Craftsman 919.152361 User manual

ModeJ No.
919o751110
919,152361
o Safety Guidelines
o Assembmy
o Operation
o Maintenance
o
o Repair Parts
CAUT|ON: Read the Safety Guidelines
and All instructions CarefulIy Before
Operating.
Sears, Roebuck and Co., Hoffman Estates, mL60179 U.S.A.
Visit our Oraftsman website: www, sears,com/craftsman
A10087 Rev, 0 1/25/05

WARRANTY ................................................ 2
SPECIFICATION CHART ..................................... 3
SAFETY GUIDELINES=DEFINITIONS ........................... 3
IMPORTANT SAFETY INSTRUCTIONS ........................ 3-8
GLOSSARY ................................................ 8
ACCESSORIES ............................................ 8
ASSEMBLY ................................................ 9
INSTALLATION .......................................... 9-10
OPERATION ........................................... t 1-14
MAINTENANCE ............................................ 14
STORAGE ................................................ t 4
TROUBLESHOOTING GUIDE ................................ 15
REPAIR PARTS ............................................ 16
ESPANOL .............................................. t7-30
HOW TO ORDER REPAIR PARTS ...................... back cover
FULL ONE YEAR WARRANTY AiR COMPRESSOR
If this CRAFTSMAN Air Compressor fails due to a defect in material or
workmanship within one year from the date of purchase, Sears will at
its option repair or replace it free of charge= Contact your nearest Sears
Service Center (1-800-4-MY-HOME ¢_)to arrange for repair, or return the Air
Compressor to the place of purchase for replacement.
If this Air Compressor is used for commemia! or rental purposes, this warranty
applies for only ninety days from the date of purchase=
This warranty gives you specific legal rights and you may have other rights
which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
A10087 2= ENG

Model No, 919o751110
919o152361
Bore 1.875
Stroke 1.25
Voltage/Hertz/Phase 120/60/1
Minimum Branch Circuit Requirement 15 amps
Fuse Type Time Delay
SCFM@ 30 psig 2.5
Maximum Pressure 125 PSI
This manual contains information that is important for you to know and understand, This information
relates to protecting YOUR SAFETY and PREVENTING EQBtPMENT PROBLEMS, To help you
recognize this information, we use the symbols below, Please read the manual and pay attention to
these sections,
Indicates an
imminently hazardous
situation which, if not avoided, wHm
result in death or serious in'u_AQl.
which, if not avoided, coumd result in
death or serious injury..
Indicates a potentially
hazardous situation
which, if not avoided, _ result in
minor or moderate inulAQ_.
Used without the
safety alert symbol
indicates a potentially hazardous
situation which, if not avoided, may
result in property damacLe.
SAVE THESE iNSTRUCTiONS
IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT
IN SERIOUS INJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL
WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT.
_Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known (to the State
of California) to cause cancer, birth defects or other reproductive harm. Some example of
these chemicals are:
_' lead from lead-based paints
_' crystalline silica from bricks and cement and other masonry products
_' arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, always wear MSNA/NIOSN approved, properly fitting
face mask or respirator when using such tools.
When using air tools, basic safety precautions should always be followed to reduce the
risk of personal injury.
3= ENG A10087

Save these instructions
improper operation or maintenance of this product could result in serious injury and
property damage. Read and understand all warnings and operation instructions before
using this equipment.
m' J!!
WARNING: Risk of e×plosion or fire
What Could Happen
mtis normaR for eReetrical contacts
within the motor to spark.
mfelectrical sparks from inflator come
into contact with flammable vapors,
they may ignite, causing fire or
explosion.
Restricting any of the inflator ventiRation
openings will cause serious overheating
and could cause fire.
Unattended operation of this product
could resuRt in personaR injury or
property damage. To reduce the risk of
fire, do not allow the inflator to operate
unattended.
How To Prevent mt
Always operate the inflator in a well
ventilated area free of combustible
materiams, gasoline, or solvent vapors.
Store flammable materials in a secure
beation away from inflator.
Never phce objects against or on top
of inflator. Operate inflator in an open
area at least 12 inches away from any
wall or obstruction that would restrict
the flow of fresh air to the ventilation
openings.
Operate inflator in a clean, dry well
ventilated area. Do not operate unit in
any confined area.
ABways remain in attendance with the
product when it is operating.
Always disconnect ebctricam power by
moving on/off switch to the off position
and unpRug the power cord.
A10087 4-ENG

_m
WARNING: Risk of Bursting _[_J I
What Coumd Happen
ATTACHMENTS &ACCESSORIES:
Exceeding the pressure rating of air
operated accessories, tires, inflatable
balls, and other inflatables items can
cause them to expmode or fly apart, and
could result in serious injury.
Unattended tires, inflatable bans,
inflatabBe toys, and other inflatable
items can over inflate very quickly
sometimes in a matter of seconds and
resumt in personam injury or property
damage.
How To Prevent mt
Follow the equipment manufacturers
recommendation and never exceed the
maximum allowable pressure rating of
attachments or inflatable items.
ABways remain in attendance when
inflating tires, inflatabBe bans, inflatable
toys, and other inflatabBe items. Be
prepared to stop inflator when item is
fully inflated, sometimes in a matter of
seconds.
iiiiiii_, D
WARNING: Risk from FrayingObjects
What Could Happen Now To Prevent It
The inflator air stream can cause soft
tissue damage to exposed skin and
can propeB dirt, chips, loose particles,
and small objects at high speed,
resulting in property damage or personal
injury.
Always wear ANSI Z87.1 approved safety
gBasses with side shieMs when using the
inflator.
Never direct compressed air toward
any part of the body or at other people or
animals.
Always turn the inflator off before
attempting maintenance, attaching tools,
or accessories.
5= ENG A10087

_D
WARNING: Risk of Emectricam Shock I_ I
what Could Happen
Your inflator is powered by electricity.
Like any other electrically powered
device, If it is not used properly it may
cause electric shock.
Repairs attempted by unqualified
personnel can result in serious injury
or death by electrocution.
Electrical Grounding: Failure to provide
adequate grounding to this product
could result in serious injury or death
from electrocution.
See grounding instructions.
How To Prevent it
Never operate the inflator outdoors when
it is raining or in wet conditions.
Never operate inflator with protective
covers removed or damaged.
ABways replace damaged or worn
eRectric cords before operating inflator.
Any electrical wiring or repairs required
on this product should be performed by
authorized service center personnel
in accordance with national and local
electrical codes.
Make certain that the eBectrical circuit
to which the inflator is connected provides
proper eBectrical grounding, correct
voltage, and adequate fuse protection.
When operating inflator outdoors use
GFCI outlet.
WARNING: Risk to Breathing
What Could Happen How To Prevent It
The compressed air directly from your
inflator is not safe for breathing. The air
stream may contain carbon monoxide,
toxic vapors, or solid particles from
the tank. Breathing these contaminants
can cause serious injury or death.
Air obtained directly from the inflator
should never be used to supply air for
human consumption. In order to use air
produced by this inflator for breathing,
suitable filters and in-line safety
equipment must be property installed.
In=line filters and safety equipment used
in conjunction with the inflator must be
capaMe of treating air to aH applicable
Iocamand federal codes prior to human
consumption.
A10087 6-ENG

WARNING: Risk of Burns
What Could
Touching exposed metal such as the
inflator head or outlet tubes, can result
in serious burns.
Never touch any exposed metal parts
on inflator during or immediately after
operation, mnflator will remain hot for
several minutes after operation.
Do not reach around protective shrouds
or attempt maintenance until unit has
been allowed to cool.
WARNING: Risk from Moving Parts
What Could Happen
Moving parts such as the pulley, flywheel,
and belt can cause serious injury if they
come into contact with you, your clothing,
loose hair, or jewelery.
Attempting to operate inflator with
damaged or missing parts or attempting
to repair inflator with protective shrouds
removed can expose you to moving parts
and can result in serious injury.
How To Prevent It
Never operate the inflator with guards
or covers which are damaged or
removed.
Any repairs required on this product
should be performed by authorized
service center personnel
WARNING: Risk of FaIHng
What Could Happen
An inflator can fan from a table,
workbench, or roof causing damage to
the inflator and couBd result in serious
injury or death to the operator.
Now To Prevent It
Always operate inflator in a stabBe
secure position to prevent accidental
movement of the unit. Never operate
inflator on a roof or other elevated
position.
7- ENG A10087

iiiiiiii_,_,
WARNING: Risk of Unsafe Operation
What Could Happen
Unsafe operatien of your inflator ceu[d
lead to serieus injury or death to you
or ethers.
How 3"oPrevent Jt
Review and understand all instructions
and warnings inthis manual.
Become familiar with the operatien and
controls of the inflator.
Keep operating area clear of all persons,
pets,and obstacles.
Keep children away from the inflator at a[[
times.
Do not operate the product when
fatigued or under the influence of
alcohol or drugs. Stay alert at a[[ times.
Never defeat the safety features of this
product.
Equip area of eperation with a fire
extinguisher.
Do not operate machine with missing,
broken, or unautherized parts.
SAVE THESE INSTRUCTIONS
Become familiar with these terms
before operating the unit.
CFM: Cubic feet per minute.
SCFM: Standard cubic feet per
minute; a unit of measure of air
delivery.
£SlG: Pounds per square inch
gauge; a unit of measure of pressure.
Code Certification: Products that
bear one or more of the following
marks: UL, CUL, ETL, CETL, have
been evaluated by OSHA certified
independent safety laboratories and
meet the applicable Underwriters
Laboratories Standards for Safety=
Branch Circuit: Circuit carrying
electricity from electrica! panel to
outlet.
This unit is capable of powering the following Accessories. Accessories
included with your inflator:
inflation Needme: Used to inflate
sport bails.
Extension Nozzle: Used to inflate
small inflatable items such as air rafts
and beach balls.
High FBowinflator/Deflator adapter
body with three nozzmes and sea[
ring: Used to inflate or deflate air
mattresses, small boats, inflatable
toys, and other inflatable items that
use a large volume of low-pressure air.
A10087 8- ENG

Contents of Carton
1 - Inflator equipped with hose and
universal valve adapter
1 - Accessories Kit
1- Inflator Needle
1 - Extension Nozzle
1 - Nigh Flow Inflator/Defiator
adapter body with three
nozzles and seal ring
To Remove inflator from Carton
1. Grasp handle and lift the inflator
out of the carton.
2. Remove all packaging from
inflator and discard.
NOW TO SET UP YOUR UNIT 1, The cord set and plug with this
Location of the inflator
Locate the inflator in a clean, dry
and well ventilated area. The inflator
pump and housing are designed
to allow for proper cooling= The
ventilation openings on the inflator
are necessary to maintain proper
operating temperature. Do not place
rags or other containers on or near
these openings=
GROUNDmNG INSTRUCTIONS
Risk of Electrical
Shock. In the
event of a short circuit, grounding
reduces the risk of shock by
providing an escape wire for the
electric current. This inflator must
be propermy grounded.
The inflator is equipped with a cord
having a grounding wire with an
appropriate grounding plug (see
following illustrations). The ptug must
be used with an outlet that has been
installed and grounded in accordance
with all local codes and ordinances.
unit contains a grounding pin.
This plug MUST be used with a
grounded outlet.
IMPORTANT: The outlet being used
must be installed and grounded in
accordance with alI local codes and
ordinances.
2. Make sure the outlet being used
has the same configuration
as the grounded plug. DO
NOT USE AN ADAPTER, See
illustration.
Grounded
Outlets
Groundling Pin
3.
4.
Inspect the plug and cord before
each use. Do not use if there are
signs of damage.
If these grounding instructions
are not completely understood,
or if in doubt as to whether the
inflator is properly grounded,
have the installation checked by
a qualified electrician.
9- ENG A10087

Risk of Electrical
Shock, IMPROPER
GROUNDING CAN RESULT IN
ELECTRICAL SHOCK,
Do not modify the plug provided, If
it does not fit the avaiBable outlet,
acorrect outlet should be installed
by aqualified electrician,
Repairs to the cord set or plug
MUST be made by aqualified
emectrician,
Extension Cords
If an extension cord must be used, be
sure it is:
a 3-wire extension cord that has
a 3-blade grounding ptug, and a
3-slot receptacle that will accept
the ptug on the product
in good condition
no longer than 50 feet
16 gauge (AWG) or larger. (Wire
size increases as gauge number
decreases. 14, 12, 10, and 8
AWG may also be used.
Voltage and Circuit Protection
Refer to the specification chart for the
voltage and minimum branch circuit
requirements.
Certain inflators can be operated
on a 15 amp circuit if the following
conditions are met.
1. Voitage supply through branch
circuit is 15 amps.
2. Circuit is not used to supply any
other electrical needs (lights,
appliances, etc.).
3. Extension cords comply with
specifications.
4. Circuit is equipped with a
15 amp circuit breaker or 15
amp time detay fuse. NOTE: If
compressor is connected to a
circuit protected by fuses, use
only time delay fuses. Time delay
fuses should be marked "D" in
Canada and "T" in the US.
If any of the above conditions
cannot be met, or if operation of
the compressor repeatedly causes
interruption of the power, it may be
necessary to operate it from a 20
amp circuit. It is not necessary to
change the cord set.
A10087 10-ENG