Crestron TS-1542-IMCW User manual

TS-1542-IMCW
Interface Module for TS-1542
Installation Guide
TS-1542-IMCW Rack Mount (Exploded View)
Installing on a Level Surface
To prepare the TS-1542-IMCW to be mounted onto a level surface, ensure the unit is
attached to the included mounting bracket, as shown in the following illustration.
TS-1542-IMCW Bracket Mount (Exploded View)
Description
The TS-1542-IMCW is the interface module that is included with the TS-1542 HD Touch
Screen. It is also available separately to provide an additional plug-in connection point.
The touch screen connects to the interface module via a 8-pin RJ-45 connector.
The TS-1542-IMCW can be installed in a 1-gang electrical box, it can be rack mounted, or
it can be mounted on any at surface using the included mounting bracket.
Installation
Installing in a 1-Gang Box
To install the TS-1542-IMCW in a 1-gang box, mount the unit into the box, as shown in the
following illustration.
TS-1542-IMCW in a 1-Gang Box (Exploded View)
Rack Mounting
The TS-1542-IMCW can be mounted in a rack with other equipment using the four
mounting holes on the corners of the interface module, as shown in the illustration at the
top of the next column.
WARNING: To prevent bodily injury when mounting or servicing this unit in a rack,
observe the following guidelines:
• When mounting this unit in a partially lled rack, load the rack from the bottom to the
top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting
or servicing the unit in the rack.
Additional Resources
Visit the product page on the Crestron website (www.crestron.com)
for additional information and the latest rmware updates. Use a QR
reader application on your mobile device to scan the QR image.
Supplied Hardware
The hardware supplied with the TS-1542-IMCW is listed in the following table.
Supplied Hardware for the TS-1542-IMCW
Rack Mount Screws
(Not Included)
Rack Rail
Insert
TS-1542-IMCW
Hardware Hookup
Make the necessary connections as called out in the following illustrations. Apply power
after all connections have been made. When making connections to the TS-1542-IMCW,
use Crestron power supplies for Crestron equipment.
Hardware Connections for the TS-1542-IMCW (Front)
DESCRIPTION COLOR PART NUMBER QTY
Bracket, Mounting Black 2016054 1
Insert, for TS-1542-IMCW Black 4522556 1
Insert, for TS-1542-IMCW White 4522555 1
Screw, 6-32 x 3/16”, Pan Head, Phillips Black 2007203 2
Screw, 6-32 x 1”, Flat Head, Slot Black 2013235 2
1-Gang Electrical Box
(Not Included)
TS-1542-IMCW
Screws (2) 6-32 x 1"
Wall Plate
with Hardware
(Not Included)
Insert
Mounting Surface
Insert
TS-1542-IMCW
Screws (2) 6-32 x 3/16"
Mounting Bracket
TO PANEL:
Connect to TS-1542
via 8-Pin RJ-45 Cable
(Provided with TS-1542)

Hardware Connections for the TS-1542-IMCW (Rear)
LAN:
10BASE-T / 100BASE-TX
Ethernet to LAN
As of the date of manufacture, the SortName has been tested and found to comply with specications
for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(A)/NMB-3(A)
Crestron Electronics, Inc. Installation Guide - DOC. 7823A
15 Volvo Drive Rockleigh, NJ 07647 (2044929)
Tel: 888.CRESTRON 12.15
Fax: [phone] Specications subject to
www.crestron.com change without notice.
The product warranty can be found at www.crestron.com/warranty.
The specic patents that cover Crestron products are listed at patents.crestron.com.
Certain Crestron products contain open source software. For specic information, please visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and names of others.
Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.