Crestron Uc-brkt-100-z-assy User manual

The UC-BRKT-100-Z-ASSY simplifies installation of a Crestron® Flex UC conference system, providing all the necessary components connected and

mounted on a single VESA® compliant mounting bracket. The bracket mounts behind a display device in a conference room or directly to drywall

using the included anchors. The UC-BRKT-100-Z-ASSY is intended for use with the M-Series, B-Series, and C-Series of Crestron Flex conference

systems. For more information, visit www.crestron.com/flex.

Check the Box

Item Qty

Anchor, Drywall, Plastic, 3/8 in. x 1/2 in. (P/N 2052565) 2

Key, Anchor (P/N 4529654) 1

Bit, Spanner, #6 (P/N 2052847) 1

Screw, 6-32 x 3/8 in., Undercut Head, Spanner (P/N 2052846) 2

Screw, 8-AB x 1-1/2 in., Pan Head, Combo (P/N 2052567) 2

Power Cord (P/N 2053985) 1

Tie Wrap (P/N 2047935) 4

Install the Wall Bracket Assembly

The wall bracket can be mounted to VESA compliant display devices or building structure. Anchors and screws are also supplied for installation on

walls 3/8 in. to 3/4 in. thickness.

NOTES:

• The integrated cable tie wraps are reusable. Take care to avoid damage to the cable tie wraps.

• The wall bracket assembly includes an opening and pass through screw holes for placement over a single gang US electrical wall box that can

be covered by a decorative wall plate. If the wall plate opening will be positioned over an electrical wall box, longer screws will be needed to

secure the decorative wall plate to the electrical box. Do not attempt to secure the wall bracket assembly with the wall plate opening screws.

UC-BRKT-100-Z-ASSY (connecting cables not shown)

14.00 in.

(356 mm)

100 mm

200 mm

UC-ENGINE-Z

Connector Cover

Wall Plate Opening

Power Pack

Reusable Cable Tie Wrap (x4)

7.00 in.

(178 mm)

16.00 in.

(406 mm)

6.70 in.

(170 mm)

15.44 in.

(392 mm)

5.00 in.

(127 mm)

14.92 in.

(378 mm)

13.42 in.

(341 mm)

13.45 in.

(342 mm)

HD-CONV-USB-200

300 mm

UC-BRKT-100-Z-ASSY

UC Engine Assembly

Open the Connector Covers

UC-ENGINE-Z

Connector Cover

Connect Devices

Connect touch screens, conference systems, display devices, network cables, and peripherals to components on the UC-BRKT-100-Z-ASSY. Refer to

the quick start guide included with the Crestron Flex UC System.

CAUTION: The bracket assembly has cables and devices that are connected at the factory. DO NOT DISCONNECT ANY DEVICES OR CABLES THAT

ARE ALREADY CONNECTED.

Secure Connector Covers

Connector Cover

NOTE: For additional security, replace the screws with the included spanner screws. A 1/4 in. driver bit is supplied to install the spanner screws.

For Additional Information

Scan or click the QR codes below for detailed product information.

UC-BRKT-100-Z-ASSY Flex Solutions

Compliance and Legal

Original Instructions: The U.S. English version of this document is the original instructions. All other languages are a translation of the original instructions.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of