Crestron TSW-732 Owner's manual

TSW-732
7" Room Scheduling Touch Screen
Supplemental Guide
Crestron Electronics, Inc.

Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive,
non-transferable Software Development Tools License Agreement. Crestron product operating system software is licensed to Crestron
dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements can be found on the Crestron
website at www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, and Rava are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or
other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities
claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is
not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.

Supplemental Guide – DOC. 7669A Contents
•
i
Contents
Access the Setup Screens 1
Configure the TSW-732 2
Ethernet Setup ........................................................................................................ 2
IP Table Setup ........................................................................................................ 3
Audio Setup ............................................................................................................ 5
Display Setup.......................................................................................................... 6
Standby Timeout..................................................................................................... 7
Diagnostics ............................................................................................................. 8
Keypad Test............................................................................................... 8
Touch Test................................................................................................. 9
Sensor Test................................................................................................ 9
Mic Test ................................................................................................... 10
LAN Test.................................................................................................. 10
Test Patterns............................................................................................ 11
Rava Test................................................................................................. 11
RTSP Test................................................................................................ 12
About .................................................................................................................... 13
Save & Edit ........................................................................................................... 13

Supplemental Guide – DOC. 7669A TSW-732: 7˝Room Scheduling Touch Screen
•
1
TSW-732:
7" Room Scheduling Touch Screen
Access the Setup Screens
The setup screens enable basic configuration prior to regular operation of the TSW-732
from Crestron®. To display the main setup screen, touch the screen while applying power to
the unit.
NOTE:
If no project has been loaded or if an invalid project has been loaded, the touch
screen defaults to the main setup screen.
During regular operation of the TSW-732, there are two ways to access the setup screens:
1. Place a button on the project main page and assign the reserved join number
(17242) that accesses the setup screens.
2. Press hard keys 1, 2, 3, and 4 to the left of the touch screen display in sequence,
twice (press 1, 2, 3, 4, 1, 2, 3, 4) within a 5-second period.
The
TSW-732 Setup
screen is displayed.
TSW-732 Setup Screen
The
TSW-732 Setup
screen is composed of buttons for Ethernet setup, IP table setup,
audio setup, display setup, standby timeout, and diagnostics. In addition, there are buttons
to toggle user project mode and system messages on or off. An
About
button provides
information about the touch screen, and a
Save & Exit
button saves settings and exits the
setup screens. The functions of each are detailed in the following pages of this guide.

2
•
TSW-732: 7˝Room Scheduling Touch Screen Supplemental Guide – DOC. 7669A
Configure the TSW-732
Ethernet Setup
On the
TSW-732 Setup
screen, tap
Ethernet Setup
to display the
Ethernet Setup
screen.
Ethernet Setup Screen
The
Ethernet Setup
screen displays the TSW-732’s MAC and IP addresses, subnet mask,
default router, primary and secondary DNS, hostname, and domain. There are controls for
turning DHCP on and off. When DHCP is off, a
Set Static IP Address Settings
button
provides access to controls that allow editing of these settings. This screen also contains a
link indicator to show the status of the Ethernet connection.
DHCP is enabled by default. To change to a static IP address, tap
Off
under
DHCP
Enabled
, and then tap
Set Static IP Address Settings
to display the
Ethernet Setup -
Static IPs
screen.
Ethernet Setup - Static IPs Screen
To edit the static IP address, static subnet mask, static default router, preferred DNS, or
alternate preferred DNS, tap the button directly under the label for the entry. The on-screen
numeric keypad opens.

Supplemental Guide – DOC. 7669A TSW-732: 7˝Room Scheduling Touch Screen
•
3
On-Screen Numeric Keypad
Use the keypad to make the new entry. Tap the “x” in the text field to clear any previous
entry. Tap to delete the last digit. Tap
Save
to save a new entry or to return
to the
Ethernet Setup - Static IPs
screen.
After new settings have been saved, tap
Reboot
on the
Ethernet Setup - Static IPs
screen
to reboot the TSW-732 so the new settings can take effect.
If not making any changes, tap to return to the
Ethernet Setup
screen.
Tap again to return to the
TSW-732 Setup
screen.
IP Table Setup
On the
TSW-732 Setup
screen, tap
IP Table Setup
to display the
Ethernet Setup - IP
Table
screen.
Ethernet Setup - IP Table Screen
The
Ethernet Setup - IP Table
screen displays up to four IP table settings, each of which
has an
Online
indicator. To add or edit an entry, tap the
Add/Edit
button to its left. The
Ethernet Setup - Edit IP Table Entry
screen is displayed.

4
•
TSW-732: 7˝Room Scheduling Touch Screen Supplemental Guide – DOC. 7669A
Ethernet Setup - Edit IP Table Entry Screen
Tap the field below
CIP ID
to display the on-screen hex keypad.
On-Screen Hex Keypad
Use the keypad to make the new entry. Tap the “x” in the text field to clear any previous
entry. Tap to delete the last digit. Tap
Save
to save a new entry or to return
to the
Ethernet Setup - Edit IP Table Entry
screen.
Tap the field below
IP Address/Hostname
to display the on-screen keyboard.

Supplemental Guide – DOC. 7669A TSW-732: 7˝Room Scheduling Touch Screen
•
5
On-Screen Keyboard
Use the keyboard to make the new entry. Tap
Cancel
to return to the
Ethernet Setup -
Edit IP Table Entry
screen. Tap the “x” in the text field to clear any previous entry. Tap
to delete the last digit. Tap
Save
to save a new entry and return to the
Ethernet
Setup - Edit IP Table Entry
screen.
On the
Ethernet Setup - Edit IP Table Entry
screen, tap
Save Entry
to save the current
entry or
Delete Entry
to clear it.
If not making any changes, tap to return to the
Ethernet Setup - IP Table
screen.
Tap again to return to the
TSW-732 Setup
screen.
Audio Setup
On the
TSW-732 Setup
screen, tap
Audio Setup
to display the
Audio Setup
screen.
Audio Setup Screen
The
Audio Setup
screen provides controls for muting or unmuting the audio and for
adjusting levels for the master volume, media volume, and beep volume. The
Media

6
•
TSW-732: 7˝Room Scheduling Touch Screen Supplemental Guide – DOC. 7669A
Volume
controls adjust the H.264 streaming media level in relation to the
Master Volume
controls.
Tap to return to the
TSW-732 Setup
screen.
Display Setup
On the
TSW-732 Setup
screen, tap
Display Setup
to display the
Display Setup
screen.
Display Setup Screen
The
Display Setup
screen provides controls to adjust the screen’s LCD brightness, green
key brightness, and red key brightness. Controls are also provided to enable using a hard
key or proximity sensor to wake the LCD. In addition, there are controls for the keys on the
left and right sides of the display. The controls turn the hard key lights on and off and toggle
the key colors between red and green.
Tap to return to the
TSW-732 Setup
screen.