Creality HALOT-LITE CL-89L User manual

HALOT-LITE
3D Printer User ManualV1.4HALOT-LITE
CREATE REALITY，ACHIEVE DREAMS

Dear Consumers,Firmware UpgradePlease login the official website https://www.creality.com/download, switch the language and select the relevant printer andmodel and download the required firmware, you can use it after the installation is finished. Thank you for choosing our products.For the best experience,please read the instructions before operating the Printer. Our teams will always be ready to render you the best services. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer. For a better experience in using our product, you can also learn how to use the printer in the following ways:View the accompanied instructions and videos in the U disk.Visit our official website www.creality.com to find relevant software/hardware information,contact details and operation and maintenance instructions.

NOTES 1
2
3
4
5
6
7
8
9
10 Do not use the printer any way other than described here in order to avoid personal injury or property damage.Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.Please use recommended resin to in case damage of machine.Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.Please do not open the plastic cover during usage, otherwise the printing will be interrupted.Do not wear cotton gloves when operating the printer. Such cloths may become tangled in the printers moving parts leading to burns, possible bodily injury, or printer damage.Please wait a moment after the print is finished. And please wear gloves to take out the print by tools. Children under 10 years should not use the printer without supervision. 11
12 Tips：Do not plug or unplug the power cord when power on.Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material off the frame,guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the print surface. Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Creality will not be responsible for any violators' legal liability under any circustance.

ContentsIntroduction 01-01Parameters 02-02Parts List03-0304-09Use the 3D Printer 10-12Start Printing 14-14Wiring Connection13-1315-17Troubleshooting Control remote printing

Hexalobular socket screw6Resin vat7Touch screen8
9USB port Power socket 10
Limit switch2Protective cover1Hexalobular socket screw3Leveling screw 4Buliding platform5
1. Introduction 1
2
3
4
5
6
7
8
9
10 01

2.Equipment parameters02Model NameHALOT-LITEUSB Disk, Creality Cloud3840*24000.05mm1-4S/layer250W330*301*572mm425*393*685mm13.5KG5 inch touch screenCommon rigid photosensivie resin, Standard resin, Hight hardness,High toughness, Dental model resin.Integral light source (wavelength 405nm)Win7/Win8/Win 10 64bit, Mac system (32-bit is not supported)192*120*200mm（length,width and height）Slicing Software Operation System Rated Power Build SizeTouch Screen Machine Size Package size Gross Weight Machine LanguagePrint Method Print speedCompatible Resin Rated VoltageLight Source TypeXY Axis Resolution XY Axis Accuracy Basic Parameters 100-240Va.c, 50/60Hz10.6KGNet Weight 中文(简/繁)/ English/ Español/ Deutsche/ Français/ Pусский/ Português/ Italiano/ Türk/Nederlands/Polskie/日本語/한국어Layer Thickness0.01-0.2mm

3. Package Content Print platform x 1 Resin vat x 1 3D printer x 1 Screwdrivers x 1setTool list
U disk x 1 Plastic blade x 1Metal blade x 1 Release film x 1 15
4
837Brush x 126Resin filter x 4Power cord x 1 9Vat cover x 1 Tips: the above accessories are for reference only, in kind prevail! 10Calibration card x 1 Calibration Card
校准卡片 03

4. Interface Information Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website of the latest firmware UI as the standard.Print04

4. Interface Information Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website of the latest firmware UI as the standard.Setting05

5. Level Platform 1. To calibrate the printing platform, first raise the platform, loosen the fixing screws on the left and right sides of the material trough, and take out the material trough;2. Loosen the four Leveling screw of the prototyping platform, attach Calibration card tightly to the print screen, press Settings → Z Axis Motion → Levelling（Refer to operating steps of levelling platform 2 for operation.）, to check whether the platform fits evenly with the paper. 3. After confirming that Calibration card fits evenly with the platform, screw up the four screws of the platform.Note: The printing platform has been leveled at the factory. If it needs leveling due to transportation or other reasons, please follow the steps below to adjust the printing platform.06

5. Level Platform Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website of the latest firmware UI as the standard.07

6. Load ResinPour the UV photosensitive resin into the resin vat. The slot capacity is 500ml/1000ml.Caution ：Resin may cause skin irritation or an allergic skin reaction. Please wear gloves before use to avoid direct contact with the skin.How to change resin: Tips：Take out the resin vat slowly, pour out the remaining resin into the container, clean the resin vat, pour in new resin, and then install the resin vat to the machine.
MAX LEVEL 1000ML
MAX LEVEL 500ML
1000ml500ml08

7. Release Film Instructions Installation steps(Thickness)0.15-0.2mm 95%(Light Transmittance )(Size)190mm*266mmParametersa.b.c.d.a.b.c.d.Finally, place the film-ring assembly back into the vat frame gently, then intall and tighten the fixing screws diagonally.First, remove the 14 screws at the bottom of the vat and take down the old release film.Prepare the new release film, peel off the the protective films on both sides of the release film. Align the holes and fit the release film on the clamping ring.The installed release film is as shown.09

8. Start Printing 1. Slicer2. If the model needs to add support, click the upper left icon to set corresponding parameters. eht evas→dehsinfi eb ot ecils rof gnitiaw 4sliced file You are welcome to find more details of slicing tutorial on the official website www.creality.com).”ecilS“ kcilC 3. Click icon ①→Setting slice printing parameters②→10ctb(.ctb)3D objects①②①② no ”nepo“ kcilc ,retnirp D3 DCL fo erawtfos eht nepO .1the left of the screen and add model file. slicer

2. Insert the U disk → press the print button. 2. Print1. Generate cxdlp file，and save the file to U disk. 8. Start Printing USB port
Warning: During the printing process, the machine can not be shaken, so as not to affect the printing quality.11ctb(.ctb)3D objectsfile name
Hide Folder
Save type
preservation cancel

8. Start Printing ;selfi tceleS .1
” ;arttS“sserp dna detnirp eb ot elfi eht tceleS .23. Printing···12

9. Control remote printing 2.Register3.Log in5. Scan QR Code7. Select device 8. check printing status9. Print Progress6. Device naming 1.Download4. Add equipment >>
>> >> >>
>> >> >>
HALOT-LITE
HALOT-LITE
HALOT-LITE 13

10.Wiring ConnectionZ motor driver portUV LED POWER EN portPower Supply portExhaust fanUL LED fan portUSB HOST portSpare brush firm-ware interfaceRGB screen portZ ends topLCD screen port14

11.Troubleshooting15

FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.FCC Statement16