CrimeStopper CS-2013FM User manual

2-Way FM Remote Start & Alarm System
CONGRATULATIONS! on your choice of a CS-2013FM 2-Way FM Paging Remote Alarm/Remote Starting System
by Crimestopper Security Products Inc. This booklet contains the information necessary for installing, using, and
maintaining your alarm system. If any questions arise, contact your installation dealer first, or Crimestopper
Security Products Inc. at the Tech Support number listed below. This system is designed for single vehicle
operation. The Remote start functions of this system are designed for use with automatic equipped transmission,
fuel injected vehicles only. This system is compatible with diesel engines.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Siren,
L.E.D., Power, Ground, Door pin, Hood pin (Remote Start Inhibit) etc.
-OPTIONAL: These are features to be connected only if desired or agreed upon by the installing dealer (i.e. Door
Locks, Starter Disable, Trunk, and Auxiliary Remote Output etc.)
Note: Additional labor and parts will be required for some features and on vehicles equipped with Factory Anti-
Theft Systems such as GM PassKey®/Passlock®/VATS, or Key-FOB based RF Transponder systems such as
FORD P.A.T.S.®
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific Standard Time
Website: www.crimestopper.com
E-mail: [email protected]
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any
interference that may be received, including interference that may
cause undesired operation. The manufacturer is not responsible
for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modification could void the
user’s authority to use the equipment.
CS
-
2013F
M

TABLE OF CONTENTS
Installation Cautions & Warnings…….………….…………………………...………………………………………………2-3
Suggested Component
Mounting………….……...……………………………...…………………………….……………....3
Wiring Information……………………………….……………………………..……………………………...………….…….4-
7
Power Door Lock Wiring...………………………..…………………………………….……………………………..….……8-
9
Remote Start: Tach & Tach-less Programming……………………………………..……………………………….……10-
11
Option Programming……………………………….…………….………………………...………………….…………….11-
15
Option Reset
Procedure…………………………..…………..…………………………………………………………….…..15
Custom “Personal” Override
Code………………..………………..…………………………………………………...……..16
Remote Sensor Adjust
Mode…………………………..……..…………………………………...……………………..…….16
One Way Transmitter
Programming.……..……………………………………….……………………………………..…….16
Two-Way Transceiver
Programming…………………….…..………………….…………………..………………...………17
Remote Control Diagrams…………………….…………………………………………………..……………..………....17-
18
Alarm Operation………………………………..………….…………………………………………..………………..…...18-
21
Remote-Less Protection “Beach
Mode”……………………………………………………………………...…………..……21

Prior Intrusion
Diagnostics………………………….………………………………………………………...……….…..……22
Remote Start Operation……………….…………………………………………………………………………..….……..22-
23
Special LCD FM Remote-Pager
Functions……….…………………………………………………………..………………24
INSTALLATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDOR shall not be responsible or liable in any way for accidents
or damage resulting from the use of this equipment. This system is designed to be professionally installed in a vehicle that is
in proper operating condition. Parking brake, Transmission, Throttle, and Engine Safety features must be in working order.
It is the vehicle owner’s responsibility to understand the operating features of this system.
DO NOT INSTALL CS2005FM ALARM/REMOTE STARTER in vehicles with MANUAL TRANSMISSIONS! There are no
safety features built into this unit for manual transmission vehicles. If accidentally left in gear, a remote started vehicle could
become a self-propelled threat to life and property.
INSTALLATION CAUTIONS & WARNINGS
DO NOT REMOTE START A VEHICLE IN A CLOSED AREA OR GARAGE! Make sure that door is open or there
is adequate ventilation is provided. Failure to observe this rule could result in serious injury or death from
poisonous Carbon Monoxide fumes! Also note this warning when programming this system for Cold Start
operation.
BEFORE BEGINNING INSTALLATION,check all vehicle manufacturer cautions and warnings regarding electrical
service. (AIR BAGS, ABS BRAKES, AND BATTERY).
DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering column,
or any other moving parts in the vehicle.
DO NOT EXCEED MAXIMUM OUTPUT RATINGS - SERIOUS DAMAGE MAY OCCUR. Limits for alarm and
remote start functions are listed in the main diagram and wiring descriptions page. If you are unsure about current
load, measure the load with an AMP-METER.
REMOVE MAIN SYSTEM FUSE(S) before jump starting the vehicle. DAMAGE MAY OCCUR TO SYSTEM IF
PROPER PRECAUTIONS ARE NOT OBSERVED.
DO NOT EXTEND REMOTE START/IGNITION OUTPUT HARNESS LENGTH. Locate the control module within
reach of the supplied IGNITION/START OUTPUT wires. Extending these wires could result in poor performance.

SUGGESTED COMPONENT MOUNTING
Control Module: Driver or Passenger side underdash, the unit should be placed as high as possible, not easily
accessible by an intruder.
Shock Sensor: Mount with wire ties to an under dash wire harness or fasten with screws to a panel.
Siren: Under the hood to fender-well or other body surface with the open end facing downward.
LED: In a visible location on the dashboard or console.
Override/Program button: Hidden location, but accessible to the user in case the system must be disarmed
without the use of the transmitter. This switch is also used to program certain features and to page/call the
transceiver from inside the vehicle if necessary.
Antenna Module: Inside front windshield (as high as possible) using supplied double sided tape.
WIRING
6 PIN HI-CURRENT REMOTE START CONNECTOR:
RED: +12V INPUT (30 Amp Fused)
RED: +12V INPUT (30 Amp Fused)
YELLOW: IGNITION 1 (Primary) Output
ORANGE: ACCESSORY Output
PURPLE: STARTER Output
BROWN: Multi Function Output (IGNITION #2 / ACCESSORY #2 / STARTER #2)
(Programmable, See option table #23. Default set for IGN 2 output)
20 PIN MAIN HARNESS PLUG:
GREEN/WHITE WIRE: +12V BRAKE INPUT
Connect this wire to the side of the brake pedal switch that shows +12V only when the brake is depressed. This
input is used to reset remote start after entering the running vehicle and turning the ignition key on.
BLACK/GRAY WIRE: TACH SIGNAL INPUT (Used For Tach Mode)
Used to monitor Tach Pulses when the engine is running. Connect to negative terminal of ignition coil, crankshaft
position sensor or ECM/PCM tach wire.
WHITE/RED WIRE: (-) AUX. REMOTE OUTPUT #2 (Optional)

Programmable Auxiliary Output Channel #2.
BLACK/WHITE WIRE: (-) DOME LIGHT ILLUMINATION (Optional, Requires Relay)
Connect to terminal 85 of relay. This wire turns the dome light on for 30 seconds upon disarming of the alarm. If
the ignition is turned on or the alarm is re-armed, the dome light will turn off again. Connect this wire to terminal 85
of a relay. Connect terminal 86 to +12V Constant. Connect terminal 87 to +12V or ground depending on the type of
Dome Light/Door Pin circuit that is in the vehicle.
YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS
Connect to an ignition wire (or fuse in the fuse box) that shows +12 Volts when the key in both “On” and “Start”
positions.
BLUE/YELLOW WIRE: (+12V) DIESEL GLOW PLUG INPUT
Connect Pink wire to indicator circuit that shows +12 volts while the “WAIT TO START LAMP” is on. When this
wire is used, the CS-2013FM unit will wait until light turns off before attempting a remote start. Note: a relay may be
required for vehicles that have a Negative Wait to Start lamp circuit.
WIRING
BLUE/WHITE WIRE: (-) PASSENGER DOOR UNLOCK OUTPUT (Optional, requires relay)
This wire activates when the unlock button on the remote is pressed a second time upon disarming. Connects to
unlock circuit for passenger door or doors when using split Driver & Passenger unlock configuration.
BLUE/ORANGE WIRE: (-) NEGATIVE GROUND WHEN RUNNING (For Anti-Theft Bypass Module)
Sends a constant Ground with remote start command. Use this wire to activate a Bypass Modules.
BLACK WIRE: SYSTEM CHASSIS GROUND
Connect to chassis metal of the vehicle. Scrape away any paint or dirt from the connection point to ensure a good
connection.
RED WIRE: +12V POWER INPUT (15 amp fuse)
Connect to +12 Volt source. Recommended location for this connection is at the vehicle battery positive terminal.
VIOLET WIRE: (+) DOOR TRIGGER INPUT
This wire is used for vehicles that show a positive voltage (12 volts) when the door is open such as Ford.
GREEN WIRE: (-) DOOR TRIGGER INPUT
Identify the wire that reads ground when any door is open and 12 volts when all doors are closed. Some isolated
door triggers. In this case you need to run an additional wires from the other doors or go directly to the wire that
triggers the vehicle’s dome light.

WHITE/BLACK WIRE: (-) HOOD/TRUNK TRIGGER (Mandatory For Hood Pin)
Input trigger for a grounding hood or trunk pin switch and to inhibit remote start if the hood is open. Connect to
existing hood and trunk pin switches that read ground when open. If no existing switches are available, install a
new pin switch. Note: DO NOT mount new pin switches in water pathways.
ORANGE WIRE: (-) NEGATIVE ARMED OUTPUT (STARTER DISABLE)
Sends constant Ground output when system is armed. This output is used for adding a starter disable relay. For
starter kill, cut starter wire and connect between 87A and 30 on relay. Connect orange wire to 85 and connect 86 to
Ignition Source that has voltage in the ON and CRANKING position. Be sure to connect the Purple Remote Starter
Cranking output to the Motor side of the Starter Disable Relay or it will not allow the Remote Starter to operate.
VIOLET/WHITE WIRE: (-) OEM FACTORY DISARM OUTPUT
Provides a ground pulse to DISARM the vehicle’s FACTORY anti-theft system prior to Remote Start. Connect this
wire to the vehicles' anti-theft disarm wire. This wire may be found coming off the Driver's door key switch or the
Factory Anti-theft control module.
WIRING
WHITE/VIOLET WIRE: (-) OEM FACTORY ARM OUTPUT
Provides a ground pulse to ARM the vehicles' FACTORY after Remote Start. Connect this wire to the vehicle’s anti-
theft Arm wire.
BROWN WIRE: (+) SIREN OUTPUT (3 amp max.)
Connect to RED siren wire.
GRAY WIRE: (-) AUX. REMOTE OUTPUT #1 (Trunk Pop)
Provides Negative Pulse output for Factory Electronic Trunk Release. Requires relay for Positive type circuits.
WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT
Connect to switched parking light wire at back of light switch. If this is not possible, connect directly to one of the
parking lights at the front of the vehicle. European may vehicles require separate right and left circuits. Use a dual
relay or 2 diodes to separate the output signal.
BROWN/WHITE WIRE: (-) HORN HONK or (-) NEGATIVE IGNITION OUTPUT (Optional, Programmable)
Negative pulsed output for Horn Honk. Can also be programmed for an additional negative run output (Option #24).
2 PIN (BLUE) PLUG: PROGRAM / OVERRIDE BUTTON
2 PIN (RED) PLUG: LED INDICATOR (Red Flashing Light)
3 PIN DOORLOCK (WHITE) PLUG:

GREEN: (-) NEGATIVE LOCK Connect directly to negative lock/unlock systems. If vehicle uses
RED: +12V For Relays positive door lock signals or reversing polarity type, then external
BLUE: (-) NEGATIVE UNLOCK relays must be added. See Power Door Lock Wiring: Pages 8-
9.
4 PIN (WHITE) SENSOR PLUG:
WHITE: NEGATIVE PRE-WARN
BLACK: SENSOR GROUND
BLUE: NEGATIVE TRIGGER
RED: SENSOR POWER
3 PIN (BLUE) DATA PLUG ON RIGHT SIDE OF MODULE: Data port for 2-WAY FM Transceiver Box &
Antenna
4 PIN (WHITE) DATA PLUG ON RIGHT SIDE OF MODULE: Port for optional extended range antenna for 1-
way remote control.
WIRING TABLE
20 PIN CONNECTOR (18 GA. WIRES)
PIN # COLOR DESCRIPTION
1 GREEN/WHITE (+) 12 BRAKE LIGHT INPUT
2 BLACK/GRAY TACH SIGNAL INPUT (ENGINE RPM0
3 WHITE/RED (-) AUXILIARY CHANNEL OUTPUT #2
4 BLACK/WHITE (-) DOME LIGHT SUPERVISION OUTPUT
5 YELLOW (+) 12V IGNITION SWITCH INPUT
6 BLUE/YELLOW (+) 12V GLOW PLUG INPUT
7 BLUE/WHITE (-) NEGATIVE PASSENGER UNLOCK OUTPUT
8 BLUE/ORANGE (-) NEGATIVE IGN. OUTPUT (GROUND WHEN
RUNNING)
9 BLACK (-) CHASSIS GROUND
10 RED (+) 12 POWER INPUT
11 VIOLET (+) POSITIVE DOOR TRIGGER INPUT

12 GREEN (-) NEGATIVE DOOR TRIGGER INPUT
13 WHITE/BLACK (-) HOOD/TRUNK TRIGGER INPUT
14 ORANGE (-) ARMED OUTPUT (STARTER DISABLE)
15 VIOLET/WHITE (-) OEM FACTORY DISARM OUTPUT
16 WHITE/VIOLET (-) OEM FACTORY ARM OUTPUT
17 BROWN (+) SIREN POSITIVE OUTPUT
18 GRAY (-) NEG AUXILIARY CHANNEL OUTPUT #1 (TRUNK
POP)
19 WHITE (+) 12V PARKING LIGHT OUTPUT
20 BROWN/WHITE (-) NEG HORN HONK OR NEG IGN OUTPUT
POWER DOOR LOCK WIRING

NEGATIVE TRIGGER DOORLOCK WIRING
POSITIVE TRIGGER DOORLOCK WIRING
GREEN
GREEN FUSED
RED +12VRED
BLUE +
BLUE
86
858685
8787
3087A30
87A
FACTORY
FACTORY
LL
POWER
POWER
LOCKING
LOCKING
UL UL
RELAYS RELAYS
AFTERMARKET DOOR LOCK WIRINGREVERSE POLARITY DOOR LOCK WIRING
GREEN
GREEN FUSED
FUSED RED
RED +12V
+12V
BLUE
BLUE +
+
86858685
86858685
8787
8787
3087A3087A
3087A3087A
+L
CUT
UL
CUT
MASTER
SWITCH
LOCK WIRE
UNLOCK WIRE
SEPARATE DRIVER’S DOOR UNLOCK WIRING

NEGATIVE TRIGGER DOOR LOCKS
BLUE/WHITE
GREEN
RED
BLUE
DRIVER'S
DOOR MOTOR
8685 LL
87
ULUL
87A
30
FACTORY LOCK
RELAYS
+12V
+FUSED
UNLOCK WIRE CUT
WIRING FOR REVERSE POLARITY DOOR LOCKS
BLUE/WHITE
GREEN FUSED
RED +12V
BLUE +
MASTER
86858685
SWITCH
8685 8787
87 30
87A
30
87A
30 87A
+
L
CUT
UL
CUT
CUT
UNLOCK WIRE
LOCK WIRE
REMOTE START:TACH & TACHLESS MODE