETY WARNINGS
_, WARNING: Read all safety warnings and instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or serious
personal injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There isan increasedrisk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or
unpluggingthe power tool. Keep cord away from heat, oil,sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
23465 ManuaLRevised_lO 0705 Page 5

When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electricshock.
NOTE: The term "residual current device (RCD)" maybe replaced by the
term "ground fault circuit interrupter (GFCI)" or "earth leakage circuit breaker
(ELCB)".
PERSONAL SAFETY
Stay alert, watch what you are doing, and use common sense when
operating a power tool. Do not use the tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattentionwhile
operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection.
Protective equipment, such as dust mask, non-skid safety shoes, hard hat,
or hearing protection, used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure that the switch is in the OFF
position before connecting to power source and/or battery, picking up,
or carrying the tool. Carrying power tools with your finger on the switch or
energizing in power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelryor
long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and
collection facilities, ensure that these are connected and properly used.
Use of these devices can reduce dust-related hazards.
POWER TOOL USE AND CARE
•Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and more safely at
the rate for which it was designed..
23465 ManuaLRevised_lO 0705 Page 6

•Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
Disconnect the plug from the power source and/or the battery from the
power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
•Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
•Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
•Use the power tool, accessories, tool bits, etc., in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
_, WARNING: When using power tools, basic safety precautions should always
be followed to reduce the risk of fire, electric shock, and personal injury.
_, WARNING: The operation of any tool can result in foreign objects being
propelled into your eyes, resulting in severe eye damage. When operating power
tool, always wear safety goggles or safety glasses with side shields and a full
face shield when needed.
,_ WARNING: If any parts are missing, do not operate the tool until the missing
parts have been replaced. Doing so could result in serious personal injury.
SERVICE SAFETY
•Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
If any part of this Multi-Tool is missing or should break, bend, or fail in any
way; or should any electrical component fail to perform properly: shut off the
power switch and remove the Multi-Tool plug from the power source and have
the missing, damaged, or failed parts replaced before resuming operation.
Tool service must be performed only at a Sears Parts & Repair Service
Center. Service or maintenance performed by unqualified personnel could
result in a risk of injury.
23465 ManuaLRevised_lO 0705 Page 7

Use only identical replacement parts when servicing a tool. Follow
the instructions in the Maintenance section of this manual. Use of
unauthorized parts or failure to follow maintenance instructions may create a
risk of electric shock or injury.
SPECIFIC SAFETY RULES FOR MULTI-TOOL
• Never use your Multi-Tool to perform sanding or separating operations in wet
conditions.
• Always wear eye protection.
• Always wear ear protection during extended periods of operation.
• Always wear a dust mask if the operation is dusty.
• Wear protective gloves when changing application accessories. Application
accessories become hot after prolonged usage.
• Always inspect for and remove all nails, screws, staples, etc. before sanding.
• Always check walls and ceilings to avoid hidden power cables and pipes. A
metal detector (available separately) is very helpful for this purpose.
• Whenever possible, use clamping devices or other suitable means to secure
the workpiece to a firm surface.
• When working with the machine, always hold it firmly with both hands and
provide for a secure stance. The power tool is guided more securely with
both hands.
Keep your workplace clean. Blends of materials are particularly dangerous.
Dust from light alloys can burn or explode.
Avoid unintentionally switching on the tool. Ensure that the on/off switch is in
the OFF position before connecting the tool to the power source.
Do not scrape wet or dampened materials (e.g. wallpaper) or on moist
surfaces. Penetration of water into the machine increases the risk of an
electric shock.
Do not treat the surface to be worked with solvent-containing fluids.
Materials being heated by the scraping can cause toxic vapors to develop.
Exercise extreme caution when handling the scraper accessory. The
accessory is very sharp; danger of injury.
Use only the original Craftsman accessories and the other accessories
(Fein _ Multi-Master accessories) available for this Multi-Tool, no others. FEIN
_Multi-Master is registered trademarks of FEIN Power Tools Inc.
Only use application accessories in good condition. Do not use them if they
are torn or worn.
23465 ManuaLRevised_lO 0705 Page 8

Do not restart a cutting operation in the workpiece. To resume a cutting
operation: while keeping the tool from contacting the workpiece, allow the
tool reach full speed and then carefully guide the cutting accessory into the
cut.
• Keep your hands away from the cutting area. Do not reach under the material
being cut.
• Hold power tools by their insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal parts of the tool "live" and
shock the operator.
1,WARNING: Wear ear protection. Exposure to noise can cause hearing
loss.
_, WARNING: To avoid injury, hold the tool by the insulated gripping surfaces
only. If the tool contacts hidden wiring or its own cord, exposed metal parts
of the tool could shock the operator and cause serious injury. Make sure that
hidden electrical wiring, water pipes, or other hazards are not in the cutting path.
_, WARNING: Your Multi-Tool should never be connected to the power
source when you are assembling parts, making adjustments, installing
or removing blades, cleaning, or when it is not in use. Disconnecting the
Multi-Tool will prevent accidental starting, which could cause serious
personal injury.
When unpacking the box, do not discard any packing materials until all of
the contents are accounted for:
1. Carefully lift the Multi-Tool out of the carton and place on a stable, flat
surface.
2. Open the color box to locate the following:
• Multi-Tool
• Circular Saw Blade
• Flush Cut Blade
• Carbide Triangular rasp
• Carbide Circular Blade
• Scraper Blade
• Sanding Base Plate
• 9 pieces Sandpaper (3pieces each of 60, 120, 180 grit )
• Hex Key
23465 ManuaLRevised_10 0705 Page 9

3.
• Vacuum Adapter
• Manual
Inspect the items carefully to make sure that no breakage or damage has
occurred during shipping. If any of the items mentioned is missing, (refer to
"PARTS LIST" illustration), return the Multi-Tool to your nearest Sears store
to have the Multi-Tool replaced.
A_, WARNING: If any part is broken or missing, do not attempt to assemble
the Multi-Tool, plug in the power cord, or operate the Multi-Tool until the
broken or missing part is replaced. Failure to do so could result in possible
serious injury.
CARTON CONTENTS/LOOSE PARTS (Fig. 1)
23465 ManuaLRevised_lO 0705 Page 10

ID]_.'_o_[[e_]
KNOW YOUR MULTI-TOOL (Fig. 2)
Fig. 2
LED worklight
On/Off switch Live tool indicator" LED light
cord
Vents
Vacuum adapter
Drive shaft
;}iiii[ii!iiiii[_
Flange bolt
Variable speed dial
Before attempting to use this Multi-Tool, familiarize yourself with all of its
operating features and safety requirements.
This Multi-Tool has the following features:
• A multifunction drive shaft system that allows the tool to be used for dry
sanding of small surfaces, corners and edges, for scraping, for sawing thin
steel sheet, wood and plastic by attaching different application tools supplied.
• 2.0 Amps, 11000 to 19000 oscillation per minute variable speed motor.
• Variable speed is controlled by the seed dail located on the back of the tool.
• LED worklight illuminates working area.
• "Live tool indicator" LED light shines green when the Multi-Tool is plugged
into a power source.
• The vacuum adapter can improve dust extraction, when it is installed on the tool
and connected with a dust-extraction system or a suitable vacuum cleaner.
PRODUCT SPECIFICATIONS
Input 2.0Amps
Oscillation Rate 11000 to 19000/Min
Oscillation Angle _+1.4 degrees
Rating 120 volts, 60Hz AC
Weight 2.71 Ibs (1.23 kg)
23465 ManuaLRevised_10 0705 Page 11

ON/OFF SWITCH (Fig. 3)
1.
2.
Connect the power cord of
your Multi-Tool to a standard
household power outlet.
To turn the tool ON, push
the on/off switch forward.
3. To turn the tool OFF, push
the switch backward.
Fig. 3
VARIABLE SPEED DIAL (Fig. 4)
The variable speed feature of
this Multi-Tool allows you to
match the proper speed to
the material being cut, sawed,
scraped or sanded, enhancing
the overall performance of
your tool and helping to save
the application accessory from
undue wear.
Fig. 4
1. The variable speed dial is
used to adjust the speed of the application accessory.
2. Turn the dial to increase or decrease the speed of the tool. (Fig.4).
3. Position "1" selects the slowest speed and position "6" selects the fastest
speed. Adjust the application accessory speed for optimum performance.
NOTE: Determine the optimum speed for by making a trial cut in a scrap piece
of material.
LED WORKLIGHT (Fig. 5)
The LED worklight, located
on the front of the tool, will
illuminate when the ON/
OFF switch is in the forward
(ON) position. This provides
additional light on the surface
of the workpiece for operation
in lower-light conditions.
The LED worklight will turn
off when the switch is slid
backwards (OFF).
Fig. 5
LED worklight
23465 ManuaLRevised_10 0705 Page 12

LIVE TOOL INDICATOR LED LIGHT (Fig. 6)
Your Multi-Tool has a "live
tool indicator" green LED
light, located on the back of
the tool. This light turns on
automatically when the Multi-
Tool is plugged into a power
source.
Fig. 6 Live Tool Indictor
LED light
23465 ManuaLRevised_lO 0705 Page 13

SELECTING THE APPLICATION ACCESSORY
_h, WARNING: If any part is broken or missing, do not attempt to plug in the
power cord or operate the tool until the broken or missing part is replaced.
Failure to do so could result in possible serious injury.
ACCESSORY
Carbide Circular Blade
Carbide Triangular Rasp
Scraper Blade
Circular Saw Blade
Flush Cut Blade
MATERIALS
Grout, Plaster, Porous Concrete
and Masonry
Hardened adhesives,
Thinset, Wood, Masonry
Paint & Varnish, Bonded Carpet,
Soft Adhesives, Vinyl Flooring,
wood and other floor coverings.
Wood, Plastic, Drywall, Non-
Ferrous Metals, thin Sheet Metal
and other materials
Wood, Plastic, Drywall, Soft
Metals and other Materials
Sanding Plate and Bare or painted wood, plaster,
and other surfaces, depending
Sandpaper on sandpaper grit ................................................................................................
ATTACHING THE ACCESSORY TOOL
_, WARNING: Failure to disconnect the tool from power source when
assembling parts, making adjustments, or changing accessories could result in
accidental starting causing possibly serious injury.
A_, CAUTION: For all work or when changing accessory tools, always wear
protective gloves. The sharp edges of the accessory tools will cause personal
injury. Accessory tools can be very hot while working.
_, WARNING: Check that the accessory tools are correctly attached. Incorrect
or insecurely fastened accessory tools can come loose during operation and
cause a hazard.
_, WARNING: Do not attach the circular saw blade, carbide circular blade,
scraper blade, or flush cut blade facing backwards, as operation in this
position may cause serious injury.
23465 ManuaLRevised_lO 0705 Page 14

NOTE: Replacement Craftsman accessories and additional Craftsman accessories
are available at Sears and Craftsman retailers. Refer to the model numbers for
purchase.
SANDPAPER KIT (67655)
DESCRIPTION (Fig. 7)
• 24 pieces sandpaper (8 pieces
each 60, 120 and 180 grit).
• Always apply to the
compatible sanding plate
(supplied with your Multi-Tool).
• Sandpaper kit is also
compatible with the Fein ®
Multi-Master tool.
Fig. 7
Q O
0
0 O
MOUNTING/CHANGING THE SANDPAPER (Fig. 8)
_, WARNING: Check that the
sanding plate and sandpaper Fig. 8
are correctly attached. An
incorrect or insecurely fastened
application tool can come
loose during operation and
cause a hazard.
1.
2.
3.
4.
!
Follow the directions for
Attaching the Application
Tool to attach the sanding
plate to the Multi-Tool.
Align the sandpaper with
the sanding plate and use
your hand to press it firmly
onto the sanding plate.
Press the sandpaper firmly against a smooth surface for a short period, then
switch on the tool. The burr will form a non-slip bond with the outer edge of
the sandpaper felt. This will avoid premature wear.
If one point has become worn, pull off the sandpaper, turn it 120 ° and place
it on the sanding plate again.
23465 ManuaLRevised_10 0705 Page 15

SANDING (Fig. 9)
_, WARNING: Do not touch
the gear box after prolonged
use; it could be very hot.
• The removal rate and the
sanding pattern are determined
by the choice of sanding sheet
and the work surface.
Apply uniform sanding
pressure to extend the life of
the sanding sheets.
Intensifying the sanding
pressure does not lead to
an increase of the sanding
capacity, but instead it increases wear on the machine and the sanding sheet.
Use only the tip or an edge of the sanding sheet for precise sanding of edges,
corners and hard to reach areas.
When selectively sanding on one spot, the sanding sheet can heat up
considerably. Remove the tool from the surface periodically to permit the
sanding sheet to cool down.
A sanding sheet that has been used for metal should not be used for other
materials.
1.
2.
3.
Use only original Craftsman sanding accessories.
For sanding, always connect dust extraction.
For Rough sanding use 40-80 grit paper.
For Smooth sanding use 100-180 grit paper.
For Fine sanding use 220-320 girt paper.
SAWING WITH THE CIRCULAR SAW BLADE (67651)
DESCRIPTION (Fig. 10)
• High speed steel circular
cutting blade.
Designed for cutting wood,
plastic, drywall, nonferrous
metals, thin sheet metal and
other materials.
• The circular saw blade is also
compatible with the Fein ®
Multi-Master tool.
Fig. 10
23465 ManuaLRevised_10 0705 Page 16

TO INSTALL THE CIRCULAR SAW BLADE
_, CAUTION: Wear protective gloves.
_, WARNING: Use sharp, undamaged saw blades only. Deformed, blunt saw
blades or saw blades that are otherwise damaged can break.
_1, WARNING: When sawing light building materials, observe the precautions
and the recommendations of the material suppliers.
WARNING: Plunge cuts may only be applied to soft materials, such as
wood, gypsum plaster boards, etc.
_I, WARNING: The sawing teeth are very sharp. Do not touch during mounting
and application.
_, WARNING: Do not attach Fig. 11
the circular saw blade facing
backwards (Fig. 11), which may
hurt the user.
1. Disconnect the Multi-Tool
from the power source.
2. Loosen the flange bolt with
the hex key provided.
(Fig. 12)
3. Ensure that the inner
threads and the drive shaft
are clean.
4.
5.
Align the grooves on the
circular saw blade with the
four raised ribs on the drive
shaft; put the blade on the
drive shaft. (Fig. 13)
With your gloved hand
holding the blade, put on
and tighten the flange bolt
using the hex key.
Fig. 12
Fig. 13
23465 ManuaLRevised_10 0705 Page 17

NOTE: The ribs on the
shaft and the grooves in the
accessory tools permit a firm
connection of the accessory
tools in increments of 30 °
around the shaft (Fig. 14).
Apply the accessory tool in the
orientation appropriate to the
task at hand.
CUTTING WITH THE
CIRCULAR SAW BLADE
(Fig. 15)
1. Connect the Multi-Tool to a
power source.
2. Securely clamp the
workpiece if necessary.
3. Draw the cutting lines on
the workpiece.
4. Apply the blade to the
workpiece.
5. Switch on the tool and
apply appropriate pressure
to make the cut.
Fig. 14
r---
23465 Manual_Revised_lO-0705 Page 18

CARBIDE CIRCULAR BLADE
(67650)
DESCRIPTION (Fig. 16)
The Carbide Circular Blade is
designed to cut out the grout
around wall tiles. It can also
be used to cut plaster, porous
concrete and masonry.
• Carbide-tipped, circular
grout disc.
• Designed for grout, plaster,
masonry or porous concrete
removal around the wall tiles.
Fig. 16
• The carbide circular blade is also compatible with the Fein® Multi-Master.
TO INSTALL THE CARBIDE CIRCULAR BLADE
A_, CAUTION: Wear protective gloves.
_lk WARNING: Do not attach
the carbide circular blade facing Fig. 17
backwards (Fig. 17), which may
hurt the user.
1. Disconnect the Multi-Tool
from the power source.
2. Loosen the flange bolt with
the hex key provided.
(Fig. 18)
3. Ensure that the inner
threads and the drive shaft
are clean.
Fig. 18
23465 ManuaLRevised_lO 0705 Page 19

4. Fig. 19
Align the grooves on the
carbide circular blade with
the four raised ribs on the
drive shaft; put the carbide
circular blade onto the drive
shaft. (Fig. 19)
5. With your gloved hand
holding the carbide circular
blade, put on and tighten
the flange bolt using the hex
key.
NOTE: The ribs on the
shaft and the grooves in the
accessory tools permit a firm
connection of the accessory
tools in increments of 30 °
around the shaft (Fig. 20).
Apply the accessory tool in the
orientation appropriate to the
task at hand.
Fig. 20
//_
w_/
23465 ManuaLRevised_lO 0705 Page 20