Crestron UC-BRKT-150-ASSY User manual

The UC Engine Assembly (UC-BRKT-150-ASSY) simplifies installation of a
Crestron Flex UC system, providing all the necessary components
connected and mounted on a single VESA® compliant mounting bracket.
The bracket mounts behind a display device in a conference room. The
UC-BRKT-150-ASSY is intended for use with Crestron Flex conference
systems. For more information, visit www.crestron.com/flex.
In the Box
1 UC-BRKT-150-ASSY UC Engine Assembly
2 Anchor, Drywall, Plastic, 3/8 in. x 1/2 in. (2052565)
1 Bit, Spanner, #6 (2052847)
1 Key, Anchor (4529654)
2 Screw, 6-32 x 3/8 in., Undercut Head, Spanner (2052846)
2 Screw, 8-AB x 1-1/2 in., Pan Head, Combo (2052567)
1 Power Cord (2053985)
1 Power Pack (2045870)
4 Tie Wrap (2047935)
Installation
The wall bracket can be mounted to VESA compliant display devices or to
a wall or other building structure. Anchors and screws are also supplied
for installation on walls 3/8 in. to 3/4 in. thickness.
CAUTION: The bracket assembly has cables and devices that are
connected at the factory. DO NOT DISCONNECT ANY DEVICES OR
CABLES THAT ARE ALREADY CONNECTED.
NOTES:
lThe integrated cable tie wraps are reusable. Take care to avoid
damage to the cable tie wraps.
lThe wall bracket assembly includes an opening and pass through
screw holes for placement over a single gang US electrical wall
box that can be covered by a decorative wall plate. If the wall
plate opening will be positioned over an electrical wall box, longer
screws will be needed to secure the decorative wall plate to the
electrical box. Do not attempt to secure the wall bracket
assembly with the wall plate opening screws.
UC-BRKT-150-ASSY Quick Start
1

Open the Connector Covers
Remove connector covers prior to making UC-ENGINE connections on
the UC-BRKT-150-ASSY.
UC-BRKT-150-ASSY Quick Start
2

Secure Connector Covers
After completing UC Engine connections, secure the connector covers
using a #1 Phillips head screwdriver to replace the screws.
NOTE: For additional security, replace the screws with the included
spanner screws. A 1/4 in. bit is supplied to install the spanner screws.
Visit the Product Page
Scan the QR code to visit the product page.
www.crestron.com/model/6511041
UC-BRKT-150-ASSY Quick Start
3

Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. VESA is either a
trademark or registered trademark of Video Electronics Standards Association in the
United States and/or other countries. Other trademarks, registered trademarks, and
trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not responsible for errors in typography or
photography.
©2020 Crestron Electronics, Inc.
Doc ID 8586A
(2054979)
04/07/20
UC-BRKT-150-ASSY Quick Start
4