Crosley Furniture CO6214 User manual

Outdoor Dining Swivel Chair
CO6214

2
F
#2 #3
16 PCS(Extra 1) 4 PCS(Extra 1)
Flat Washer
28 PCS(Extra 1)
M6mm
#1 #4
M6*12mm
Long Bolt
M6*45mm
Allen Wrench
1 PC
M6mm
8 PCS(Extra 1)
Medium Bolt
M6*20mm
#5
PART LIST
A B CD
Back Panel
G
2 PCS
Seat Panel
2 PCS
Right Arm Panel
Seat Cushion
Cover *
2 PCS
Seat Cushion
Core
2 PCS
Back Cushion
Cover *
2 PCS
Back Cushion
Core
2 PCS
HI
*Please note cushion covers will ship separately.
Left Arm Panel
2 PCS
2 PCS
HARDWARE LIST
Short Bolt
E
2 PCS
Swivel
2 PCS
J

D
B
C
С
B
Step 1.
Attach seat panel (part B) to right arm panel (part C) using short bolts (part #1), flat
washers (part #4) and allen wrench (part #5).
NOTE: Please do not fully tighten bolts until unit is fully assembled.
Lay right arm panel (part С) down on a soft flat surface, such as carpet, as shown below.
Step 2.
washers (part #4) and allen wrench (part #5).
NOTE: Please do not fully tighten bolts until unit is fully assembled.
Attach left arm panel (part D) to seat panel (part B) using short bolts (part #1), flat
#4 x2
#1
#5 x1
x2
3
#5
#1
#4
#4 x2
#1
#5 x1
x2
#5
#4
#1

(part #4) and allen wrench (part #5).
NOTE: Please do not fully tighten bolts until unit is fully assembled.
С
B
D
A
Step 3.
long bolts (part #3), flat washers (part #4) and allen wrench (part #5).
Attach back panel (part A) to assembled unit (parts B, C & D) using short bolts (part #1),
Step 4.
Attach swivel (part E) to the seat panel (part B) using medium bolts (part #2), flat washers
4
#5
#3
#4
#1
#4
#5
#4 x6
#3
#5 x1
x2
#1 x4
NOTE: Please fully tighten all bolts at this time.
B
D
A
#4
#5
#2
E#4 x4
#5 x1
#2 x4

Step 5.
Attach swivel (part E) to the base (part F)
5
F
E
Step 6. Insert seat cushion core (part H) into seat cushion cover (part G).
lnsert back cushion core (part J) into back cushion cover (part I).
G
JI
H

Repeat steps 1-7 to assemble remaining chair.
Step 7. Place seat cushion and back cushion as shown below.
6
Back Cushion
Seat Cushion

Outdoor Dining Table
CO6215

Cap
HARDWARE LIST
#2 #3
Bolt
8 PCS (Extra 1)
Flat Washer
8 PCS (Extra 1)
#1 #4
M8*35mm
1 PC
PART LIST
A B
4 PCS
Top Panel
1 PC
2
M6mm
Leg
Wrench
1 PC

#4
Step 1.
Attach legs (part A) to top panel (part B) using bolts (part #1), flat washers (part #2) and
wrench (part #3).
NOTE: Please fully tighten all bolts at this time.
Lay top panel (part B) upside down on a soft flat surface, such as carpet, as shown below.
Step 2.
Carefully turn unit upright. Attach cap (part #4) to top panel (part B).
#2 x8
#1
#3 x1
x8
3
#1
#2 #3
A
B
B
NOTE: It is important to adjust levelers once fully assembled and upright. Extend adjustable
leveler until it’s firmly in contact with the floor. If relocating, adjust leveler as needed
until it’s firmly in contact with the floor in new location.
#4x1